История изменений

Исправление niXman, 13.05.19 17:31 (текущая версия) :

вроде все настроил, но пока что на локальном девайсе.

файл '/etc/network/interfaces' удалил полностью.

все настройки вписал в '/etc/netplan/eth0.yaml':

network:
  version: 2
  renderer: networkd
  ethernets:
    eth0:
      dhcp4: false
  bridges:
      br0:
        dhcp4: false
        addresses: [192.168.0.61/24]
        gateway4: 192.168.0.1
        interfaces:
          - eth0
        nameservers:
          addresses: [8.8.8.8]

ifconfig выдает такое:

br0: flags=4163<UP,BROADCAST,RUNNING,MULTICAST>  mtu 1500
        inet 192.168.0.61  netmask 255.255.255.0  broadcast 192.168.0.255
        inet6 fe80::14ef:9bff:fed2:6ef6  prefixlen 64  scopeid 0x20<link>
        ether 16:ef:9b:d2:6e:f6  txqueuelen 1000  (Ethernet)
        RX packets 585  bytes 70493 (70.4 KB)
        RX errors 0  dropped 0  overruns 0  frame 0
        TX packets 302  bytes 119991 (119.9 KB)
        TX errors 0  dropped 0 overruns 0  carrier 0  collisions 0

eth0: flags=4163<UP,BROADCAST,RUNNING,MULTICAST>  mtu 1500
        ether 06:3d:17:27:13:6c  txqueuelen 1000  (Ethernet)
        RX packets 729  bytes 126815 (126.8 KB)
        RX errors 0  dropped 0  overruns 0  frame 0
        TX packets 330  bytes 126067 (126.0 KB)
        TX errors 0  dropped 0 overruns 0  carrier 0  collisions 0
        device interrupt 24  

lo: flags=73<UP,LOOPBACK,RUNNING>  mtu 65536
        inet 127.0.0.1  netmask 255.0.0.0
        inet6 ::1  prefixlen 128  scopeid 0x10<host>
        loop  txqueuelen 1  (Local Loopback)
        RX packets 114  bytes 8146 (8.1 KB)
        RX errors 0  dropped 0  overruns 0  frame 0
        TX packets 114  bytes 8146 (8.1 KB)
        TX errors 0  dropped 0 overruns 0  carrier 0  collisions 0

p2p0: flags=4099<UP,BROADCAST,MULTICAST>  mtu 1500
        ether 52:3e:aa:da:7d:a0  txqueuelen 1000  (Ethernet)
        RX packets 0  bytes 0 (0.0 B)
        RX errors 0  dropped 1  overruns 0  frame 0
        TX packets 0  bytes 0 (0.0 B)
        TX errors 0  dropped 0 overruns 0  carrier 0  collisions 0

wlx503eaada7da0: flags=4099<UP,BROADCAST,MULTICAST>  mtu 1500
        ether 50:3e:aa:da:7d:a0  txqueuelen 1000  (Ethernet)
        RX packets 0  bytes 0 (0.0 B)
        RX errors 0  dropped 1  overruns 0  frame 0
        TX packets 0  bytes 0 (0.0 B)
        TX errors 0  dropped 0 overruns 0  carrier 0  collisions 0

'ip a' выдает такое:

1: lo: <LOOPBACK,UP,LOWER_UP> mtu 65536 qdisc noqueue state UNKNOWN group default qlen 1
    link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
    inet 127.0.0.1/8 scope host lo
       valid_lft forever preferred_lft forever
    inet6 ::1/128 scope host 
       valid_lft forever preferred_lft forever
2: eth0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc fq_codel master br0 state UNKNOWN group default qlen 1000
    link/ether 06:3d:17:27:13:6c brd ff:ff:ff:ff:ff:ff
3: br0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc noqueue state UP group default qlen 1000
    link/ether 16:ef:9b:d2:6e:f6 brd ff:ff:ff:ff:ff:ff
    inet 192.168.0.61/24 brd 192.168.0.255 scope global br0
       valid_lft forever preferred_lft forever
    inet6 fe80::14ef:9bff:fed2:6ef6/64 scope link 
       valid_lft forever preferred_lft forever
4: wlx503eaada7da0: <NO-CARRIER,BROADCAST,MULTICAST,UP> mtu 1500 qdisc mq state DOWN group default qlen 1000
    link/ether 50:3e:aa:da:7d:a0 brd ff:ff:ff:ff:ff:ff
5: p2p0: <NO-CARRIER,BROADCAST,MULTICAST,UP> mtu 1500 qdisc mq state DOWN group default qlen 1000
    link/ether 52:3e:aa:da:7d:a0 brd ff:ff:ff:ff:ff:ff

'ip route show' выдает такое:

default via 192.168.0.1 dev br0 proto static 
192.168.0.0/24 dev br0 proto kernel scope link src 192.168.0.61

одно чего ясейчас не знаю, смогу ли я подключиться к удаленному девайсу из мира, если настрою его соответствующим образом? (за исключением статического IP)

Исходная версия niXman, 13.05.19 17:29: