Старый купленый 2011 FreeAgent_GoFlex_Drive USB 1Tбайт перестал не удаляет файлы, походу хана? запускаю sudo smartctl -d sat –test=long /dev/sdd отваливается Self-test execution status: ( 249) запускаю через программу SeaTools или gnome-disks – так он бесконечно крутить self-test short данные с диска считал, файловая система NTFS говорит порядок проверял 2 раза chkdsk *: /r
как начинаю удалять файлы или что-то писать хана… говорит удалилось и записалось диск перетыкаешь USB-диск ничего не поменялось.
Что куда копать подскажите, может контакты спиртом промыть? или выбросить HDD не мучиться?
=== START OF READ SMART DATA SECTION ===
SMART Status not supported: Incomplete response, ATA output registers missing
SMART overall-health self-assessment test result: PASSED
Warning: This result is based on an Attribute check.
General SMART Values:
Offline data collection status: (0x82) Offline data collection activity
was completed without error.
Auto Offline Data Collection: Enabled.
Self-test execution status: ( 249) Self-test routine in progress...
90% of test remaining.
Total time to complete Offline
data collection: ( 678) seconds.
Offline data collection
capabilities: (0x7b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 1) minutes.
Extended self-test routine
recommended polling time: ( 264) minutes.
Conveyance self-test routine
recommended polling time: ( 2) minutes.
SCT capabilities: (0x103b) SCT Status supported.
SCT Error Recovery Control supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 10
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x000f 128 099 006 Pre-fail Always - 1797311640
3 Spin_Up_Time 0x0003 095 092 000 Pre-fail Always - 0
4 Start_Stop_Count 0x0032 097 097 020 Old_age Always - 3449
5 Reallocated_Sector_Ct 0x0033 100 100 036 Pre-fail Always - 0
7 Seek_Error_Rate 0x000f 078 060 030 Pre-fail Always - 61765485
9 Power_On_Hours 0x0032 098 098 000 Old_age Always - 1775
10 Spin_Retry_Count 0x0013 100 100 097 Pre-fail Always - 0
12 Power_Cycle_Count 0x0032 099 099 020 Old_age Always - 1732
183 Runtime_Bad_Block 0x0032 100 100 000 Old_age Always - 0
184 End-to-End_Error 0x0032 100 100 099 Old_age Always - 0
187 Reported_Uncorrect 0x0032 099 099 000 Old_age Always - 1
188 Command_Timeout 0x0032 100 098 000 Old_age Always - 65562
189 High_Fly_Writes 0x003a 100 100 000 Old_age Always - 0
190 Airflow_Temperature_Cel 0x0022 072 049 045 Old_age Always - 28 (Min/Max 27/32)
191 G-Sense_Error_Rate 0x0032 100 100 000 Old_age Always - 0
192 Power-Off_Retract_Count 0x0032 100 100 000 Old_age Always - 612
193 Load_Cycle_Count 0x0032 096 096 000 Old_age Always - 8509
194 Temperature_Celsius 0x0022 028 051 000 Old_age Always - 28 (0 5 0 0 0)
195 Hardware_ECC_Recovered 0x001a 037 020 000 Old_age Always - 1797311640
197 Current_Pending_Sector 0x0012 100 100 000 Old_age Always - 0
198 Offline_Uncorrectable 0x0010 100 100 000 Old_age Offline - 0
199 UDMA_CRC_Error_Count 0x003e 200 200 000 Old_age Always - 0
240 Head_Flying_Hours 0x0000 100 253 000 Old_age Offline - 3282 (240 43 0)
241 Total_LBAs_Written 0x0000 100 253 000 Old_age Offline - 2592920482
242 Total_LBAs_Read 0x0000 100 253 000 Old_age Offline - 2747706242
SMART Error Log Version: 1
ATA Error Count: 1
CR = Command Register [HEX]
FR = Features Register [HEX]
SC = Sector Count Register [HEX]
SN = Sector Number Register [HEX]
CL = Cylinder Low Register [HEX]
CH = Cylinder High Register [HEX]
DH = Device/Head Register [HEX]
DC = Device Command Register [HEX]
ER = Error register [HEX]
ST = Status register [HEX]
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.
Error 1 occurred at disk power-on lifetime: 1196 hours (49 days + 20 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 00 ff ff ff 0f Error: UNC at LBA = 0x0fffffff = 268435455
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
25 00 08 ff ff ff 4f 00 00:00:37.904 READ DMA EXT
25 00 08 ff ff ff 4f 00 00:00:37.904 READ DMA EXT
25 00 08 ff ff ff 4f 00 00:00:37.903 READ DMA EXT
25 00 08 ff ff ff 4f 00 00:00:37.903 READ DMA EXT
25 00 08 ff ff ff 4f 00 00:00:37.902 READ DMA EXT
SMART Self-test log structure revision number 1
Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error
# 1 Short offline Completed without error 00% 1569 -
# 2 Extended offline Aborted by host 90% 1235 -
# 3 Extended offline Aborted by host 90% 1235 -
# 4 Conveyance offline Completed without error 00% 1235 -
# 5 Short offline Completed without error 00% 1235 -
# 6 Extended offline Aborted by host 90% 1235 -
# 7 Extended offline Aborted by host 90% 1219 -
# 8 Short offline Completed without error 00% 1219 -
# 9 Short offline Completed without error 00% 1219 -
#10 Extended offline Completed: read failure 60% 1219 867582832
#11 Conveyance offline Completed without error 00% 1218 -
#12 Short offline Completed without error 00% 1218 -
#13 Short offline Completed without error 00% 1217 -
#14 Extended offline Aborted by host 90% 1217 -
#15 Short offline Completed without error 00% 1203 -
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
