LINUX.ORG.RU

Сообщения deuser

 

Как работать с gpio на vortex86dx?

Форум — General

Сильно не пинайте, я новичок. Попал в руки интересный маленький компьютер на vortex86dx, В мануал описаны наличие колодки с gpio, но как с ними работать через туже sysfs?

Если для другой платы типа soekris net5501 в мануале есть подобное:

https://i.ibb.co/hcdZV3R/Screenshot-2022-02-03-at-12-53-49-net5501-manual-r010-doc-net5501-manual-pdf.png

Тоесть, есть карта, как пины на колодке соотносятся с ножками на контроллере. Для vortex86 я такой информации что-то не нашел. (или плохо искал, чего-то не понял) Может кто-то сталкивался? В какую сторону копать?

ps/ Тот же вопрос верен и для других x86, я вижу колодку с gpio на плате с geode lx800 и т.д Но в ближайшем приближение не вижу карты по пинам. Чего-то не понимаю.

 

deuser
()

Фреймбуфер и мусор при загрузке. Как победить?

Форум — General

Сильно не пинайте, новичок в Linux. Суть вопроса такова. При загрузке системы до начала работы фреймбувера падает «мусор» в некрасивом разрешение. С тем ничего нельзя сделать или я что-то делаю не так? Драйвер фреймбуфера в ядре.

lilo.conf:

# Start LILO global section
# Append any additional kernel parameters:
lba32
append = "vt.default_utf8=1 root=PARTUUID=0e1c2c37-01 video=lxfb.mode_option=1280x1024@75"
boot = /dev/sdb
...
image = /boot/vmlinuz-4.4.276-geode1
label = NewKernel
read-only

.config:

CONFIG_FB_GEODE=y
CONFIG_FB_GEODE_LX=y

Быстро пробегает это: https://i.ibb.co/WKZ7WWk/1642353194627.jpg ,a потом уже неспешно это: https://i.ibb.co/9cxqRtc/1642353141123.jpg

 

deuser
()

d2500cc странное поведение с mini pci express

Форум — Linux-hardware

Собрал домашний шлюз на d2500cc. Стал настраивать точку доступа на базе модуля wle900vx, все работает и скорость тоже вроде нормальная, 802.11ac пока нет клиентов. Но ~100mbit на intel 4965 оно выдает, интернет пока этим ограничен. В планах гигабитный интернет, там уже посмотрим, надо ли покупать что-то типа intel 7260 на клиенты.

И столкнулся с такой странностью. Система не видит модуль вообще. Нужно сделать poweroff, потом опять poweroff, тогда он есть. Если сделать reboot, его опять нет, до повторения связки с poweroff. Нет его по lspci, в dmesg вроде тоже ничего криминального. С чем такое может быть связано?

Это после poweroff

[    0.000000] Linux version 4.9.189-ath-regd (root@devuan) (gcc version 6.3.0 20170516 (Debian 6.3.0-18+deb9u1) ) #1 SMP Wed Dec 4 19:06:16 UTC 2019
[    0.000000] Command line: BOOT_IMAGE=/boot/vmlinuz-4.9.189-ath-regd root=UUID=903ff076-53bc-4745-a66a-34faad0960cf ro quiet vga=0x031b quiet elevator=noop ipv6.disable=1 vga=0x031b
[    0.000000] Disabled fast string operations
[    0.000000] x86/fpu: Legacy x87 FPU detected.
[    0.000000] e820: BIOS-provided physical RAM map:
[    0.000000] BIOS-e820: [mem 0x0000000000000000-0x000000000008efff] usable
[    0.000000] BIOS-e820: [mem 0x000000000008f000-0x000000000008ffff] reserved
[    0.000000] BIOS-e820: [mem 0x0000000000090000-0x000000000009e7ff] usable
[    0.000000] BIOS-e820: [mem 0x000000000009e800-0x000000000009ffff] reserved
[    0.000000] BIOS-e820: [mem 0x00000000000e0000-0x00000000000fffff] reserved
[    0.000000] BIOS-e820: [mem 0x0000000000100000-0x00000000ceebcfff] usable
[    0.000000] BIOS-e820: [mem 0x00000000ceebd000-0x00000000ceebefff] reserved
[    0.000000] BIOS-e820: [mem 0x00000000ceebf000-0x00000000cef08fff] usable
[    0.000000] BIOS-e820: [mem 0x00000000cef09000-0x00000000cefbefff] ACPI NVS
[    0.000000] BIOS-e820: [mem 0x00000000cefbf000-0x00000000ceff0fff] usable
[    0.000000] BIOS-e820: [mem 0x00000000ceff1000-0x00000000ceffefff] ACPI data
[    0.000000] BIOS-e820: [mem 0x00000000cefff000-0x00000000ceffffff] usable
[    0.000000] BIOS-e820: [mem 0x00000000cf000000-0x00000000cfffffff] reserved
[    0.000000] BIOS-e820: [mem 0x00000000e0000000-0x00000000e3ffffff] reserved
[    0.000000] BIOS-e820: [mem 0x00000000ffe00000-0x00000000ffffffff] reserved
[    0.000000] BIOS-e820: [mem 0x0000000100000000-0x000000012fffffff] usable
[    0.000000] NX (Execute Disable) protection: active
[    0.000000] SMBIOS 2.7 present.
[    0.000000] DMI:  /D2500CC, BIOS CCCDT10N.86A.0040.2014.0520.1400 05/20/2014
[    0.000000] e820: update [mem 0x00000000-0x00000fff] usable ==> reserved
[    0.000000] e820: remove [mem 0x000a0000-0x000fffff] usable
[    0.000000] e820: last_pfn = 0x130000 max_arch_pfn = 0x400000000
[    0.000000] MTRR default type: uncachable
[    0.000000] MTRR fixed ranges enabled:
[    0.000000]   00000-9FFFF write-back
[    0.000000]   A0000-BFFFF uncachable
[    0.000000]   C0000-DFFFF write-protect
[    0.000000]   E0000-FFFFF uncachable
[    0.000000] MTRR variable ranges enabled:
[    0.000000]   0 base 000000000 mask F80000000 write-back
[    0.000000]   1 base 080000000 mask FC0000000 write-back
[    0.000000]   2 base 0C0000000 mask FF0000000 write-back
[    0.000000]   3 base 0CF000000 mask FFF000000 uncachable
[    0.000000]   4 base 100000000 mask FC0000000 write-back
[    0.000000]   5 base 0FFE00000 mask FFFE00000 write-protect
[    0.000000]   6 disabled
[    0.000000] x86/PAT: Configuration [0-7]: WB  WC  UC- UC  WB  WC  UC- WT  
[    0.000000] e820: last_pfn = 0xcf000 max_arch_pfn = 0x400000000
[    0.000000] found SMP MP-table at [mem 0x000fbe30-0x000fbe3f] mapped at [ffff944ec00fbe30]
[    0.000000] Base memory trampoline at [ffff944ec0098000] 98000 size 24576
[    0.000000] BRK [0x12934000, 0x12934fff] PGTABLE
[    0.000000] BRK [0x12935000, 0x12935fff] PGTABLE
[    0.000000] BRK [0x12936000, 0x12936fff] PGTABLE
[    0.000000] BRK [0x12937000, 0x12937fff] PGTABLE
[    0.000000] BRK [0x12938000, 0x12938fff] PGTABLE
[    0.000000] RAMDISK: [mem 0x35675000-0x36b31fff]
[    0.000000] ACPI: Early table checksum verification disabled
[    0.000000] ACPI: RSDP 0x00000000000F2390 000024 (v02 INTEL )
[    0.000000] ACPI: XSDT 0x00000000CEFFE120 00004C (v01 INTEL  D2500CC  00000028      01000013)
[    0.000000] ACPI: FACP 0x00000000CEFF5000 0000F4 (v03 INTEL  D2500CC  00000028 MSFT 0100000D)
[    0.000000] ACPI BIOS Warning (bug): 32/64X length mismatch in FADT/Pm1aEventBlock: 32/16 (20160831/tbfadt-603)
[    0.000000] ACPI BIOS Warning (bug): 32/64X length mismatch in FADT/PmTimerBlock: 32/24 (20160831/tbfadt-603)
[    0.000000] ACPI BIOS Warning (bug): Invalid length for FADT/Pm1aEventBlock: 16, using default 32 (20160831/tbfadt-708)
[    0.000000] ACPI BIOS Warning (bug): Invalid length for FADT/PmTimerBlock: 24, using default 32 (20160831/tbfadt-708)
[    0.000000] ACPI: DSDT 0x00000000CEFF7000 0067A0 (v02 INTEL  D2500CC  00000028 MSFT 0100000D)
[    0.000000] ACPI: FACS 0x00000000CEF95000 000040
[    0.000000] ACPI: FACS 0x00000000CEF95000 000040
[    0.000000] ACPI: SSDT 0x00000000CEFF6000 00043E (v01 INTEL  D2500CC  00000028 MSFT 0100000D)
[    0.000000] ACPI: APIC 0x00000000CEFF4000 000084 (v02 INTEL  D2500CC  00000028 MSFT 0100000D)
[    0.000000] ACPI: MCFG 0x00000000CEFF3000 00003C (v01 INTEL  D2500CC  00000028 MSFT 0100000D)
[    0.000000] ACPI: HPET 0x00000000CEFF2000 000038 (v01 INTEL  D2500CC  00000028 MSFT 0100000D)
[    0.000000] ACPI: Local APIC address 0xfee00000
[    0.000000] No NUMA configuration found
[    0.000000] Faking a node at [mem 0x0000000000000000-0x000000012fffffff]
[    0.000000] NODE_DATA(0) allocated [mem 0x12fff7000-0x12fffbfff]
[    0.000000] Zone ranges:
[    0.000000]   DMA      [mem 0x0000000000001000-0x0000000000ffffff]
[    0.000000]   DMA32    [mem 0x0000000001000000-0x00000000ffffffff]
[    0.000000]   Normal   [mem 0x0000000100000000-0x000000012fffffff]
[    0.000000]   Device   empty
[    0.000000] Movable zone start for each node
[    0.000000] Early memory node ranges
[    0.000000]   node   0: [mem 0x0000000000001000-0x000000000008efff]
[    0.000000]   node   0: [mem 0x0000000000090000-0x000000000009dfff]
[    0.000000]   node   0: [mem 0x0000000000100000-0x00000000ceebcfff]
[    0.000000]   node   0: [mem 0x00000000ceebf000-0x00000000cef08fff]
[    0.000000]   node   0: [mem 0x00000000cefbf000-0x00000000ceff0fff]
[    0.000000]   node   0: [mem 0x00000000cefff000-0x00000000ceffffff]
[    0.000000]   node   0: [mem 0x0000000100000000-0x000000012fffffff]
[    0.000000] Initmem setup node 0 [mem 0x0000000000001000-0x000000012fffffff]
[    0.000000] On node 0 totalpages: 1044182
[    0.000000]   DMA zone: 64 pages used for memmap
[    0.000000]   DMA zone: 21 pages reserved
[    0.000000]   DMA zone: 3996 pages, LIFO batch:0
[    0.000000]   DMA32 zone: 13181 pages used for memmap
[    0.000000]   DMA32 zone: 843578 pages, LIFO batch:31
[    0.000000]   Normal zone: 3072 pages used for memmap
[    0.000000]   Normal zone: 196608 pages, LIFO batch:31
[    0.000000] ACPI: PM-Timer IO Port: 0x408
[    0.000000] ACPI: Local APIC address 0xfee00000
[    0.000000] ACPI: LAPIC_NMI (acpi_id[0x01] high level lint[0x1])
[    0.000000] ACPI: LAPIC_NMI (acpi_id[0x02] high level lint[0x1])
[    0.000000] ACPI: LAPIC_NMI (acpi_id[0x03] high level lint[0x1])
[    0.000000] ACPI: LAPIC_NMI (acpi_id[0x04] high level lint[0x1])
[    0.000000] IOAPIC[0]: apic_id 8, version 32, address 0xfec00000, GSI 0-23
[    0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
[    0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
[    0.000000] ACPI: IRQ0 used by override.
[    0.000000] ACPI: IRQ9 used by override.
[    0.000000] Using ACPI (MADT) for SMP configuration information
[    0.000000] ACPI: HPET id: 0x8086a201 base: 0xfed00000
[    0.000000] smpboot: Allowing 4 CPUs, 2 hotplug CPUs
[    0.000000] PM: Registered nosave memory: [mem 0x00000000-0x00000fff]
[    0.000000] PM: Registered nosave memory: [mem 0x0008f000-0x0008ffff]
[    0.000000] PM: Registered nosave memory: [mem 0x0009e000-0x0009efff]
[    0.000000] PM: Registered nosave memory: [mem 0x0009f000-0x0009ffff]
[    0.000000] PM: Registered nosave memory: [mem 0x000a0000-0x000dffff]
[    0.000000] PM: Registered nosave memory: [mem 0x000e0000-0x000fffff]
[    0.000000] PM: Registered nosave memory: [mem 0xceebd000-0xceebefff]
[    0.000000] PM: Registered nosave memory: [mem 0xcef09000-0xcefbefff]
[    0.000000] PM: Registered nosave memory: [mem 0xceff1000-0xceffefff]
[    0.000000] PM: Registered nosave memory: [mem 0xcf000000-0xcfffffff]
[    0.000000] PM: Registered nosave memory: [mem 0xd0000000-0xdfffffff]
[    0.000000] PM: Registered nosave memory: [mem 0xe0000000-0xe3ffffff]
[    0.000000] PM: Registered nosave memory: [mem 0xe4000000-0xffdfffff]
[    0.000000] PM: Registered nosave memory: [mem 0xffe00000-0xffffffff]
[    0.000000] e820: [mem 0xe4000000-0xffdfffff] available for PCI devices
[    0.000000] Booting paravirtualized kernel on bare hardware
[    0.000000] clocksource: refined-jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645519600211568 ns
[    0.000000] setup_percpu: NR_CPUS:512 nr_cpumask_bits:512 nr_cpu_ids:4 nr_node_ids:1
[    0.000000] percpu: Embedded 35 pages/cpu s105304 r8192 d29864 u524288
[    0.000000] pcpu-alloc: s105304 r8192 d29864 u524288 alloc=1*2097152
[    0.000000] pcpu-alloc: [0] 0 1 2 3 
[    0.000000] Built 1 zonelists in Node order, mobility grouping on.  Total pages: 1027844
[    0.000000] Policy zone: Normal
[    0.000000] Kernel command line: BOOT_IMAGE=/boot/vmlinuz-4.9.189-ath-regd root=UUID=903ff076-53bc-4745-a66a-34faad0960cf ro quiet vga=0x031b quiet elevator=noop ipv6.disable=1 vga=0x031b
[    0.000000] PID hash table entries: 4096 (order: 3, 32768 bytes)
[    0.000000] Calgary: detecting Calgary via BIOS EBDA area
[    0.000000] Calgary: Unable to locate Rio Grande table in EBDA - bailing!
[    0.000000] Memory: 4007644K/4176728K available (6284K kernel code, 1162K rwdata, 2848K rodata, 1424K init, 656K bss, 169084K reserved, 0K cma-reserved)
[    0.000000] Kernel/User page tables isolation: enabled
[    0.000000] Hierarchical RCU implementation.
[    0.000000] 	Build-time adjustment of leaf fanout to 64.
[    0.000000] 	RCU restricting CPUs from NR_CPUS=512 to nr_cpu_ids=4.
[    0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=64, nr_cpu_ids=4
[    0.000000] NR_IRQS:33024 nr_irqs:456 16
[    0.000000] Console: colour dummy device 80x25
[    0.000000] console [tty0] enabled
[    0.000000] clocksource: hpet: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 133484882848 ns
[    0.000000] hpet clockevent registered
[    0.000000] tsc: Fast TSC calibration using PIT
[    0.000000] tsc: Detected 1866.669 MHz processor
[    0.000052] Calibrating delay loop (skipped), value calculated using timer frequency.. 3733.33 BogoMIPS (lpj=7466676)
[    0.000058] pid_max: default: 32768 minimum: 301
[    0.000116] ACPI: Core revision 20160831
[    0.014324] ACPI: 2 ACPI AML tables successfully acquired and loaded
[    0.014487] Security Framework initialized
[    0.014490] Yama: disabled by default; enable with sysctl kernel.yama.*
[    0.014503] AppArmor: AppArmor disabled by boot time parameter
[    0.015202] Dentry cache hash table entries: 524288 (order: 10, 4194304 bytes)
[    0.018467] Inode-cache hash table entries: 262144 (order: 9, 2097152 bytes)
[    0.020022] Mount-cache hash table entries: 8192 (order: 4, 65536 bytes)
[    0.020042] Mountpoint-cache hash table entries: 8192 (order: 4, 65536 bytes)
[    0.020785] Disabled fast string operations
[    0.020796] mce: CPU supports 5 MCE banks
[    0.020808] CPU0: Thermal monitoring enabled (TM1)
[    0.020815] process: using mwait in idle threads
[    0.020822] Last level iTLB entries: 4KB 32, 2MB 0, 4MB 0
[    0.020825] Last level dTLB entries: 4KB 64, 2MB 0, 4MB 8, 1GB 0
[    0.021326] Freeing SMP alternatives memory: 24K
[    0.024385] ftrace: allocating 25339 entries in 99 pages
[    0.046870] smpboot: Max logical packages: 2
[    0.047378] ..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1
[    0.195073] smpboot: CPU0: Intel(R) Atom(TM) CPU D2500   @ 1.86GHz (family: 0x6, model: 0x36, stepping: 0x1)
[    0.195083] Performance Events: PEBS fmt0+, Atom events, 8-deep LBR, Intel PMU driver.
[    0.195104] ... version:                3
[    0.195105] ... bit width:              40
[    0.195106] ... generic registers:      2
[    0.195108] ... value mask:             000000ffffffffff
[    0.195109] ... max period:             000000007fffffff
[    0.195111] ... fixed-purpose events:   3
[    0.195112] ... event mask:             0000000700000003
[    0.196658] NMI watchdog: enabled on all CPUs, permanently consumes one hw-PMU counter.
[    0.197213] x86: Booting SMP configuration:
[    0.197216] .... node  #0, CPUs:      #1
[    0.197294] Disabled fast string operations
[    0.199465] x86: Booted up 1 node, 2 CPUs
[    0.199470] smpboot: Total of 2 processors activated (7466.67 BogoMIPS)
[    0.200748] devtmpfs: initialized
[    0.200957] x86/mm: Memory block size: 128MB
[    0.209175] PM: Registering ACPI NVS region [mem 0xcef09000-0xcefbefff] (745472 bytes)
[    0.209377] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns
[    0.209402] futex hash table entries: 1024 (order: 4, 65536 bytes)
[    0.209516] pinctrl core: initialized pinctrl subsystem
[    0.209834] NET: Registered protocol family 16
[    0.219087] cpuidle: using governor ladder
[    0.231086] cpuidle: using governor menu
[    0.231187] ACPI FADT declares the system doesn't support PCIe ASPM, so disable it
[    0.231190] ACPI: bus type PCI registered
[    0.231193] acpiphp: ACPI Hot Plug PCI Controller Driver version: 0.5
[    0.231398] PCI: MMCONFIG for domain 0000 [bus 00-3f] at [mem 0xe0000000-0xe3ffffff] (base 0xe0000000)
[    0.231402] PCI: MMCONFIG at [mem 0xe0000000-0xe3ffffff] reserved in E820
[    0.231418] PCI: Using configuration type 1 for base access
[    0.243529] HugeTLB registered 2 MB page size, pre-allocated 0 pages
[    0.244305] ACPI: Added _OSI(Module Device)
[    0.244307] ACPI: Added _OSI(Processor Device)
[    0.244309] ACPI: Added _OSI(3.0 _SCP Extensions)
[    0.244311] ACPI: Added _OSI(Processor Aggregator Device)
[    0.244674] ACPI: Executed 1 blocks of module-level executable AML code
[    0.251412] ACPI: [Firmware Bug]: BIOS _OSI(Linux) query ignored
[    0.252730] ACPI: Interpreter enabled
[    0.252779] ACPI: (supports S0 S3 S4 S5)
[    0.252782] ACPI: Using IOAPIC for interrupt routing
[    0.252870] PCI: Using host bridge windows from ACPI; if necessary, use "pci=nocrs" and report a bug
[    0.272285] ACPI: PCI Root Bridge [PCI0] (domain 0000 [bus 00-ff])
[    0.272298] acpi PNP0A08:00: _OSC: OS supports [ExtendedConfig ASPM ClockPM Segments MSI]
[    0.272422] acpi PNP0A08:00: _OSC failed (AE_ERROR); disabling ASPM
[    0.272449] acpi PNP0A08:00: [Firmware Info]: MMCONFIG for domain 0000 [bus 00-3f] only partially covers this bridge
[    0.273292] PCI host bridge to bus 0000:00
[    0.273299] pci_bus 0000:00: root bus resource [io  0x0000-0x0cf7 window]
[    0.273303] pci_bus 0000:00: root bus resource [io  0x0d00-0xffff window]
[    0.273307] pci_bus 0000:00: root bus resource [mem 0x000a0000-0x000bffff window]
[    0.273311] pci_bus 0000:00: root bus resource [mem 0x000c0000-0x000dffff window]
[    0.273314] pci_bus 0000:00: root bus resource [mem 0x000e0000-0x000effff window]
[    0.273318] pci_bus 0000:00: root bus resource [mem 0x000f0000-0x000fffff window]
[    0.273322] pci_bus 0000:00: root bus resource [mem 0xcf800000-0xcfffffff window]
[    0.273326] pci_bus 0000:00: root bus resource [mem 0xd0000000-0xfebfffff window]
[    0.273329] pci_bus 0000:00: root bus resource [mem 0xfed40000-0xfed44fff window]
[    0.273333] pci_bus 0000:00: root bus resource [bus 00-ff]
[    0.273348] pci 0000:00:00.0: [8086:0bf5] type 00 class 0x060000
[    0.273617] pci 0000:00:02.0: [8086:0be1] type 00 class 0x030000
[    0.273632] pci 0000:00:02.0: reg 0x10: [mem 0xd0700000-0xd07fffff]
[    0.273640] pci 0000:00:02.0: reg 0x14: [io  0x40d0-0x40d7]
[    0.273932] pci 0000:00:1c.0: [8086:27d0] type 01 class 0x060400
[    0.274045] pci 0000:00:1c.0: PME# supported from D0 D3hot D3cold
[    0.274175] pci 0000:00:1c.0: System wakeup disabled by ACPI
[    0.274297] pci 0000:00:1c.1: [8086:27d2] type 01 class 0x060400
[    0.274408] pci 0000:00:1c.1: PME# supported from D0 D3hot D3cold
[    0.274536] pci 0000:00:1c.1: System wakeup disabled by ACPI
[    0.274655] pci 0000:00:1c.2: [8086:27d4] type 01 class 0x060400
[    0.274765] pci 0000:00:1c.2: PME# supported from D0 D3hot D3cold
[    0.274892] pci 0000:00:1c.2: System wakeup disabled by ACPI
[    0.275014] pci 0000:00:1d.0: [8086:27c8] type 00 class 0x0c0300
[    0.275070] pci 0000:00:1d.0: reg 0x20: [io  0x40a0-0x40bf]
[    0.275288] pci 0000:00:1d.0: System wakeup disabled by ACPI
[    0.275409] pci 0000:00:1d.1: [8086:27c9] type 00 class 0x0c0300
[    0.275464] pci 0000:00:1d.1: reg 0x20: [io  0x4080-0x409f]
[    0.275653] pci 0000:00:1d.1: System wakeup disabled by ACPI
[    0.275770] pci 0000:00:1d.2: [8086:27ca] type 00 class 0x0c0300
[    0.275826] pci 0000:00:1d.2: reg 0x20: [io  0x4060-0x407f]
[    0.276016] pci 0000:00:1d.2: System wakeup disabled by ACPI
[    0.276132] pci 0000:00:1d.3: [8086:27cb] type 00 class 0x0c0300
[    0.276188] pci 0000:00:1d.3: reg 0x20: [io  0x4040-0x405f]
[    0.276380] pci 0000:00:1d.3: System wakeup disabled by ACPI
[    0.276508] pci 0000:00:1d.7: [8086:27cc] type 00 class 0x0c0320
[    0.276533] pci 0000:00:1d.7: reg 0x10: [mem 0xd0800400-0xd08007ff]
[    0.276646] pci 0000:00:1d.7: PME# supported from D0 D3hot D3cold
[    0.276801] pci 0000:00:1d.7: System wakeup disabled by ACPI
[    0.276921] pci 0000:00:1e.0: [8086:2448] type 01 class 0x060401
[    0.277197] pci 0000:00:1f.0: [8086:27bc] type 00 class 0x060100
[    0.277303] pci 0000:00:1f.0: [Firmware Bug]: TigerPoint LPC.BM_STS cleared
[    0.277543] pci 0000:00:1f.2: [8086:27c1] type 00 class 0x010601
[    0.277565] pci 0000:00:1f.2: reg 0x10: [io  0x40c8-0x40cf]
[    0.277577] pci 0000:00:1f.2: reg 0x14: [io  0x40dc-0x40df]
[    0.277588] pci 0000:00:1f.2: reg 0x18: [io  0x40c0-0x40c7]
[    0.277600] pci 0000:00:1f.2: reg 0x1c: [io  0x40d8-0x40db]
[    0.277612] pci 0000:00:1f.2: reg 0x20: [io  0x4020-0x402f]
[    0.277624] pci 0000:00:1f.2: reg 0x24: [mem 0xd0800000-0xd08003ff]
[    0.277682] pci 0000:00:1f.2: PME# supported from D3hot
[    0.277911] pci 0000:00:1f.3: [8086:27da] type 00 class 0x0c0500
[    0.277977] pci 0000:00:1f.3: reg 0x20: [io  0x4000-0x401f]
[    0.278379] pci 0000:02:00.0: [8086:10d3] type 00 class 0x020000
[    0.278417] pci 0000:02:00.0: reg 0x10: [mem 0xd0620000-0xd063ffff]
[    0.278438] pci 0000:02:00.0: reg 0x14: [mem 0xd0600000-0xd061ffff]
[    0.278459] pci 0000:02:00.0: reg 0x18: [io  0x3000-0x301f]
[    0.278481] pci 0000:02:00.0: reg 0x1c: [mem 0xd0640000-0xd0643fff]
[    0.278666] pci 0000:02:00.0: PME# supported from D0 D3hot D3cold
[    0.278752] pci 0000:02:00.0: System wakeup disabled by ACPI
[    0.287110] pci 0000:00:1c.0: PCI bridge to [bus 02]
[    0.287117] pci 0000:00:1c.0:   bridge window [io  0x3000-0x3fff]
[    0.287123] pci 0000:00:1c.0:   bridge window [mem 0xd0600000-0xd06fffff]
[    0.287292] pci 0000:01:00.0: [8086:10d3] type 00 class 0x020000
[    0.287329] pci 0000:01:00.0: reg 0x10: [mem 0xd0520000-0xd053ffff]
[    0.287351] pci 0000:01:00.0: reg 0x14: [mem 0xd0500000-0xd051ffff]
[    0.287372] pci 0000:01:00.0: reg 0x18: [io  0x2000-0x201f]
[    0.287394] pci 0000:01:00.0: reg 0x1c: [mem 0xd0540000-0xd0543fff]
[    0.287580] pci 0000:01:00.0: PME# supported from D0 D3hot D3cold
[    0.287667] pci 0000:01:00.0: System wakeup disabled by ACPI
[    0.299105] pci 0000:00:1c.1: PCI bridge to [bus 01]
[    0.299112] pci 0000:00:1c.1:   bridge window [io  0x2000-0x2fff]
[    0.299118] pci 0000:00:1c.1:   bridge window [mem 0xd0500000-0xd05fffff]
[    0.299277] pci 0000:03:00.0: [168c:003c] type 00 class 0x028000
[    0.299312] pci 0000:03:00.0: reg 0x10: [mem 0xd0000000-0xd01fffff 64bit]
[    0.299377] pci 0000:03:00.0: reg 0x30: [mem 0xffff0000-0xffffffff pref]
[    0.299477] pci 0000:03:00.0: supports D1 D2
[    0.299549] pci 0000:03:00.0: System wakeup disabled by ACPI
[    0.311102] pci 0000:00:1c.2: PCI bridge to [bus 03]
[    0.311112] pci 0000:00:1c.2:   bridge window [mem 0xd0000000-0xd01fffff]
[    0.311246] pci 0000:04:00.0: [1011:0024] type 01 class 0x060400
[    0.311382] pci 0000:04:00.0: System wakeup disabled by ACPI
[    0.311533] pci 0000:00:1e.0: PCI bridge to [bus 04-05] (subtractive decode)
[    0.311539] pci 0000:00:1e.0:   bridge window [io  0x1000-0x1fff]
[    0.311545] pci 0000:00:1e.0:   bridge window [mem 0xd0300000-0xd04fffff]
[    0.311554] pci 0000:00:1e.0:   bridge window [mem 0xd0200000-0xd02fffff 64bit pref]
[    0.311559] pci 0000:00:1e.0:   bridge window [io  0x0000-0x0cf7 window] (subtractive decode)
[    0.311563] pci 0000:00:1e.0:   bridge window [io  0x0d00-0xffff window] (subtractive decode)
[    0.311566] pci 0000:00:1e.0:   bridge window [mem 0x000a0000-0x000bffff window] (subtractive decode)
[    0.311570] pci 0000:00:1e.0:   bridge window [mem 0x000c0000-0x000dffff window] (subtractive decode)
[    0.311574] pci 0000:00:1e.0:   bridge window [mem 0x000e0000-0x000effff window] (subtractive decode)
[    0.311578] pci 0000:00:1e.0:   bridge window [mem 0x000f0000-0x000fffff window] (subtractive decode)
[    0.311582] pci 0000:00:1e.0:   bridge window [mem 0xcf800000-0xcfffffff window] (subtractive decode)
[    0.311585] pci 0000:00:1e.0:   bridge window [mem 0xd0000000-0xfebfffff window] (subtractive decode)
[    0.311589] pci 0000:00:1e.0:   bridge window [mem 0xfed40000-0xfed44fff window] (subtractive decode)
[    0.311693] pci 0000:05:04.0: [8086:1229] type 00 class 0x020000
[    0.311721] pci 0000:05:04.0: reg 0x10: [mem 0xd0201000-0xd0201fff pref]
[    0.311737] pci 0000:05:04.0: reg 0x14: [io  0x1020-0x103f]
[    0.311753] pci 0000:05:04.0: reg 0x18: [mem 0xd0400000-0xd04fffff]
[    0.311805] pci 0000:05:04.0: reg 0x30: [mem 0xfff00000-0xffffffff pref]
[    0.311866] pci 0000:05:04.0: supports D1 D2
[    0.311869] pci 0000:05:04.0: PME# supported from D0 D1 D2 D3hot
[    0.312005] pci 0000:05:05.0: [8086:1229] type 00 class 0x020000
[    0.312033] pci 0000:05:05.0: reg 0x10: [mem 0xd0200000-0xd0200fff pref]
[    0.312049] pci 0000:05:05.0: reg 0x14: [io  0x1000-0x101f]
[    0.312064] pci 0000:05:05.0: reg 0x18: [mem 0xd0300000-0xd03fffff]
[    0.312116] pci 0000:05:05.0: reg 0x30: [mem 0xfff00000-0xffffffff pref]
[    0.312176] pci 0000:05:05.0: supports D1 D2
[    0.312179] pci 0000:05:05.0: PME# supported from D0 D1 D2 D3hot
[    0.312347] pci 0000:04:00.0: PCI bridge to [bus 05]
[    0.312357] pci 0000:04:00.0:   bridge window [io  0x1000-0x1fff]
[    0.312364] pci 0000:04:00.0:   bridge window [mem 0xd0300000-0xd04fffff]
[    0.312373] pci 0000:04:00.0:   bridge window [mem 0xd0200000-0xd02fffff 64bit pref]
[    0.313997] ACPI: PCI Interrupt Link [LNKA] (IRQs 1 3 4 5 6 7 10 12 14 15) *11
[    0.314181] ACPI: PCI Interrupt Link [LNKB] (IRQs 1 3 4 5 6 7 11 12 14 15) *9
[    0.314361] ACPI: PCI Interrupt Link [LNKC] (IRQs 1 3 4 5 6 7 *10 12 14 15)
[    0.314539] ACPI: PCI Interrupt Link [LNKD] (IRQs 1 3 4 5 6 7 11 12 14 15) *9
[    0.314719] ACPI: PCI Interrupt Link [LNKE] (IRQs 1 3 4 5 6 7 *10 12 14 15)
[    0.314898] ACPI: PCI Interrupt Link [LNKF] (IRQs 1 3 4 5 6 7 *11 12 14 15)
[    0.315099] ACPI: PCI Interrupt Link [LNKG] (IRQs 1 3 4 5 6 7 10 12 14 15) *0, disabled.
[    0.315282] ACPI: PCI Interrupt Link [LNKH] (IRQs 1 3 4 5 6 7 *11 12 14 15)
[    0.315677] ACPI: Enabled 6 GPEs in block 00 to 1F
[    0.315995] vgaarb: setting as boot device: PCI:0000:00:02.0
[    0.315999] vgaarb: device added: PCI:0000:00:02.0,decodes=io+mem,owns=io+mem,locks=none
[    0.316009] vgaarb: loaded
[    0.316011] vgaarb: bridge control possible 0000:00:02.0
[    0.316266] PCI: Using ACPI for IRQ routing
[    0.318182] PCI: pci_cache_line_size set to 64 bytes
[    0.318276] e820: reserve RAM buffer [mem 0x0008f000-0x0008ffff]
[    0.318280] e820: reserve RAM buffer [mem 0x0009e800-0x0009ffff]
[    0.318283] e820: reserve RAM buffer [mem 0xceebd000-0xcfffffff]
[    0.318286] e820: reserve RAM buffer [mem 0xcef09000-0xcfffffff]
[    0.318288] e820: reserve RAM buffer [mem 0xceff1000-0xcfffffff]
[    0.318291] e820: reserve RAM buffer [mem 0xcf000000-0xcfffffff]
[    0.318770] hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0
[    0.318779] hpet0: 3 comparators, 64-bit 14.318180 MHz counter
[    0.320846] clocksource: Switched to clocksource hpet
[    0.343899] VFS: Disk quotas dquot_6.6.0
[    0.343963] VFS: Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
[    0.344214] pnp: PnP ACPI init
[    0.344661] system 00:00: [mem 0xfed00000-0xfed003ff] has been reserved
[    0.344672] system 00:00: Plug and Play ACPI device, IDs PNP0103 PNP0c01 (active)
[    0.344874] system 00:01: [io  0x0680-0x069f] has been reserved
[    0.344882] system 00:01: [io  0xffff] has been reserved
[    0.344886] system 00:01: [io  0xffff] has been reserved
[    0.344890] system 00:01: [io  0xffff] has been reserved
[    0.344895] system 00:01: [io  0x0400-0x047f] has been reserved
[    0.344899] system 00:01: [io  0x0500-0x057f] has been reserved
[    0.344903] system 00:01: [io  0x0600-0x061f] has been reserved
[    0.344911] system 00:01: Plug and Play ACPI device, IDs PNP0c02 (active)
[    0.345090] system 00:02: [io  0x06a0-0x06af] has been reserved
[    0.345095] system 00:02: [io  0x06b0-0x06ff] has been reserved
[    0.345101] system 00:02: Plug and Play ACPI device, IDs PNP0c02 (active)
[    0.345201] pnp 00:03: Plug and Play ACPI device, IDs PNP0b00 (active)
[    0.346099] ACPI: IRQ 3 override to edge, high
[    0.346257] pnp 00:04: Plug and Play ACPI device, IDs PNP0501 (active)
[    0.346629] ACPI: IRQ 4 override to edge, high
[    0.346785] pnp 00:05: Plug and Play ACPI device, IDs PNP0501 (active)
[    0.347223] system 00:06: [mem 0xfed1c000-0xfed1ffff] has been reserved
[    0.347229] system 00:06: [mem 0x00000000-0x00003fff] could not be reserved
[    0.347233] system 00:06: [mem 0x00000000-0x00000fff] could not be reserved
[    0.347238] system 00:06: [mem 0x00000000-0x00000fff] could not be reserved
[    0.347242] system 00:06: [mem 0xfed45000-0xfed8ffff] has been reserved
[    0.347250] system 00:06: Plug and Play ACPI device, IDs PNP0c02 (active)
[    0.347627] pnp: PnP ACPI: found 7 devices
[    0.358239] clocksource: acpi_pm: mask: 0xffffff max_cycles: 0xffffff, max_idle_ns: 2085701024 ns
[    0.358254] pci 0000:03:00.0: can't claim BAR 6 [mem 0xffff0000-0xffffffff pref]: no compatible bridge window
[    0.358261] pci 0000:05:04.0: can't claim BAR 6 [mem 0xfff00000-0xffffffff pref]: no compatible bridge window
[    0.358266] pci 0000:05:05.0: can't claim BAR 6 [mem 0xfff00000-0xffffffff pref]: no compatible bridge window
[    0.358297] pci 0000:00:1c.0: bridge window [mem 0x00100000-0x000fffff 64bit pref] to [bus 02] add_size 200000 add_align 100000
[    0.358312] pci 0000:00:1c.1: bridge window [mem 0x00100000-0x000fffff 64bit pref] to [bus 01] add_size 200000 add_align 100000
[    0.358325] pci 0000:00:1c.2: bridge window [io  0x1000-0x0fff] to [bus 03] add_size 1000
[    0.358331] pci 0000:00:1c.2: bridge window [mem 0x00100000-0x000fffff 64bit pref] to [bus 03] add_size 200000 add_align 100000
[    0.358371] pci 0000:00:1c.0: res[15]=[mem 0x00100000-0x000fffff 64bit pref] res_to_dev_res add_size 200000 min_align 100000
[    0.358375] pci 0000:00:1c.0: res[15]=[mem 0x00100000-0x002fffff 64bit pref] res_to_dev_res add_size 200000 min_align 100000
[    0.358379] pci 0000:00:1c.1: res[15]=[mem 0x00100000-0x000fffff 64bit pref] res_to_dev_res add_size 200000 min_align 100000
[    0.358383] pci 0000:00:1c.1: res[15]=[mem 0x00100000-0x002fffff 64bit pref] res_to_dev_res add_size 200000 min_align 100000
[    0.358388] pci 0000:00:1c.2: res[15]=[mem 0x00100000-0x000fffff 64bit pref] res_to_dev_res add_size 200000 min_align 100000
[    0.358392] pci 0000:00:1c.2: res[15]=[mem 0x00100000-0x002fffff 64bit pref] res_to_dev_res add_size 200000 min_align 100000
[    0.358396] pci 0000:00:1c.2: res[13]=[io  0x1000-0x0fff] res_to_dev_res add_size 1000 min_align 1000
[    0.358400] pci 0000:00:1c.2: res[13]=[io  0x1000-0x1fff] res_to_dev_res add_size 1000 min_align 1000
[    0.358418] pci 0000:00:1c.0: BAR 15: assigned [mem 0xd0900000-0xd0afffff 64bit pref]
[    0.358431] pci 0000:00:1c.1: BAR 15: assigned [mem 0xd0b00000-0xd0cfffff 64bit pref]
[    0.358443] pci 0000:00:1c.2: BAR 15: assigned [mem 0xd0d00000-0xd0efffff 64bit pref]
[    0.358449] pci 0000:00:1c.2: BAR 13: assigned [io  0x5000-0x5fff]
[    0.358456] pci 0000:00:1c.0: PCI bridge to [bus 02]
[    0.358461] pci 0000:00:1c.0:   bridge window [io  0x3000-0x3fff]
[    0.358468] pci 0000:00:1c.0:   bridge window [mem 0xd0600000-0xd06fffff]
[    0.358475] pci 0000:00:1c.0:   bridge window [mem 0xd0900000-0xd0afffff 64bit pref]
[    0.358483] pci 0000:00:1c.1: PCI bridge to [bus 01]
[    0.358488] pci 0000:00:1c.1:   bridge window [io  0x2000-0x2fff]
[    0.358495] pci 0000:00:1c.1:   bridge window [mem 0xd0500000-0xd05fffff]
[    0.358501] pci 0000:00:1c.1:   bridge window [mem 0xd0b00000-0xd0cfffff 64bit pref]
[    0.358513] pci 0000:03:00.0: BAR 6: assigned [mem 0xd0d00000-0xd0d0ffff pref]
[    0.358517] pci 0000:00:1c.2: PCI bridge to [bus 03]
[    0.358521] pci 0000:00:1c.2:   bridge window [io  0x5000-0x5fff]
[    0.358528] pci 0000:00:1c.2:   bridge window [mem 0xd0000000-0xd01fffff]
[    0.358534] pci 0000:00:1c.2:   bridge window [mem 0xd0d00000-0xd0efffff 64bit pref]
[    0.358548] pci 0000:05:04.0: BAR 6: no space for [mem size 0x00100000 pref]
[    0.358552] pci 0000:05:04.0: BAR 6: failed to assign [mem size 0x00100000 pref]
[    0.358557] pci 0000:05:05.0: BAR 6: no space for [mem size 0x00100000 pref]
[    0.358560] pci 0000:05:05.0: BAR 6: failed to assign [mem size 0x00100000 pref]
[    0.358564] pci 0000:04:00.0: PCI bridge to [bus 05]
[    0.358569] pci 0000:04:00.0:   bridge window [io  0x1000-0x1fff]
[    0.358577] pci 0000:04:00.0:   bridge window [mem 0xd0300000-0xd04fffff]
[    0.358583] pci 0000:04:00.0:   bridge window [mem 0xd0200000-0xd02fffff 64bit pref]
[    0.358592] pci 0000:00:1e.0: PCI bridge to [bus 04-05]
[    0.358597] pci 0000:00:1e.0:   bridge window [io  0x1000-0x1fff]
[    0.358603] pci 0000:00:1e.0:   bridge window [mem 0xd0300000-0xd04fffff]
[    0.358609] pci 0000:00:1e.0:   bridge window [mem 0xd0200000-0xd02fffff 64bit pref]
[    0.358619] pci_bus 0000:00: resource 4 [io  0x0000-0x0cf7 window]
[    0.358622] pci_bus 0000:00: resource 5 [io  0x0d00-0xffff window]
[    0.358626] pci_bus 0000:00: resource 6 [mem 0x000a0000-0x000bffff window]
[    0.358629] pci_bus 0000:00: resource 7 [mem 0x000c0000-0x000dffff window]
[    0.358633] pci_bus 0000:00: resource 8 [mem 0x000e0000-0x000effff window]
[    0.358636] pci_bus 0000:00: resource 9 [mem 0x000f0000-0x000fffff window]
[    0.358640] pci_bus 0000:00: resource 10 [mem 0xcf800000-0xcfffffff window]
[    0.358643] pci_bus 0000:00: resource 11 [mem 0xd0000000-0xfebfffff window]
[    0.358647] pci_bus 0000:00: resource 12 [mem 0xfed40000-0xfed44fff window]
[    0.358650] pci_bus 0000:02: resource 0 [io  0x3000-0x3fff]
[    0.358654] pci_bus 0000:02: resource 1 [mem 0xd0600000-0xd06fffff]
[    0.358657] pci_bus 0000:02: resource 2 [mem 0xd0900000-0xd0afffff 64bit pref]
[    0.358661] pci_bus 0000:01: resource 0 [io  0x2000-0x2fff]
[    0.358664] pci_bus 0000:01: resource 1 [mem 0xd0500000-0xd05fffff]
[    0.358668] pci_bus 0000:01: resource 2 [mem 0xd0b00000-0xd0cfffff 64bit pref]
[    0.358671] pci_bus 0000:03: resource 0 [io  0x5000-0x5fff]
[    0.358674] pci_bus 0000:03: resource 1 [mem 0xd0000000-0xd01fffff]
[    0.358678] pci_bus 0000:03: resource 2 [mem 0xd0d00000-0xd0efffff 64bit pref]
[    0.358681] pci_bus 0000:04: resource 0 [io  0x1000-0x1fff]
[    0.358685] pci_bus 0000:04: resource 1 [mem 0xd0300000-0xd04fffff]
[    0.358688] pci_bus 0000:04: resource 2 [mem 0xd0200000-0xd02fffff 64bit pref]
[    0.358691] pci_bus 0000:04: resource 4 [io  0x0000-0x0cf7 window]
[    0.358695] pci_bus 0000:04: resource 5 [io  0x0d00-0xffff window]
[    0.358698] pci_bus 0000:04: resource 6 [mem 0x000a0000-0x000bffff window]
[    0.358702] pci_bus 0000:04: resource 7 [mem 0x000c0000-0x000dffff window]
[    0.358705] pci_bus 0000:04: resource 8 [mem 0x000e0000-0x000effff window]
[    0.358708] pci_bus 0000:04: resource 9 [mem 0x000f0000-0x000fffff window]
[    0.358712] pci_bus 0000:04: resource 10 [mem 0xcf800000-0xcfffffff window]
[    0.358715] pci_bus 0000:04: resource 11 [mem 0xd0000000-0xfebfffff window]
[    0.358719] pci_bus 0000:04: resource 12 [mem 0xfed40000-0xfed44fff window]
[    0.358722] pci_bus 0000:05: resource 0 [io  0x1000-0x1fff]
[    0.358726] pci_bus 0000:05: resource 1 [mem 0xd0300000-0xd04fffff]
[    0.358729] pci_bus 0000:05: resource 2 [mem 0xd0200000-0xd02fffff 64bit pref]
[    0.359012] NET: Registered protocol family 2
[    0.359480] TCP established hash table entries: 32768 (order: 6, 262144 bytes)
[    0.359725] TCP bind hash table entries: 32768 (order: 7, 524288 bytes)
[    0.360026] TCP: Hash tables configured (established 32768 bind 32768)
[    0.360180] UDP hash table entries: 2048 (order: 4, 65536 bytes)
[    0.360236] UDP-Lite hash table entries: 2048 (order: 4, 65536 bytes)
[    0.360458] NET: Registered protocol family 1
[    0.360498] pci 0000:00:02.0: Video device with shadowed ROM at [mem 0x000c0000-0x000dffff]
[    0.361878] pci 0000:05:04.0: Firmware left e100 interrupts enabled; disabling
[    0.361901] pci 0000:05:05.0: Firmware left e100 interrupts enabled; disabling
[    0.361909] PCI: CLS 64 bytes, default 64
[    0.362049] Unpacking initramfs...
[    1.111208] Freeing initrd memory: 21236K
[    1.113526] PCI-DMA: Using software bounce buffering for IO (SWIOTLB)
[    1.113531] software IO TLB: mapped [mem 0xcaebd000-0xceebd000] (64MB)
[    1.114527] audit: initializing netlink subsys (disabled)
[    1.114571] audit: type=2000 audit(1576172903.004:1): initialized
[    1.115583] workingset: timestamp_bits=40 max_order=20 bucket_order=0
[    1.115645] zbud: loaded
[    1.117509] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 250)
[    1.117594] io scheduler noop registered (default)
[    1.117596] io scheduler deadline registered
[    1.117626] io scheduler cfq registered
[    1.118848] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[    1.118869] pciehp: PCI Express Hot Plug Controller Driver version: 0.4
[    1.118902] vesafb: mode is 1280x1024x32, linelength=5120, pages=0
[    1.118904] vesafb: scrolling: redraw
[    1.118908] vesafb: Truecolor: size=8:8:8:8, shift=24:16:8:0
[    1.118925] pmd_set_huge: Cannot satisfy [mem 0xcf800000-0xcfa00000] with a huge-page mapping due to MTRR override.
[    1.118962] vesafb: framebuffer at 0xcf800000, mapped to 0xffffbdb201000000, using 5120k, total 5120k
[    1.160190] Console: switching to colour frame buffer device 160x64
[    1.201052] fb0: VESA VGA frame buffer device
[    1.201101] intel_idle: MWAIT substates: 0x10
[    1.201103] intel_idle: v0.4.1 model 0x36
[    1.201219] intel_idle: lapic_timer_reliable_states 0xffffffff
[    1.201463] GHES: HEST is not enabled!
[    1.201632] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
[    1.222297] 00:04: ttyS0 at I/O 0x3f8 (irq = 3, base_baud = 115200) is a 16550A
[    1.243118] 00:05: ttyS1 at I/O 0x2f8 (irq = 4, base_baud = 115200) is a 16550A
[    1.244168] Linux agpgart interface v0.103
[    1.244403] AMD IOMMUv2 driver by Joerg Roedel <jroedel@suse.de>
[    1.244405] AMD IOMMUv2 functionality not available on this system
[    1.244956] i8042: PNP: No PS/2 controller found. Probing ports directly.
[    1.247415] serio: i8042 KBD port at 0x60,0x64 irq 1
[    1.247429] serio: i8042 AUX port at 0x60,0x64 irq 12
[    1.247859] mousedev: PS/2 mouse device common for all mice
[    1.247948] rtc_cmos 00:03: RTC can wake from S4
[    1.248210] rtc_cmos 00:03: rtc core: registered rtc_cmos as rtc0
[    1.248251] rtc_cmos 00:03: alarms up to one month, y3k, 242 bytes nvram, hpet irqs
[    1.248326] ledtrig-cpu: registered to indicate activity on CPUs
[    1.249159] IPv6: Loaded, but administratively disabled, reboot required to enable
[    1.249161] mip6: Mobile IPv6
[    1.249163] mip6: mip6_init: can't add xfrm type(destopt)
[    1.249166] NET: Registered protocol family 17
[    1.249178] mpls_gso: MPLS GSO support
[    1.249631] microcode: sig=0x30661, pf=0x4, revision=0x10d
[    1.249736] microcode: Microcode Update Driver: v2.01 <tigran@aivazian.fsnet.co.uk>, Peter Oruba
[    1.250087] registered taskstats version 1
[    1.250127] zswap: loaded using pool lzo/zbud
[    1.250285] ima: No TPM chip found, activating TPM-bypass!
[    1.250290] ima: Allocated hash algorithm: sha256
[    1.251081] rtc_cmos 00:03: setting system clock to 2019-12-12 17:48:24 UTC (1576172904)
[    1.251251] PM: Hibernation image not present or could not be loaded.
[    1.254130] Freeing unused kernel memory: 1424K
[    1.254135] Write protecting the kernel read-only data: 12288k
[    1.256200] Freeing unused kernel memory: 1892K
[    1.264991] Freeing unused kernel memory: 1248K
[    1.279586] x86/mm: Checked W+X mappings: passed, no W+X pages found.
[    1.320614] udevd[70]: starting version 3.2.2
[    1.321469] random: udevd: uninitialized urandom read (16 bytes read)
[    1.321574] random: udevd: uninitialized urandom read (16 bytes read)
[    1.323765] udevd[71]: starting eudev-3.2.2
[    1.347080] random: udevd: uninitialized urandom read (16 bytes read)
[    1.382182] pps_core: LinuxPPS API ver. 1 registered
[    1.382185] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[    1.382745] PTP clock support registered
[    1.385480] e1000e: Intel(R) PRO/1000 Network Driver - 3.2.6-k
[    1.385483] e1000e: Copyright(c) 1999 - 2015 Intel Corporation.
[    1.385799] e1000e 0000:02:00.0: Interrupt Throttling Rate (ints/sec) set to dynamic conservative mode
[    1.393325] ACPI: bus type USB registered
[    1.393396] usbcore: registered new interface driver usbfs
[    1.393428] usbcore: registered new interface driver hub
[    1.393501] usbcore: registered new device driver usb
[    1.394795] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    1.395719] uhci_hcd: USB Universal Host Controller Interface driver
[    1.396016] uhci_hcd 0000:00:1d.0: UHCI Host Controller
[    1.396031] uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 1
[    1.396049] uhci_hcd 0000:00:1d.0: detected 2 ports
[    1.396100] uhci_hcd 0000:00:1d.0: irq 23, io base 0x000040a0
[    1.396291] usb usb1: New USB device found, idVendor=1d6b, idProduct=0001
[    1.396295] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    1.396298] usb usb1: Product: UHCI Host Controller
[    1.396301] usb usb1: Manufacturer: Linux 4.9.189-ath-regd uhci_hcd
[    1.396304] usb usb1: SerialNumber: 0000:00:1d.0
[    1.396688] hub 1-0:1.0: USB hub found
[    1.396709] hub 1-0:1.0: 2 ports detected
[    1.397324] uhci_hcd 0000:00:1d.1: UHCI Host Controller
[    1.397340] uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 2
[    1.397353] uhci_hcd 0000:00:1d.1: detected 2 ports
[    1.397401] uhci_hcd 0000:00:1d.1: irq 19, io base 0x00004080
[    1.397558] usb usb2: New USB device found, idVendor=1d6b, idProduct=0001
[    1.397562] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    1.397565] usb usb2: Product: UHCI Host Controller
[    1.397568] usb usb2: Manufacturer: Linux 4.9.189-ath-regd uhci_hcd
[    1.397571] usb usb2: SerialNumber: 0000:00:1d.1
[    1.397940] hub 2-0:1.0: USB hub found
[    1.397959] hub 2-0:1.0: 2 ports detected
[    1.398383] ehci-pci: EHCI PCI platform driver
[    1.398594] uhci_hcd 0000:00:1d.2: UHCI Host Controller
[    1.398610] uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 3
[    1.398626] uhci_hcd 0000:00:1d.2: detected 2 ports
[    1.398675] uhci_hcd 0000:00:1d.2: irq 18, io base 0x00004060
[    1.398832] usb usb3: New USB device found, idVendor=1d6b, idProduct=0001
[    1.398837] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    1.398840] usb usb3: Product: UHCI Host Controller
[    1.398843] usb usb3: Manufacturer: Linux 4.9.189-ath-regd uhci_hcd
[    1.398845] usb usb3: SerialNumber: 0000:00:1d.2
[    1.399208] hub 3-0:1.0: USB hub found
[    1.399227] hub 3-0:1.0: 2 ports detected
[    1.399741] uhci_hcd 0000:00:1d.3: UHCI Host Controller
[    1.399760] uhci_hcd 0000:00:1d.3: new USB bus registered, assigned bus number 4
[    1.399772] uhci_hcd 0000:00:1d.3: detected 2 ports
[    1.399822] uhci_hcd 0000:00:1d.3: irq 16, io base 0x00004040
[    1.399972] usb usb4: New USB device found, idVendor=1d6b, idProduct=0001
[    1.399976] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    1.399979] usb usb4: Product: UHCI Host Controller
[    1.399982] usb usb4: Manufacturer: Linux 4.9.189-ath-regd uhci_hcd
[    1.399985] usb usb4: SerialNumber: 0000:00:1d.3
[    1.400349] hub 4-0:1.0: USB hub found
[    1.400367] hub 4-0:1.0: 2 ports detected
[    1.401593] e100: Intel(R) PRO/100 Network Driver, 3.5.24-k2-NAPI
[    1.401596] e100: Copyright(c) 1999-2006 Intel Corporation
[    1.402425] ehci-pci 0000:00:1d.7: EHCI Host Controller
[    1.402442] ehci-pci 0000:00:1d.7: new USB bus registered, assigned bus number 5
[    1.402467] ehci-pci 0000:00:1d.7: debug port 1
[    1.406391] ehci-pci 0000:00:1d.7: cache line size of 64 is not supported
[    1.406484] ehci-pci 0000:00:1d.7: irq 23, io mem 0xd0800400
[    1.413998] SCSI subsystem initialized
[    1.420929] ehci-pci 0000:00:1d.7: USB 2.0 started, EHCI 1.00
[    1.421071] usb usb5: New USB device found, idVendor=1d6b, idProduct=0002
[    1.421075] usb usb5: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    1.421078] usb usb5: Product: EHCI Host Controller
[    1.421081] usb usb5: Manufacturer: Linux 4.9.189-ath-regd ehci_hcd
[    1.421084] usb usb5: SerialNumber: 0000:00:1d.7
[    1.421462] hub 5-0:1.0: USB hub found
[    1.421482] hub 5-0:1.0: 8 ports detected
[    1.431547] libata version 3.00 loaded.
[    1.431838] e100 0000:05:04.0 eth0: addr 0xd0201000, irq 20, MAC addr 00:50:8b:66:35:a8
[    1.441645] e1000e 0000:02:00.0 0000:02:00.0 (uninitialized): registered PHC clock
[    1.449096] hub 1-0:1.0: USB hub found
[    1.449119] hub 1-0:1.0: 2 ports detected
[    1.462948] e100 0000:05:05.0 eth1: addr 0xd0200000, irq 21, MAC addr 00:50:8b:66:35:a9
[    1.477091] hub 2-0:1.0: USB hub found
[    1.477114] hub 2-0:1.0: 2 ports detected
[    1.503108] e1000e 0000:02:00.0 eth2: (PCI Express:2.5GT/s:Width x1) 00:22:4d:a6:e2:25
[    1.503112] e1000e 0000:02:00.0 eth2: Intel(R) PRO/1000 Network Connection
[    1.503129] e1000e 0000:02:00.0 eth2: MAC: 3, PHY: 8, PBA No: FFFFFF-0FF
[    1.503411] e1000e 0000:01:00.0: Interrupt Throttling Rate (ints/sec) set to dynamic conservative mode
[    1.505174] hub 3-0:1.0: USB hub found
[    1.505200] hub 3-0:1.0: 2 ports detected
[    1.533128] hub 4-0:1.0: USB hub found
[    1.533151] hub 4-0:1.0: 2 ports detected
[    1.534023] i801_smbus 0000:00:1f.3: SMBus using PCI interrupt
[    1.535811] ahci 0000:00:1f.2: version 3.0
[    1.536098] ahci 0000:00:1f.2: SSS flag set, parallel bus scan disabled
[    1.536138] ahci 0000:00:1f.2: AHCI 0001.0100 32 slots 4 ports 3 Gbps 0x3 impl SATA mode
[    1.536144] ahci 0000:00:1f.2: flags: 64bit ncq stag pm led clo pio slum part 
[    1.538005] scsi host0: ahci
[    1.538342] scsi host1: ahci
[    1.538632] scsi host2: ahci
[    1.538928] scsi host3: ahci
[    1.539089] ata1: SATA max UDMA/133 abar m1024@0xd0800000 port 0xd0800100 irq 33
[    1.539093] ata2: SATA max UDMA/133 abar m1024@0xd0800000 port 0xd0800180 irq 33
[    1.539095] ata3: DUMMY
[    1.539097] ata4: DUMMY
[    1.557524] e1000e 0000:01:00.0 0000:01:00.0 (uninitialized): registered PHC clock
[    1.620132] e1000e 0000:01:00.0 eth3: (PCI Express:2.5GT/s:Width x1) 00:22:4d:a6:e2:29
[    1.620136] e1000e 0000:01:00.0 eth3: Intel(R) PRO/1000 Network Connection
[    1.620152] e1000e 0000:01:00.0 eth3: MAC: 3, PHY: 8, PBA No: FFFFFF-0FF
[    1.851348] ata1: SATA link down (SStatus 0 SControl 300)
[    2.124931] tsc: Refined TSC clocksource calibration: 1866.732 MHz
[    2.124940] clocksource: tsc: mask: 0xffffffffffffffff max_cycles: 0x35d0d1b66a8, max_idle_ns: 881590563120 ns
[    2.163352] ata2: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[    2.164066] ata2.00: ATA-7: SAMSUNG SSD UM410 Series 2.5" 16GB, VAM12D1Q, max UDMA/100
[    2.164070] ata2.00: 31277232 sectors, multi 16: LBA48 
[    2.164279] ata2.00: configured for UDMA/100
[    2.164609] scsi 1:0:0:0: Direct-Access     ATA      SAMSUNG SSD UM41 2D1Q PQ: 0 ANSI: 5
[    2.200117] sd 1:0:0:0: [sda] 31277232 512-byte logical blocks: (16.0 GB/14.9 GiB)
[    2.200275] sd 1:0:0:0: [sda] Write Protect is off
[    2.200280] sd 1:0:0:0: [sda] Mode Sense: 00 3a 00 00
[    2.200347] sd 1:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[    2.201376]  sda: sda1
[    2.202101] sd 1:0:0:0: [sda] Attached SCSI disk
[    2.203324] sd 1:0:0:0: Attached scsi generic sg0 type 0
[    2.437644] EXT4-fs (sda1): mounting ext2 file system using the ext4 subsystem
[    2.440761] EXT4-fs (sda1): mounted filesystem without journal. Opts: (null)
[    3.149066] clocksource: Switched to clocksource tsc
[    3.477197] random: fast init done
[    4.490728] udevd[340]: starting version 3.2.2
[    4.503124] random: udevd: uninitialized urandom read (16 bytes read)
[    4.503739] random: udevd: uninitialized urandom read (16 bytes read)
[    4.503765] random: udevd: uninitialized urandom read (16 bytes read)
[    4.523128] udevd[341]: starting eudev-3.2.2
[    4.820819] input: Power Button as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0C:00/input/input3
[    4.820828] ACPI: Power Button [PWRB]
[    4.820975] input: Sleep Button as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0E:00/input/input4
[    4.820980] ACPI: Sleep Button [SLPB]
[    4.821149] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input5
[    4.821153] ACPI: Power Button [PWRF]
[    5.002593] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
[    5.222086] ACPI Warning: SystemIO range 0x0000000000000428-0x000000000000042F conflicts with OpRegion 0x0000000000000400-0x000000000000047F (\PMIO) (20160831/utaddress-247)
[    5.222100] ACPI Warning: SystemIO range 0x0000000000000428-0x000000000000042F conflicts with OpRegion 0x0000000000000400-0x000000000000042F (\SWC1) (20160831/utaddress-247)
[    5.222110] ACPI: If an ACPI driver is available for this device, you should use it instead of the native driver
[    5.222113] ACPI Warning: SystemIO range 0x0000000000000530-0x000000000000053F conflicts with OpRegion 0x0000000000000500-0x000000000000053B (\GPIO) (20160831/utaddress-247)
[    5.222122] ACPI: If an ACPI driver is available for this device, you should use it instead of the native driver
[    5.222123] ACPI Warning: SystemIO range 0x0000000000000500-0x000000000000052F conflicts with OpRegion 0x0000000000000500-0x000000000000053B (\GPIO) (20160831/utaddress-247)
[    5.222131] ACPI: If an ACPI driver is available for this device, you should use it instead of the native driver
[    5.222133] lpc_ich: Resource conflict(s) found affecting gpio_ich
[    5.249801] input: PC Speaker as /devices/platform/pcspkr/input/input6
[    5.842602] iTCO_vendor_support: vendor-support=0
[    5.845490] iTCO_wdt: Intel TCO WatchDog Timer Driver v1.11
[    5.845568] iTCO_wdt: Found a NM10 TCO device (Version=2, TCOBASE=0x0460)
[    5.845841] iTCO_wdt: initialized. heartbeat=30 sec (nowayout=0)
[    5.864287] ath10k_pci 0000:03:00.0: pci irq msi oper_irq_mode 2 irq_mode 0 reset_mode 0
[    6.232276] ath10k_pci 0000:03:00.0: firmware: failed to load ath10k/pre-cal-pci-0000:03:00.0.bin (-2)
[    6.232801] ath10k_pci 0000:03:00.0: Direct firmware load for ath10k/pre-cal-pci-0000:03:00.0.bin failed with error -2
[    6.232859] ath10k_pci 0000:03:00.0: firmware: failed to load ath10k/cal-pci-0000:03:00.0.bin (-2)
[    6.233380] ath10k_pci 0000:03:00.0: Direct firmware load for ath10k/cal-pci-0000:03:00.0.bin failed with error -2
[    6.425445] ath10k_pci 0000:03:00.0: firmware: direct-loading firmware ath10k/QCA988X/hw2.0/firmware-5.bin
[    6.425466] ath10k_pci 0000:03:00.0: qca988x hw2.0 target 0x4100016c chip_id 0x043202ff sub 0000:0000
[    6.425471] ath10k_pci 0000:03:00.0: kconfig debug 0 debugfs 0 tracing 0 dfs 0 testmode 0
[    6.426107] ath10k_pci 0000:03:00.0: firmware ver 10.2.4-1.0-00041 api 5 features no-p2p,raw-mode,mfp crc32 f43fa422
[    6.460107] ath10k_pci 0000:03:00.0: firmware: failed to load ath10k/QCA988X/hw2.0/board-2.bin (-2)
[    6.460563] ath10k_pci 0000:03:00.0: Direct firmware load for ath10k/QCA988X/hw2.0/board-2.bin failed with error -2
[    6.463555] ath10k_pci 0000:03:00.0: firmware: direct-loading firmware ath10k/QCA988X/hw2.0/board.bin
[    6.463588] ath10k_pci 0000:03:00.0: board_file api 1 bmi_id N/A crc32 bebc7c08
[    6.729237] ip_tables: (C) 2000-2006 Netfilter Core Team
[    6.745452] nf_conntrack version 0.5.0 (16384 buckets, 65536 max)
[    6.753397] e100 0000:05:04.0 eth0: NIC Link is Up 100 Mbps Full Duplex
[    7.391211] bridge: filtering via arp/ip/ip6tables is no longer available by default. Update your scripts to load br_netfilter if you need this.
[    7.404448] br0: port 1(eth1) entered blocking state
[    7.404452] br0: port 1(eth1) entered disabled state
[    7.404586] device eth1 entered promiscuous mode
[    7.433422] e100 0000:05:05.0 eth1: NIC Link is Up 100 Mbps Full Duplex
[    7.438805] br0: port 1(eth1) entered blocking state
[    7.438811] br0: port 1(eth1) entered forwarding state
[    7.600905] ath10k_pci 0000:03:00.0: htt-ver 2.1 wmi-op 5 htt-op 2 cal otp max-sta 128 raw 0 hwcrypto 1
[    7.691941] ath: EEPROM regdomain: 0x0
[    7.691944] ath: EEPROM indicates default country code should be used
[    7.691945] ath: doing EEPROM country->regdmn map search
[    7.691948] ath: country maps to regdmn code: 0x3a
[    7.691950] ath: Country alpha2 being used: US
[    7.691951] ath: Regpair used: 0x3a
[    8.442648] EXT4-fs (sda1): re-mounted. Opts: errors=remount-ro,discard,commit=60
[    8.877862] w83627ehf: Found W83627UHG chip at 0x290
[    8.934181] e1000e: eth2 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: None
[    9.672652] urandom_read: 3 callbacks suppressed
[    9.672656] random: dd: uninitialized urandom read (512 bytes read)
[   12.118628] PPP generic driver version 2.4.2
[   12.418982] elogind[1992]: New seat seat0.
[   12.420849] elogind[1992]: Watching system buttons on /dev/input/event2 (Power Button)
[   12.421062] elogind[1992]: Watching system buttons on /dev/input/event0 (Power Button)
[   12.421311] elogind[1992]: Watching system buttons on /dev/input/event1 (Sleep Button)
[   12.467892] br0: port 2(wlan0) entered blocking state
[   12.467896] br0: port 2(wlan0) entered disabled state
[   12.468036] device wlan0 entered promiscuous mode
[   12.468078] br0: port 2(wlan0) entered blocking state
[   12.468081] br0: port 2(wlan0) entered forwarding state
[   12.469026] br0: port 2(wlan0) entered disabled state
[   12.471366] NET: Registered protocol family 24
[   12.482066] l2tp_core: L2TP core driver, V2.0
[   12.483661] l2tp_netlink: L2TP netlink interface
[   12.485172] l2tp_ppp: PPPoL2TP kernel driver, V2.0
[   12.491620] ath: EEPROM regdomain: 0x833a
[   12.491624] ath: EEPROM indicates we should expect a country code
[   12.491627] ath: doing EEPROM country->regdmn map search
[   12.491629] ath: country maps to regdmn code: 0x37
[   12.491631] ath: Country alpha2 being used: GB
[   12.491633] ath: Regpair used: 0x37
[   12.491635] ath: regdomain 0x833a dynamically updated by user
[   15.831897] br0: port 2(wlan0) entered blocking state
[   15.831902] br0: port 2(wlan0) entered forwarding state
[  105.004278] elogind[1992]: New session 1 of user deuser.
[  317.021824] random: crng init done

Это после reboot

[    0.000000] Linux version 4.9.189-ath-regd (root@devuan) (gcc version 6.3.0 20170516 (Debian 6.3.0-18+deb9u1) ) #1 SMP Wed Dec 4 19:06:16 UTC 2019
[    0.000000] Command line: BOOT_IMAGE=/boot/vmlinuz-4.9.189-ath-regd root=UUID=903ff076-53bc-4745-a66a-34faad0960cf ro quiet vga=0x031b quiet elevator=noop ipv6.disable=1 vga=0x031b
[    0.000000] Disabled fast string operations
[    0.000000] x86/fpu: Legacy x87 FPU detected.
[    0.000000] e820: BIOS-provided physical RAM map:
[    0.000000] BIOS-e820: [mem 0x0000000000000000-0x000000000008efff] usable
[    0.000000] BIOS-e820: [mem 0x000000000008f000-0x000000000008ffff] reserved
[    0.000000] BIOS-e820: [mem 0x0000000000090000-0x000000000009e7ff] usable
[    0.000000] BIOS-e820: [mem 0x000000000009e800-0x000000000009ffff] reserved
[    0.000000] BIOS-e820: [mem 0x00000000000e0000-0x00000000000fffff] reserved
[    0.000000] BIOS-e820: [mem 0x0000000000100000-0x00000000ceebcfff] usable
[    0.000000] BIOS-e820: [mem 0x00000000ceebd000-0x00000000ceebefff] reserved
[    0.000000] BIOS-e820: [mem 0x00000000ceebf000-0x00000000cef08fff] usable
[    0.000000] BIOS-e820: [mem 0x00000000cef09000-0x00000000cefbefff] ACPI NVS
[    0.000000] BIOS-e820: [mem 0x00000000cefbf000-0x00000000ceff0fff] usable
[    0.000000] BIOS-e820: [mem 0x00000000ceff1000-0x00000000ceffefff] ACPI data
[    0.000000] BIOS-e820: [mem 0x00000000cefff000-0x00000000ceffffff] usable
[    0.000000] BIOS-e820: [mem 0x00000000cf000000-0x00000000cfffffff] reserved
[    0.000000] BIOS-e820: [mem 0x00000000e0000000-0x00000000e3ffffff] reserved
[    0.000000] BIOS-e820: [mem 0x00000000ffe00000-0x00000000ffffffff] reserved
[    0.000000] BIOS-e820: [mem 0x0000000100000000-0x000000012fffffff] usable
[    0.000000] NX (Execute Disable) protection: active
[    0.000000] SMBIOS 2.7 present.
[    0.000000] DMI:  /D2500CC, BIOS CCCDT10N.86A.0040.2014.0520.1400 05/20/2014
[    0.000000] e820: update [mem 0x00000000-0x00000fff] usable ==> reserved
[    0.000000] e820: remove [mem 0x000a0000-0x000fffff] usable
[    0.000000] e820: last_pfn = 0x130000 max_arch_pfn = 0x400000000
[    0.000000] MTRR default type: uncachable
[    0.000000] MTRR fixed ranges enabled:
[    0.000000]   00000-9FFFF write-back
[    0.000000]   A0000-BFFFF uncachable
[    0.000000]   C0000-DFFFF write-protect
[    0.000000]   E0000-FFFFF uncachable
[    0.000000] MTRR variable ranges enabled:
[    0.000000]   0 base 000000000 mask F80000000 write-back
[    0.000000]   1 base 080000000 mask FC0000000 write-back
[    0.000000]   2 base 0C0000000 mask FF0000000 write-back
[    0.000000]   3 base 0CF000000 mask FFF000000 uncachable
[    0.000000]   4 base 100000000 mask FC0000000 write-back
[    0.000000]   5 base 0FFE00000 mask FFFE00000 write-protect
[    0.000000]   6 disabled
[    0.000000] x86/PAT: Configuration [0-7]: WB  WC  UC- UC  WB  WC  UC- WT  
[    0.000000] e820: last_pfn = 0xcf000 max_arch_pfn = 0x400000000
[    0.000000] found SMP MP-table at [mem 0x000fbe30-0x000fbe3f] mapped at [ffff90ce800fbe30]
[    0.000000] Base memory trampoline at [ffff90ce80098000] 98000 size 24576
[    0.000000] BRK [0x3c134000, 0x3c134fff] PGTABLE
[    0.000000] BRK [0x3c135000, 0x3c135fff] PGTABLE
[    0.000000] BRK [0x3c136000, 0x3c136fff] PGTABLE
[    0.000000] BRK [0x3c137000, 0x3c137fff] PGTABLE
[    0.000000] BRK [0x3c138000, 0x3c138fff] PGTABLE
[    0.000000] RAMDISK: [mem 0x35675000-0x36b31fff]
[    0.000000] ACPI: Early table checksum verification disabled
[    0.000000] ACPI: RSDP 0x00000000000F2390 000024 (v02 INTEL )
[    0.000000] ACPI: XSDT 0x00000000CEFFE120 00004C (v01 INTEL  D2500CC  00000028      01000013)
[    0.000000] ACPI: FACP 0x00000000CEFF5000 0000F4 (v03 INTEL  D2500CC  00000028 MSFT 0100000D)
[    0.000000] ACPI BIOS Warning (bug): 32/64X length mismatch in FADT/Pm1aEventBlock: 32/16 (20160831/tbfadt-603)
[    0.000000] ACPI BIOS Warning (bug): 32/64X length mismatch in FADT/PmTimerBlock: 32/24 (20160831/tbfadt-603)
[    0.000000] ACPI BIOS Warning (bug): Invalid length for FADT/Pm1aEventBlock: 16, using default 32 (20160831/tbfadt-708)
[    0.000000] ACPI BIOS Warning (bug): Invalid length for FADT/PmTimerBlock: 24, using default 32 (20160831/tbfadt-708)
[    0.000000] ACPI: DSDT 0x00000000CEFF7000 0067A0 (v02 INTEL  D2500CC  00000028 MSFT 0100000D)
[    0.000000] ACPI: FACS 0x00000000CEF95000 000040
[    0.000000] ACPI: FACS 0x00000000CEF95000 000040
[    0.000000] ACPI: SSDT 0x00000000CEFF6000 00043E (v01 INTEL  D2500CC  00000028 MSFT 0100000D)
[    0.000000] ACPI: APIC 0x00000000CEFF4000 000084 (v02 INTEL  D2500CC  00000028 MSFT 0100000D)
[    0.000000] ACPI: MCFG 0x00000000CEFF3000 00003C (v01 INTEL  D2500CC  00000028 MSFT 0100000D)
[    0.000000] ACPI: HPET 0x00000000CEFF2000 000038 (v01 INTEL  D2500CC  00000028 MSFT 0100000D)
[    0.000000] ACPI: Local APIC address 0xfee00000
[    0.000000] No NUMA configuration found
[    0.000000] Faking a node at [mem 0x0000000000000000-0x000000012fffffff]
[    0.000000] NODE_DATA(0) allocated [mem 0x12fff7000-0x12fffbfff]
[    0.000000] Zone ranges:
[    0.000000]   DMA      [mem 0x0000000000001000-0x0000000000ffffff]
[    0.000000]   DMA32    [mem 0x0000000001000000-0x00000000ffffffff]
[    0.000000]   Normal   [mem 0x0000000100000000-0x000000012fffffff]
[    0.000000]   Device   empty
[    0.000000] Movable zone start for each node
[    0.000000] Early memory node ranges
[    0.000000]   node   0: [mem 0x0000000000001000-0x000000000008efff]
[    0.000000]   node   0: [mem 0x0000000000090000-0x000000000009dfff]
[    0.000000]   node   0: [mem 0x0000000000100000-0x00000000ceebcfff]
[    0.000000]   node   0: [mem 0x00000000ceebf000-0x00000000cef08fff]
[    0.000000]   node   0: [mem 0x00000000cefbf000-0x00000000ceff0fff]
[    0.000000]   node   0: [mem 0x00000000cefff000-0x00000000ceffffff]
[    0.000000]   node   0: [mem 0x0000000100000000-0x000000012fffffff]
[    0.000000] Initmem setup node 0 [mem 0x0000000000001000-0x000000012fffffff]
[    0.000000] On node 0 totalpages: 1044182
[    0.000000]   DMA zone: 64 pages used for memmap
[    0.000000]   DMA zone: 21 pages reserved
[    0.000000]   DMA zone: 3996 pages, LIFO batch:0
[    0.000000]   DMA32 zone: 13181 pages used for memmap
[    0.000000]   DMA32 zone: 843578 pages, LIFO batch:31
[    0.000000]   Normal zone: 3072 pages used for memmap
[    0.000000]   Normal zone: 196608 pages, LIFO batch:31
[    0.000000] ACPI: PM-Timer IO Port: 0x408
[    0.000000] ACPI: Local APIC address 0xfee00000
[    0.000000] ACPI: LAPIC_NMI (acpi_id[0x01] high level lint[0x1])
[    0.000000] ACPI: LAPIC_NMI (acpi_id[0x02] high level lint[0x1])
[    0.000000] ACPI: LAPIC_NMI (acpi_id[0x03] high level lint[0x1])
[    0.000000] ACPI: LAPIC_NMI (acpi_id[0x04] high level lint[0x1])
[    0.000000] IOAPIC[0]: apic_id 8, version 32, address 0xfec00000, GSI 0-23
[    0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
[    0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
[    0.000000] ACPI: IRQ0 used by override.
[    0.000000] ACPI: IRQ9 used by override.
[    0.000000] Using ACPI (MADT) for SMP configuration information
[    0.000000] ACPI: HPET id: 0x8086a201 base: 0xfed00000
[    0.000000] smpboot: Allowing 4 CPUs, 2 hotplug CPUs
[    0.000000] PM: Registered nosave memory: [mem 0x00000000-0x00000fff]
[    0.000000] PM: Registered nosave memory: [mem 0x0008f000-0x0008ffff]
[    0.000000] PM: Registered nosave memory: [mem 0x0009e000-0x0009efff]
[    0.000000] PM: Registered nosave memory: [mem 0x0009f000-0x0009ffff]
[    0.000000] PM: Registered nosave memory: [mem 0x000a0000-0x000dffff]
[    0.000000] PM: Registered nosave memory: [mem 0x000e0000-0x000fffff]
[    0.000000] PM: Registered nosave memory: [mem 0xceebd000-0xceebefff]
[    0.000000] PM: Registered nosave memory: [mem 0xcef09000-0xcefbefff]
[    0.000000] PM: Registered nosave memory: [mem 0xceff1000-0xceffefff]
[    0.000000] PM: Registered nosave memory: [mem 0xcf000000-0xcfffffff]
[    0.000000] PM: Registered nosave memory: [mem 0xd0000000-0xdfffffff]
[    0.000000] PM: Registered nosave memory: [mem 0xe0000000-0xe3ffffff]
[    0.000000] PM: Registered nosave memory: [mem 0xe4000000-0xffdfffff]
[    0.000000] PM: Registered nosave memory: [mem 0xffe00000-0xffffffff]
[    0.000000] e820: [mem 0xe4000000-0xffdfffff] available for PCI devices
[    0.000000] Booting paravirtualized kernel on bare hardware
[    0.000000] clocksource: refined-jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645519600211568 ns
[    0.000000] setup_percpu: NR_CPUS:512 nr_cpumask_bits:512 nr_cpu_ids:4 nr_node_ids:1
[    0.000000] percpu: Embedded 35 pages/cpu s105304 r8192 d29864 u524288
[    0.000000] pcpu-alloc: s105304 r8192 d29864 u524288 alloc=1*2097152
[    0.000000] pcpu-alloc: [0] 0 1 2 3 
[    0.000000] Built 1 zonelists in Node order, mobility grouping on.  Total pages: 1027844
[    0.000000] Policy zone: Normal
[    0.000000] Kernel command line: BOOT_IMAGE=/boot/vmlinuz-4.9.189-ath-regd root=UUID=903ff076-53bc-4745-a66a-34faad0960cf ro quiet vga=0x031b quiet elevator=noop ipv6.disable=1 vga=0x031b
[    0.000000] PID hash table entries: 4096 (order: 3, 32768 bytes)
[    0.000000] Calgary: detecting Calgary via BIOS EBDA area
[    0.000000] Calgary: Unable to locate Rio Grande table in EBDA - bailing!
[    0.000000] Memory: 4007644K/4176728K available (6284K kernel code, 1162K rwdata, 2848K rodata, 1424K init, 656K bss, 169084K reserved, 0K cma-reserved)
[    0.000000] Kernel/User page tables isolation: enabled
[    0.000000] Hierarchical RCU implementation.
[    0.000000] 	Build-time adjustment of leaf fanout to 64.
[    0.000000] 	RCU restricting CPUs from NR_CPUS=512 to nr_cpu_ids=4.
[    0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=64, nr_cpu_ids=4
[    0.000000] NR_IRQS:33024 nr_irqs:456 16
[    0.000000] Console: colour dummy device 80x25
[    0.000000] console [tty0] enabled
[    0.000000] clocksource: hpet: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 133484882848 ns
[    0.000000] hpet clockevent registered
[    0.000000] tsc: Fast TSC calibration using PIT
[    0.000000] tsc: Detected 1866.616 MHz processor
[    0.000052] Calibrating delay loop (skipped), value calculated using timer frequency.. 3733.23 BogoMIPS (lpj=7466464)
[    0.000058] pid_max: default: 32768 minimum: 301
[    0.000117] ACPI: Core revision 20160831
[    0.014334] ACPI: 2 ACPI AML tables successfully acquired and loaded
[    0.014497] Security Framework initialized
[    0.014500] Yama: disabled by default; enable with sysctl kernel.yama.*
[    0.014513] AppArmor: AppArmor disabled by boot time parameter
[    0.015214] Dentry cache hash table entries: 524288 (order: 10, 4194304 bytes)
[    0.018479] Inode-cache hash table entries: 262144 (order: 9, 2097152 bytes)
[    0.020035] Mount-cache hash table entries: 8192 (order: 4, 65536 bytes)
[    0.020056] Mountpoint-cache hash table entries: 8192 (order: 4, 65536 bytes)
[    0.020797] Disabled fast string operations
[    0.020809] mce: CPU supports 5 MCE banks
[    0.020820] CPU0: Thermal monitoring enabled (TM1)
[    0.020827] process: using mwait in idle threads
[    0.020834] Last level iTLB entries: 4KB 32, 2MB 0, 4MB 0
[    0.020837] Last level dTLB entries: 4KB 64, 2MB 0, 4MB 8, 1GB 0
[    0.021339] Freeing SMP alternatives memory: 24K
[    0.024404] ftrace: allocating 25339 entries in 99 pages
[    0.046946] smpboot: Max logical packages: 2
[    0.047434] ..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1
[    0.194864] smpboot: CPU0: Intel(R) Atom(TM) CPU D2500   @ 1.86GHz (family: 0x6, model: 0x36, stepping: 0x1)
[    0.194874] Performance Events: PEBS fmt0+, Atom events, 8-deep LBR, Intel PMU driver.
[    0.194895] ... version:                3
[    0.194896] ... bit width:              40
[    0.194897] ... generic registers:      2
[    0.194899] ... value mask:             000000ffffffffff
[    0.194900] ... max period:             000000007fffffff
[    0.194901] ... fixed-purpose events:   3
[    0.194903] ... event mask:             0000000700000003
[    0.196437] NMI watchdog: enabled on all CPUs, permanently consumes one hw-PMU counter.
[    0.196986] x86: Booting SMP configuration:
[    0.196989] .... node  #0, CPUs:      #1
[    0.197068] Disabled fast string operations
[    0.199237] x86: Booted up 1 node, 2 CPUs
[    0.199242] smpboot: Total of 2 processors activated (7466.46 BogoMIPS)
[    0.200520] devtmpfs: initialized
[    0.200726] x86/mm: Memory block size: 128MB
[    0.208908] PM: Registering ACPI NVS region [mem 0xcef09000-0xcefbefff] (745472 bytes)
[    0.209108] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns
[    0.209133] futex hash table entries: 1024 (order: 4, 65536 bytes)
[    0.209246] pinctrl core: initialized pinctrl subsystem
[    0.209561] NET: Registered protocol family 16
[    0.218878] cpuidle: using governor ladder
[    0.230877] cpuidle: using governor menu
