LINUX.ORG.RU

История изменений

Исправление Xintrea, (текущая версия) :

Фига себе, простой фреймбуфер 4000 fps дает??

Я таки смог собрать Intel Linux Graphics Installer, оказывается они забыли в README про autoconf написать. После его работы появляется скрипт configure.

Однако запуск завершается сообщением:

Distribution not supported

И в логе написано:
Checking if Intel graphics card available...
  • checking for i915 module in /sys/module
  • i915 module found
Checking if Intel graphics card available... OK
Retrieving information from 01.org...
  • fetching https://download.01.org/gfx/ilg-config.cfg
  • saving to /root/.ilg-config
  • fetched 1626 bytes
  • fetched 9818 bytes
  • fetched 12301 bytes
  • looking up [Debian stretch] configuration
Retrieving information from 01.org... OK
Checking distribution... Failed

То есть, этим инсталлером поставить дрова Intel невозможно в Debian. Правда, непонятно, стоят ли они уже или нет. Как это узнать?

По поводу модуля i915 вот какая информация:
# lsmod | grep i915
i915                 1232896  0
drm_kms_helper        155648  1 i915
drm                   360448  2 i915,drm_kms_helper
i2c_algo_bit           16384  1 i915
video                  40960  1 i915
button                 16384  1 i915

# modinfo i915
filename:       /lib/modules/4.9.0-4-amd64/kernel/drivers/gpu/drm/i915/i915.ko
license:        GPL and additional rights
description:    Intel Graphics
author:         Intel Corporation
author:         Tungsten Graphics, Inc.
firmware:       i915/bxt_dmc_ver1_07.bin
firmware:       i915/skl_dmc_ver1_26.bin
firmware:       i915/kbl_dmc_ver1_01.bin
firmware:       i915/kbl_guc_ver9_14.bin
firmware:       i915/bxt_guc_ver8_7.bin
firmware:       i915/skl_guc_ver6_1.bin
alias:          pci:v00008086d0000593Bsv*sd*bc03sc*i* ... 
alias:          pci:v00008086d0000016Asv0000152Dsd00008990bc03sc*i* ...
alias:          pci:v00008086d00003577sv*sd*bc03sc*i*
depends:        drm_kms_helper,drm,video,button,i2c-algo-bit
intree:         Y
vermagic:       4.9.0-4-amd64 SMP mod_unload modversions 
parm:           modeset:Use kernel modesetting [KMS] (0=disable, 1=on, -1=force vga console preference [default]) (int)
parm:           panel_ignore_lid:Override lid status (0=autodetect, 1=autodetect disabled [default], -1=force lid closed, -2=force lid open) (int)
parm:           semaphores:Use semaphores for inter-ring sync (default: -1 (use per-chip defaults)) (int)
parm:           enable_rc6:Enable power-saving render C-state 6. Different stages can be selected via bitmask values (0 = disable; 1 = enable rc6; 2 = enable deep rc6; 4 = enable deepest rc6). For example, 3 would enable rc6 and deep rc6, and 7 would enable everything. default: -1 (use per-chip default) (int)
parm:           enable_dc:Enable power-saving display C-states. (-1=auto [default]; 0=disable; 1=up to DC5; 2=up to DC6) (int)
parm:           enable_fbc:Enable frame buffer compression for power savings (default: -1 (use per-chip default)) (int)
parm:           lvds_channel_mode:Specify LVDS channel mode (0=probe BIOS [default], 1=single-channel, 2=dual-channel) (int)
parm:           lvds_use_ssc:Use Spread Spectrum Clock with panels [LVDS/eDP] (default: auto from VBT) (int)
parm:           vbt_sdvo_panel_type:Override/Ignore selection of SDVO panel mode in the VBT (-2=ignore, -1=auto [default], index in VBT BIOS table) (int)
parm:           reset:Attempt GPU resets (default: true) (bool)
parm:           enable_hangcheck:Periodically check GPU activity for detecting hangs. WARNING: Disabling this can cause system wide hangs. (default: true) (bool)
parm:           enable_ppgtt:Override PPGTT usage. (-1=auto [default], 0=disabled, 1=aliasing, 2=full, 3=full with extended address space) (int)
parm:           enable_execlists:Override execlists usage. (-1=auto [default], 0=disabled, 1=enabled) (int)
parm:           enable_psr:Enable PSR (0=disabled, 1=enabled - link mode chosen per-platform, 2=force link-standby mode, 3=force link-off mode) Default: -1 (use per-chip default) (int)
parm:           preliminary_hw_support:Enable preliminary hardware support. (int)
parm:           disable_power_well:Disable display power wells when possible (-1=auto [default], 0=power wells always on, 1=power wells disabled when possible) (int)
parm:           enable_ips:Enable IPS (default: true) (int)
parm:           fastboot:Try to skip unnecessary mode sets at boot time (default: false) (bool)
parm:           prefault_disable:Disable page prefaulting for pread/pwrite/reloc (default:false). For developers only. (bool)
parm:           load_detect_test:Force-enable the VGA load detect code for testing (default:false). For developers only. (bool)
parm:           force_reset_modeset_test:Force a modeset during gpu reset for testing (default:false). For developers only. (bool)
parm:           invert_brightness:Invert backlight brightness (-1 force normal, 0 machine defaults, 1 force inversion), please report PCI device ID, subsystem vendor and subsystem device ID to dri-devel@lists.freedesktop.org, if your machine needs it. It will then be included in an upcoming module version. (int)
parm:           disable_display:Disable display (default: false) (bool)
parm:           enable_cmd_parser:Enable command parsing (1=enabled [default], 0=disabled) (int)
parm:           use_mmio_flip:use MMIO flips (-1=never, 0=driver discretion [default], 1=always) (int)
parm:           mmio_debug:Enable the MMIO debug code for the first N failures (default: off). This may negatively affect performance. (int)
parm:           verbose_state_checks:Enable verbose logs (ie. WARN_ON()) in case of unexpected hw state conditions. (bool)
parm:           nuclear_pageflip:Force atomic modeset functionality; asynchronous mode is not yet supported. (default: false). (bool)
parm:           edp_vswing:Ignore/Override vswing pre-emph table selection from VBT (0=use value from vbt [default], 1=low power swing(200mV),2=default swing(400mV)) (int)
parm:           enable_guc_loading:Enable GuC firmware loading (-1=auto, 0=never [default], 1=if available, 2=required) (int)
parm:           enable_guc_submission:Enable GuC submission (-1=auto, 0=never [default], 1=if available, 2=required) (int)
parm:           guc_log_level:GuC firmware logging level (-1:disabled (default), 0-3:enabled) (int)
parm:           enable_dp_mst:Enable multi-stream transport (MST) for new DisplayPort sinks. (default: true) (bool)
parm:           inject_load_failure:Force an error after a number of failure check points (0:disabled (default), N:force failure at the Nth failure check point) (uint)
parm:           enable_dpcd_backlight:Enable support for DPCD backlight control (default:false) (bool)
parm:           enable_gvt:Enable support for Intel GVT-g graphics virtualization host support(default:false) (bool)

