История изменений
Исправление
int13h,
(текущая версия)
:
Ок. Я вообще не знаю, что сейчас на десктопах по винтам. У меня сейчас вообще трэш и содомия - винт из ноутбука. 30% в бэдах - на месте их «пустые» разделы. И как не странно год уже использую его. Все необходимые данные заливаю по sftp на свой сервер. Просто пока необходимости не было в накопители.
Сейчас понадобились - выбираю.
Вот такой вот выхлоп:
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x002f 199 198 051 Pre-fail Always - 12962
3 Spin_Up_Time 0x0027 186 185 021 Pre-fail Always - 1675
4 Start_Stop_Count 0x0032 095 095 000 Old_age Always - 5610
5 Reallocated_Sector_Ct 0x0033 029 029 140 Pre-fail Always FAILING_NOW 1365
7 Seek_Error_Rate 0x002e 200 200 000 Old_age Always - 0
9 Power_On_Hours 0x0032 077 077 000 Old_age Always - 16946
10 Spin_Retry_Count 0x0033 100 099 051 Pre-fail Always - 1
11 Calibration_Retry_Count 0x0032 100 100 000 Old_age Always - 0
12 Power_Cycle_Count 0x0032 096 096 000 Old_age Always - 4952
192 Power-Off_Retract_Count 0x0032 199 199 000 Old_age Always - 852
193 Load_Cycle_Count 0x0032 001 001 000 Old_age Always - 669086
194 Temperature_Celsius 0x0022 112 094 000 Old_age Always - 35
196 Reallocated_Event_Count 0x0032 001 001 000 Old_age Always - 249
197 Current_Pending_Sector 0x0032 200 199 000 Old_age Always - 0
198 Offline_Uncorrectable 0x0030 100 253 000 Old_age Offline - 0
199 UDMA_CRC_Error_Count 0x0032 200 200 000 Old_age Always - 0
200 Multi_Zone_Error_Rate 0x0009 100 253 051 Pre-fail Offline - 0
SMART Error Log Version: 1
Warning: ATA error count 9819 inconsistent with error log pointer 1
ATA Error Count: 9819 (device log contains only the most recent five errors)
CR = Command Register [HEX]
FR = Features Register [HEX]
SC = Sector Count Register [HEX]
SN = Sector Number Register [HEX]
CL = Cylinder Low Register [HEX]
CH = Cylinder High Register [HEX]
DH = Device/Head Register [HEX]
DC = Device Command Register [HEX]
ER = Error register [HEX]
ST = Status register [HEX]
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.
Error 9819 occurred at disk power-on lifetime: 16941 hours (705 days + 21 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 00 71 8a 5c 40 Error: UNC at LBA = 0x005c8a71 = 6064753
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
60 08 d0 a0 91 7b 17 08 03:52:04.541 READ FPDMA QUEUED
60 08 58 58 f1 bf 12 08 03:52:04.531 READ FPDMA QUEUED
60 08 a0 d8 fc 1e 11 08 03:52:04.524 READ FPDMA QUEUED
60 08 18 a0 4a c5 19 08 03:52:04.517 READ FPDMA QUEUED
60 08 38 28 1f 21 0d 08 03:52:04.513 READ FPDMA QUEUED
Error 9818 occurred at disk power-on lifetime: 15967 hours (665 days + 7 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 00 d9 bb 62 40 Error: UNC at LBA = 0x0062bbd9 = 6470617
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
60 08 f0 08 8d f4 06 08 03:13:58.479 READ FPDMA QUEUED
60 08 e8 90 be 1c 07 08 03:13:58.477 READ FPDMA QUEUED
60 20 e0 38 3a 4c 07 08 03:13:58.465 READ FPDMA QUEUED
60 20 d8 d8 bb 62 1c 08 03:13:58.441 READ FPDMA QUEUED
60 18 d0 c0 bb 62 1c 08 03:13:58.435 READ FPDMA QUEUED
Error 9817 occurred at disk power-on lifetime: 15915 hours (663 days + 3 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
04 61 02 00 00 00 a0 Device Fault; Error: ABRT
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
ef 10 02 00 00 00 00 00 1d+09:41:59.630 SET FEATURES [Enable SATA feature]
ec 00 00 00 00 00 00 00 1d+09:41:59.629 IDENTIFY DEVICE
ef 03 46 00 00 00 00 00 1d+09:41:59.629 SET FEATURES [Set transfer mode]