В общем, надо разобраться: стоят ли драйвера Intel или их надо таки вручную ставить. Если надо, то как их поставить, если Intel Linux Graphics Installer их ставить не хочет.

Исходная версия Xintrea, :

Фига себе, простой фреймбуфер 4000 fps дает??

Я таки смог собрать Intel Linux Graphics Installer, оказывается они забыли в README про autoconf написать. После его работы появляется скрипт configure.

Однако запуск завершается сообщением:

Distribution not supperted

И в логе написано:
Checking if Intel graphics card available...
  • checking for i915 module in /sys/module
  • i915 module found
Checking if Intel graphics card available... OK
Retrieving information from 01.org...
  • fetching https://download.01.org/gfx/ilg-config.cfg
  • saving to /root/.ilg-config
  • fetched 1626 bytes
  • fetched 9818 bytes
  • fetched 12301 bytes
  • looking up [Debian stretch] configuration
Retrieving information from 01.org... OK
Checking distribution... Failed

То есть, этим инсталлером поставить дрова Intel невозможно в Debian. Правда, непонятно, стоят ли они уже или нет. Как это узнать?

По поводу модуля i915 вот какая информация:
# lsmod | grep i915
i915                 1232896  0
drm_kms_helper        155648  1 i915
drm                   360448  2 i915,drm_kms_helper
i2c_algo_bit           16384  1 i915
video                  40960  1 i915
button                 16384  1 i915

# modinfo i915
filename:       /lib/modules/4.9.0-4-amd64/kernel/drivers/gpu/drm/i915/i915.ko
license:        GPL and additional rights
description:    Intel Graphics
author:         Intel Corporation
author:         Tungsten Graphics, Inc.
firmware:       i915/bxt_dmc_ver1_07.bin
firmware:       i915/skl_dmc_ver1_26.bin
firmware:       i915/kbl_dmc_ver1_01.bin
firmware:       i915/kbl_guc_ver9_14.bin
firmware:       i915/bxt_guc_ver8_7.bin
firmware:       i915/skl_guc_ver6_1.bin
alias:          pci:v00008086d0000593Bsv*sd*bc03sc*i* ... 
alias:          pci:v00008086d0000016Asv0000152Dsd00008990bc03sc*i* ...
alias:          pci:v00008086d00003577sv*sd*bc03sc*i*
depends:        drm_kms_helper,drm,video,button,i2c-algo-bit
intree:         Y
vermagic:       4.9.0-4-amd64 SMP mod_unload modversions 
parm:           modeset:Use kernel modesetting [KMS] (0=disable, 1=on, -1=force vga console preference [default]) (int)
parm:           panel_ignore_lid:Override lid status (0=autodetect, 1=autodetect disabled [default], -1=force lid closed, -2=force lid open) (int)
parm:           semaphores:Use semaphores for inter-ring sync (default: -1 (use per-chip defaults)) (int)
parm:           enable_rc6:Enable power-saving render C-state 6. Different stages can be selected via bitmask values (0 = disable; 1 = enable rc6; 2 = enable deep rc6; 4 = enable deepest rc6). For example, 3 would enable rc6 and deep rc6, and 7 would enable everything. default: -1 (use per-chip default) (int)
parm:           enable_dc:Enable power-saving display C-states. (-1=auto [default]; 0=disable; 1=up to DC5; 2=up to DC6) (int)
parm:           enable_fbc:Enable frame buffer compression for power savings (default: -1 (use per-chip default)) (int)
parm:           lvds_channel_mode:Specify LVDS channel mode (0=probe BIOS [default], 1=single-channel, 2=dual-channel) (int)
parm:           lvds_use_ssc:Use Spread Spectrum Clock with panels [LVDS/eDP] (default: auto from VBT) (int)
parm:           vbt_sdvo_panel_type:Override/Ignore selection of SDVO panel mode in the VBT (-2=ignore, -1=auto [default], index in VBT BIOS table) (int)
parm:           reset:Attempt GPU resets (default: true) (bool)
parm:           enable_hangcheck:Periodically check GPU activity for detecting hangs. WARNING: Disabling this can cause system wide hangs. (default: true) (bool)
parm:           enable_ppgtt:Override PPGTT usage. (-1=auto [default], 0=disabled, 1=aliasing, 2=full, 3=full with extended address space) (int)
parm:           enable_execlists:Override execlists usage. (-1=auto [default], 0=disabled, 1=enabled) (int)
parm:           enable_psr:Enable PSR (0=disabled, 1=enabled - link mode chosen per-platform, 2=force link-standby mode, 3=force link-off mode) Default: -1 (use per-chip default) (int)
parm:           preliminary_hw_support:Enable preliminary hardware support. (int)
parm:           disable_power_well:Disable display power wells when possible (-1=auto [default], 0=power wells always on, 1=power wells disabled when possible) (int)
parm:           enable_ips:Enable IPS (default: true) (int)
parm:           fastboot:Try to skip unnecessary mode sets at boot time (default: false) (bool)
parm:           prefault_disable:Disable page prefaulting for pread/pwrite/reloc (default:false). For developers only. (bool)
parm:           load_detect_test:Force-enable the VGA load detect code for testing (default:false). For developers only. (bool)
parm:           force_reset_modeset_test:Force a modeset during gpu reset for testing (default:false). For developers only. (bool)
parm:           invert_brightness:Invert backlight brightness (-1 force normal, 0 machine defaults, 1 force inversion), please report PCI device ID, subsystem vendor and subsystem device ID to dri-devel@lists.freedesktop.org, if your machine needs it. It will then be included in an upcoming module version. (int)
parm:           disable_display:Disable display (default: false) (bool)
parm:           enable_cmd_parser:Enable command parsing (1=enabled [default], 0=disabled) (int)
parm:           use_mmio_flip:use MMIO flips (-1=never, 0=driver discretion [default], 1=always) (int)
parm:           mmio_debug:Enable the MMIO debug code for the first N failures (default: off). This may negatively affect performance. (int)
parm:           verbose_state_checks:Enable verbose logs (ie. WARN_ON()) in case of unexpected hw state conditions. (bool)
parm:           nuclear_pageflip:Force atomic modeset functionality; asynchronous mode is not yet supported. (default: false). (bool)
parm:           edp_vswing:Ignore/Override vswing pre-emph table selection from VBT (0=use value from vbt [default], 1=low power swing(200mV),2=default swing(400mV)) (int)
parm:           enable_guc_loading:Enable GuC firmware loading (-1=auto, 0=never [default], 1=if available, 2=required) (int)
parm:           enable_guc_submission:Enable GuC submission (-1=auto, 0=never [default], 1=if available, 2=required) (int)
parm:           guc_log_level:GuC firmware logging level (-1:disabled (default), 0-3:enabled) (int)
parm:           enable_dp_mst:Enable multi-stream transport (MST) for new DisplayPort sinks. (default: true) (bool)
parm:           inject_load_failure:Force an error after a number of failure check points (0:disabled (default), N:force failure at the Nth failure check point) (uint)
parm:           enable_dpcd_backlight:Enable support for DPCD backlight control (default:false) (bool)
parm:           enable_gvt:Enable support for Intel GVT-g graphics virtualization host support(default:false) (bool)

В общем, надо разобраться: стоят ли драйвера Intel или их надо таки вручную ставить. Если надо, то как их поставить, если Intel Linux Graphics Installer их ставить не хочет.