ef 10 02 00 00 00 00 00 1d+09:41:59.628 SET FEATURES [Enable SATA feature]
ec 00 00 00 00 00 00 00 1d+09:41:59.627 IDENTIFY DEVICE
Error 9816 occurred at disk power-on lifetime: 15915 hours (663 days + 3 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
04 61 46 00 00 00 a0 Device Fault; Error: ABRT
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
ef 03 46 00 00 00 00 00 1d+09:41:59.629 SET FEATURES [Set transfer mode]
ef 10 02 00 00 00 00 00 1d+09:41:59.628 SET FEATURES [Enable SATA feature]
ec 00 00 00 00 00 00 00 1d+09:41:59.627 IDENTIFY DEVICE
c8 00 08 36 6d e8 00 00 1d+09:41:59.618 READ DMA
ef 10 02 00 00 00 00 00 1d+09:41:59.618 SET FEATURES [Enable SATA feature]
Error 9815 occurred at disk power-on lifetime: 15915 hours (663 days + 3 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
04 61 02 00 00 00 a0 Device Fault; Error: ABRT
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
ef 10 02 00 00 00 00 00 1d+09:41:59.628 SET FEATURES [Enable SATA feature]
ec 00 00 00 00 00 00 00 1d+09:41:59.627 IDENTIFY DEVICE
c8 00 08 36 6d e8 00 00 1d+09:41:59.618 READ DMA
ef 10 02 00 00 00 00 00 1d+09:41:59.618 SET FEATURES [Enable SATA feature]
ec 00 00 00 00 00 00 00 1d+09:41:59.615 IDENTIFY DEVICE
SMART Self-test log structure revision number 1
Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error
# 1 Short offline Completed without error 00% 6596 -
# 2 Short offline Completed without error 00% 4910 -
# 3 Short offline Completed without error 00% 4669 -
# 4 Short offline Aborted by host 10% 3214 -
# 5 Short offline Interrupted (host reset) 90% 1115 -
# 6 Short offline Interrupted (host reset) 90% 645 -
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
Исходная версия
int13h,
:
Ок. Я вообще не знаю, что сейчас на десктопах по винтам. У меня сейчас вообще трэш и содомия -
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x002f 199 198 051 Pre-fail Always - 12962
3 Spin_Up_Time 0x0027 186 185 021 Pre-fail Always - 1675
4 Start_Stop_Count 0x0032 095 095 000 Old_age Always - 5610
5 Reallocated_Sector_Ct 0x0033 029 029 140 Pre-fail Always FAILING_NOW 1365
7 Seek_Error_Rate 0x002e 200 200 000 Old_age Always - 0
9 Power_On_Hours 0x0032 077 077 000 Old_age Always - 16946
10 Spin_Retry_Count 0x0033 100 099 051 Pre-fail Always - 1
11 Calibration_Retry_Count 0x0032 100 100 000 Old_age Always - 0
12 Power_Cycle_Count 0x0032 096 096 000 Old_age Always - 4952
192 Power-Off_Retract_Count 0x0032 199 199 000 Old_age Always - 852
193 Load_Cycle_Count 0x0032 001 001 000 Old_age Always - 669086
194 Temperature_Celsius 0x0022 112 094 000 Old_age Always - 35
196 Reallocated_Event_Count 0x0032 001 001 000 Old_age Always - 249
197 Current_Pending_Sector 0x0032 200 199 000 Old_age Always - 0
198 Offline_Uncorrectable 0x0030 100 253 000 Old_age Offline - 0
199 UDMA_CRC_Error_Count 0x0032 200 200 000 Old_age Always - 0
200 Multi_Zone_Error_Rate 0x0009 100 253 051 Pre-fail Offline - 0
SMART Error Log Version: 1
Warning: ATA error count 9819 inconsistent with error log pointer 1
ATA Error Count: 9819 (device log contains only the most recent five errors)
CR = Command Register [HEX]
FR = Features Register [HEX]
SC = Sector Count Register [HEX]
SN = Sector Number Register [HEX]
CL = Cylinder Low Register [HEX]
CH = Cylinder High Register [HEX]
DH = Device/Head Register [HEX]
DC = Device Command Register [HEX]
ER = Error register [HEX]
ST = Status register [HEX]
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.
Error 9819 occurred at disk power-on lifetime: 16941 hours (705 days + 21 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 00 71 8a 5c 40 Error: UNC at LBA = 0x005c8a71 = 6064753
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
60 08 d0 a0 91 7b 17 08 03:52:04.541 READ FPDMA QUEUED
60 08 58 58 f1 bf 12 08 03:52:04.531 READ FPDMA QUEUED
60 08 a0 d8 fc 1e 11 08 03:52:04.524 READ FPDMA QUEUED
60 08 18 a0 4a c5 19 08 03:52:04.517 READ FPDMA QUEUED
60 08 38 28 1f 21 0d 08 03:52:04.513 READ FPDMA QUEUED
Error 9818 occurred at disk power-on lifetime: 15967 hours (665 days + 7 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 00 d9 bb 62 40 Error: UNC at LBA = 0x0062bbd9 = 6470617
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
60 08 f0 08 8d f4 06 08 03:13:58.479 READ FPDMA QUEUED
60 08 e8 90 be 1c 07 08 03:13:58.477 READ FPDMA QUEUED
60 20 e0 38 3a 4c 07 08 03:13:58.465 READ FPDMA QUEUED
60 20 d8 d8 bb 62 1c 08 03:13:58.441 READ FPDMA QUEUED
60 18 d0 c0 bb 62 1c 08 03:13:58.435 READ FPDMA QUEUED
Error 9817 occurred at disk power-on lifetime: 15915 hours (663 days + 3 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
04 61 02 00 00 00 a0 Device Fault; Error: ABRT
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
ef 10 02 00 00 00 00 00 1d+09:41:59.630 SET FEATURES [Enable SATA feature]
ec 00 00 00 00 00 00 00 1d+09:41:59.629 IDENTIFY DEVICE
ef 03 46 00 00 00 00 00 1d+09:41:59.629 SET FEATURES [Set transfer mode]
ef 10 02 00 00 00 00 00 1d+09:41:59.628 SET FEATURES [Enable SATA feature]
ec 00 00 00 00 00 00 00 1d+09:41:59.627 IDENTIFY DEVICE
Error 9816 occurred at disk power-on lifetime: 15915 hours (663 days + 3 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
04 61 46 00 00 00 a0 Device Fault; Error: ABRT
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
ef 03 46 00 00 00 00 00 1d+09:41:59.629 SET FEATURES [Set transfer mode]
ef 10 02 00 00 00 00 00 1d+09:41:59.628 SET FEATURES [Enable SATA feature]
ec 00 00 00 00 00 00 00 1d+09:41:59.627 IDENTIFY DEVICE
c8 00 08 36 6d e8 00 00 1d+09:41:59.618 READ DMA
ef 10 02 00 00 00 00 00 1d+09:41:59.618 SET FEATURES [Enable SATA feature]
Error 9815 occurred at disk power-on lifetime: 15915 hours (663 days + 3 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
04 61 02 00 00 00 a0 Device Fault; Error: ABRT
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
ef 10 02 00 00 00 00 00 1d+09:41:59.628 SET FEATURES [Enable SATA feature]
ec 00 00 00 00 00 00 00 1d+09:41:59.627 IDENTIFY DEVICE
c8 00 08 36 6d e8 00 00 1d+09:41:59.618 READ DMA
ef 10 02 00 00 00 00 00 1d+09:41:59.618 SET FEATURES [Enable SATA feature]
ec 00 00 00 00 00 00 00 1d+09:41:59.615 IDENTIFY DEVICE
SMART Self-test log structure revision number 1
Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error
# 1 Short offline Completed without error 00% 6596 -
# 2 Short offline Completed without error 00% 4910 -
# 3 Short offline Completed without error 00% 4669 -
# 4 Short offline Aborted by host 10% 3214 -
# 5 Short offline Interrupted (host reset) 90% 1115 -
# 6 Short offline Interrupted (host reset) 90% 645 -
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.