[    0.230978] ACPI FADT declares the system doesn't support PCIe ASPM, so disable it
[    0.230981] ACPI: bus type PCI registered
[    0.230984] acpiphp: ACPI Hot Plug PCI Controller Driver version: 0.5
[    0.231187] PCI: MMCONFIG for domain 0000 [bus 00-3f] at [mem 0xe0000000-0xe3ffffff] (base 0xe0000000)
[    0.231192] PCI: MMCONFIG at [mem 0xe0000000-0xe3ffffff] reserved in E820
[    0.231207] PCI: Using configuration type 1 for base access
[    0.243329] HugeTLB registered 2 MB page size, pre-allocated 0 pages
[    0.244099] ACPI: Added _OSI(Module Device)
[    0.244102] ACPI: Added _OSI(Processor Device)
[    0.244104] ACPI: Added _OSI(3.0 _SCP Extensions)
[    0.244106] ACPI: Added _OSI(Processor Aggregator Device)
[    0.244461] ACPI: Executed 1 blocks of module-level executable AML code
[    0.251158] ACPI: [Firmware Bug]: BIOS _OSI(Linux) query ignored
[    0.252450] ACPI: Interpreter enabled
[    0.252498] ACPI: (supports S0 S3 S4 S5)
[    0.252501] ACPI: Using IOAPIC for interrupt routing
[    0.252589] PCI: Using host bridge windows from ACPI; if necessary, use "pci=nocrs" and report a bug
[    0.271578] ACPI: PCI Root Bridge [PCI0] (domain 0000 [bus 00-ff])
[    0.271591] acpi PNP0A08:00: _OSC: OS supports [ExtendedConfig ASPM ClockPM Segments MSI]
[    0.271713] acpi PNP0A08:00: _OSC failed (AE_ERROR); disabling ASPM
[    0.271740] acpi PNP0A08:00: [Firmware Info]: MMCONFIG for domain 0000 [bus 00-3f] only partially covers this bridge
[    0.272565] PCI host bridge to bus 0000:00
[    0.272571] pci_bus 0000:00: root bus resource [io  0x0000-0x0cf7 window]
[    0.272575] pci_bus 0000:00: root bus resource [io  0x0d00-0xffff window]
[    0.272579] pci_bus 0000:00: root bus resource [mem 0x000a0000-0x000bffff window]
[    0.272583] pci_bus 0000:00: root bus resource [mem 0x000c0000-0x000dffff window]
[    0.272586] pci_bus 0000:00: root bus resource [mem 0x000e0000-0x000effff window]
[    0.272590] pci_bus 0000:00: root bus resource [mem 0x000f0000-0x000fffff window]
[    0.272594] pci_bus 0000:00: root bus resource [mem 0xcf800000-0xcfffffff window]
[    0.272597] pci_bus 0000:00: root bus resource [mem 0xd0000000-0xfebfffff window]
[    0.272601] pci_bus 0000:00: root bus resource [mem 0xfed40000-0xfed44fff window]
[    0.272605] pci_bus 0000:00: root bus resource [bus 00-ff]
[    0.272621] pci 0000:00:00.0: [8086:0bf5] type 00 class 0x060000
[    0.272886] pci 0000:00:02.0: [8086:0be1] type 00 class 0x030000
[    0.272901] pci 0000:00:02.0: reg 0x10: [mem 0xd0500000-0xd05fffff]
[    0.272909] pci 0000:00:02.0: reg 0x14: [io  0x40d0-0x40d7]
[    0.273197] pci 0000:00:1c.0: [8086:27d0] type 01 class 0x060400
[    0.273310] pci 0000:00:1c.0: PME# supported from D0 D3hot D3cold
[    0.273438] pci 0000:00:1c.0: System wakeup disabled by ACPI
[    0.273558] pci 0000:00:1c.1: [8086:27d2] type 01 class 0x060400
[    0.273668] pci 0000:00:1c.1: PME# supported from D0 D3hot D3cold
[    0.273793] pci 0000:00:1c.1: System wakeup disabled by ACPI
[    0.273912] pci 0000:00:1d.0: [8086:27c8] type 00 class 0x0c0300
[    0.273968] pci 0000:00:1d.0: reg 0x20: [io  0x40a0-0x40bf]
[    0.274157] pci 0000:00:1d.0: System wakeup disabled by ACPI
[    0.274270] pci 0000:00:1d.1: [8086:27c9] type 00 class 0x0c0300
[    0.274326] pci 0000:00:1d.1: reg 0x20: [io  0x4080-0x409f]
[    0.274512] pci 0000:00:1d.1: System wakeup disabled by ACPI
[    0.274628] pci 0000:00:1d.2: [8086:27ca] type 00 class 0x0c0300
[    0.274684] pci 0000:00:1d.2: reg 0x20: [io  0x4060-0x407f]
[    0.274888] pci 0000:00:1d.2: System wakeup disabled by ACPI
[    0.275003] pci 0000:00:1d.3: [8086:27cb] type 00 class 0x0c0300
[    0.275058] pci 0000:00:1d.3: reg 0x20: [io  0x4040-0x405f]
[    0.275247] pci 0000:00:1d.3: System wakeup disabled by ACPI
[    0.275369] pci 0000:00:1d.7: [8086:27cc] type 00 class 0x0c0320
[    0.275394] pci 0000:00:1d.7: reg 0x10: [mem 0xd0600400-0xd06007ff]
[    0.275507] pci 0000:00:1d.7: PME# supported from D0 D3hot D3cold
[    0.275664] pci 0000:00:1d.7: System wakeup disabled by ACPI
[    0.275782] pci 0000:00:1e.0: [8086:2448] type 01 class 0x060401
[    0.276053] pci 0000:00:1f.0: [8086:27bc] type 00 class 0x060100
[    0.276159] pci 0000:00:1f.0: [Firmware Bug]: TigerPoint LPC.BM_STS cleared
[    0.276394] pci 0000:00:1f.2: [8086:27c1] type 00 class 0x010601
[    0.276416] pci 0000:00:1f.2: reg 0x10: [io  0x40c8-0x40cf]
[    0.276428] pci 0000:00:1f.2: reg 0x14: [io  0x40dc-0x40df]
[    0.276440] pci 0000:00:1f.2: reg 0x18: [io  0x40c0-0x40c7]
[    0.276451] pci 0000:00:1f.2: reg 0x1c: [io  0x40d8-0x40db]
[    0.276463] pci 0000:00:1f.2: reg 0x20: [io  0x4020-0x402f]
[    0.276475] pci 0000:00:1f.2: reg 0x24: [mem 0xd0600000-0xd06003ff]
[    0.276533] pci 0000:00:1f.2: PME# supported from D3hot
[    0.276751] pci 0000:00:1f.3: [8086:27da] type 00 class 0x0c0500
[    0.276816] pci 0000:00:1f.3: reg 0x20: [io  0x4000-0x401f]
[    0.277217] pci 0000:02:00.0: [8086:10d3] type 00 class 0x020000
[    0.277255] pci 0000:02:00.0: reg 0x10: [mem 0xd0420000-0xd043ffff]
[    0.277276] pci 0000:02:00.0: reg 0x14: [mem 0xd0400000-0xd041ffff]
[    0.277297] pci 0000:02:00.0: reg 0x18: [io  0x3000-0x301f]
[    0.277318] pci 0000:02:00.0: reg 0x1c: [mem 0xd0440000-0xd0443fff]
[    0.277503] pci 0000:02:00.0: PME# supported from D0 D3hot D3cold
[    0.277591] pci 0000:02:00.0: System wakeup disabled by ACPI
[    0.286903] pci 0000:00:1c.0: PCI bridge to [bus 02]
[    0.286910] pci 0000:00:1c.0:   bridge window [io  0x3000-0x3fff]
[    0.286916] pci 0000:00:1c.0:   bridge window [mem 0xd0400000-0xd04fffff]
[    0.287080] pci 0000:01:00.0: [8086:10d3] type 00 class 0x020000
[    0.287117] pci 0000:01:00.0: reg 0x10: [mem 0xd0320000-0xd033ffff]
[    0.287139] pci 0000:01:00.0: reg 0x14: [mem 0xd0300000-0xd031ffff]
[    0.287160] pci 0000:01:00.0: reg 0x18: [io  0x2000-0x201f]
[    0.287181] pci 0000:01:00.0: reg 0x1c: [mem 0xd0340000-0xd0343fff]
[    0.287368] pci 0000:01:00.0: PME# supported from D0 D3hot D3cold
[    0.287459] pci 0000:01:00.0: System wakeup disabled by ACPI
[    0.298899] pci 0000:00:1c.1: PCI bridge to [bus 01]
[    0.298905] pci 0000:00:1c.1:   bridge window [io  0x2000-0x2fff]
[    0.298911] pci 0000:00:1c.1:   bridge window [mem 0xd0300000-0xd03fffff]
[    0.299040] pci 0000:03:00.0: [1011:0024] type 01 class 0x060400
[    0.299179] pci 0000:03:00.0: System wakeup disabled by ACPI
[    0.299334] pci 0000:00:1e.0: PCI bridge to [bus 03-04] (subtractive decode)
[    0.299341] pci 0000:00:1e.0:   bridge window [io  0x1000-0x1fff]
[    0.299347] pci 0000:00:1e.0:   bridge window [mem 0xd0100000-0xd02fffff]
[    0.299355] pci 0000:00:1e.0:   bridge window [mem 0xd0000000-0xd00fffff 64bit pref]
[    0.299360] pci 0000:00:1e.0:   bridge window [io  0x0000-0x0cf7 window] (subtractive decode)
[    0.299364] pci 0000:00:1e.0:   bridge window [io  0x0d00-0xffff window] (subtractive decode)
[    0.299368] pci 0000:00:1e.0:   bridge window [mem 0x000a0000-0x000bffff window] (subtractive decode)
[    0.299372] pci 0000:00:1e.0:   bridge window [mem 0x000c0000-0x000dffff window] (subtractive decode)
[    0.299375] pci 0000:00:1e.0:   bridge window [mem 0x000e0000-0x000effff window] (subtractive decode)
[    0.299379] pci 0000:00:1e.0:   bridge window [mem 0x000f0000-0x000fffff window] (subtractive decode)
[    0.299383] pci 0000:00:1e.0:   bridge window [mem 0xcf800000-0xcfffffff window] (subtractive decode)
[    0.299386] pci 0000:00:1e.0:   bridge window [mem 0xd0000000-0xfebfffff window] (subtractive decode)
[    0.299390] pci 0000:00:1e.0:   bridge window [mem 0xfed40000-0xfed44fff window] (subtractive decode)
[    0.299492] pci 0000:04:04.0: [8086:1229] type 00 class 0x020000
[    0.299520] pci 0000:04:04.0: reg 0x10: [mem 0xd0001000-0xd0001fff pref]
[    0.299536] pci 0000:04:04.0: reg 0x14: [io  0x1020-0x103f]
[    0.299551] pci 0000:04:04.0: reg 0x18: [mem 0xd0200000-0xd02fffff]
[    0.299603] pci 0000:04:04.0: reg 0x30: [mem 0xfff00000-0xffffffff pref]
[    0.299664] pci 0000:04:04.0: supports D1 D2
[    0.299667] pci 0000:04:04.0: PME# supported from D0 D1 D2 D3hot
[    0.299805] pci 0000:04:05.0: [8086:1229] type 00 class 0x020000
[    0.299832] pci 0000:04:05.0: reg 0x10: [mem 0xd0000000-0xd0000fff pref]
[    0.299848] pci 0000:04:05.0: reg 0x14: [io  0x1000-0x101f]
[    0.299864] pci 0000:04:05.0: reg 0x18: [mem 0xd0100000-0xd01fffff]
[    0.299916] pci 0000:04:05.0: reg 0x30: [mem 0xfff00000-0xffffffff pref]
[    0.299976] pci 0000:04:05.0: supports D1 D2
[    0.299979] pci 0000:04:05.0: PME# supported from D0 D1 D2 D3hot
[    0.300145] pci 0000:03:00.0: PCI bridge to [bus 04]
[    0.300155] pci 0000:03:00.0:   bridge window [io  0x1000-0x1fff]
[    0.300161] pci 0000:03:00.0:   bridge window [mem 0xd0100000-0xd02fffff]
[    0.300170] pci 0000:03:00.0:   bridge window [mem 0xd0000000-0xd00fffff 64bit pref]
[    0.301757] ACPI: PCI Interrupt Link [LNKA] (IRQs 1 3 4 5 6 7 10 12 14 15) *11
[    0.301937] ACPI: PCI Interrupt Link [LNKB] (IRQs 1 3 4 5 6 7 11 12 14 15) *9
[    0.302113] ACPI: PCI Interrupt Link [LNKC] (IRQs 1 3 4 5 6 7 10 12 14 15) *9
[    0.302289] ACPI: PCI Interrupt Link [LNKD] (IRQs 1 3 4 5 6 7 *11 12 14 15)
[    0.302464] ACPI: PCI Interrupt Link [LNKE] (IRQs 1 3 4 5 6 7 *10 12 14 15)
[    0.302645] ACPI: PCI Interrupt Link [LNKF] (IRQs 1 3 4 5 6 7 *11 12 14 15)
[    0.302819] ACPI: PCI Interrupt Link [LNKG] (IRQs 1 3 4 5 6 7 10 12 14 15) *0, disabled.
[    0.303024] ACPI: PCI Interrupt Link [LNKH] (IRQs 1 3 4 5 6 7 11 12 14 15) *10
[    0.303412] ACPI: Enabled 6 GPEs in block 00 to 1F
[    0.303721] vgaarb: setting as boot device: PCI:0000:00:02.0
[    0.303725] vgaarb: device added: PCI:0000:00:02.0,decodes=io+mem,owns=io+mem,locks=none
[    0.303734] vgaarb: loaded
[    0.303736] vgaarb: bridge control possible 0000:00:02.0
[    0.303992] PCI: Using ACPI for IRQ routing
[    0.305940] PCI: pci_cache_line_size set to 64 bytes
[    0.306025] e820: reserve RAM buffer [mem 0x0008f000-0x0008ffff]
[    0.306029] e820: reserve RAM buffer [mem 0x0009e800-0x0009ffff]
[    0.306032] e820: reserve RAM buffer [mem 0xceebd000-0xcfffffff]
[    0.306035] e820: reserve RAM buffer [mem 0xcef09000-0xcfffffff]
[    0.306037] e820: reserve RAM buffer [mem 0xceff1000-0xcfffffff]
[    0.306040] e820: reserve RAM buffer [mem 0xcf000000-0xcfffffff]
[    0.306510] hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0
[    0.306518] hpet0: 3 comparators, 64-bit 14.318180 MHz counter
[    0.308586] clocksource: Switched to clocksource hpet
[    0.331192] VFS: Disk quotas dquot_6.6.0
[    0.331256] VFS: Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
[    0.331507] pnp: PnP ACPI init
[    0.331943] system 00:00: [mem 0xfed00000-0xfed003ff] has been reserved
[    0.331953] system 00:00: Plug and Play ACPI device, IDs PNP0103 PNP0c01 (active)
[    0.332114] system 00:01: [io  0x0680-0x069f] has been reserved
[    0.332120] system 00:01: [io  0xffff] has been reserved
[    0.332124] system 00:01: [io  0xffff] has been reserved
[    0.332128] system 00:01: [io  0xffff] has been reserved
[    0.332133] system 00:01: [io  0x0400-0x047f] has been reserved
[    0.332138] system 00:01: [io  0x0500-0x057f] has been reserved
[    0.332142] system 00:01: [io  0x0600-0x061f] has been reserved
[    0.332149] system 00:01: Plug and Play ACPI device, IDs PNP0c02 (active)
[    0.332317] system 00:02: [io  0x06a0-0x06af] has been reserved
[    0.332322] system 00:02: [io  0x06b0-0x06ff] has been reserved
[    0.332328] system 00:02: Plug and Play ACPI device, IDs PNP0c02 (active)
[    0.332416] pnp 00:03: Plug and Play ACPI device, IDs PNP0b00 (active)
[    0.333329] ACPI: IRQ 3 override to edge, high
[    0.333491] pnp 00:04: Plug and Play ACPI device, IDs PNP0501 (active)
[    0.333854] ACPI: IRQ 4 override to edge, high
[    0.334007] pnp 00:05: Plug and Play ACPI device, IDs PNP0501 (active)
[    0.334432] system 00:06: [mem 0xfed1c000-0xfed1ffff] has been reserved
[    0.334438] system 00:06: [mem 0x00000000-0x00003fff] could not be reserved
[    0.334443] system 00:06: [mem 0x00000000-0x00000fff] could not be reserved
[    0.334447] system 00:06: [mem 0x00000000-0x00000fff] could not be reserved
[    0.334451] system 00:06: [mem 0xfed45000-0xfed8ffff] has been reserved
[    0.334458] system 00:06: Plug and Play ACPI device, IDs PNP0c02 (active)
[    0.334825] pnp: PnP ACPI: found 7 devices
[    0.345348] clocksource: acpi_pm: mask: 0xffffff max_cycles: 0xffffff, max_idle_ns: 2085701024 ns
[    0.345365] pci 0000:04:04.0: can't claim BAR 6 [mem 0xfff00000-0xffffffff pref]: no compatible bridge window
[    0.345370] pci 0000:04:05.0: can't claim BAR 6 [mem 0xfff00000-0xffffffff pref]: no compatible bridge window
[    0.345400] pci 0000:00:1c.0: bridge window [mem 0x00100000-0x000fffff 64bit pref] to [bus 02] add_size 200000 add_align 100000
[    0.345415] pci 0000:00:1c.1: bridge window [mem 0x00100000-0x000fffff 64bit pref] to [bus 01] add_size 200000 add_align 100000
[    0.345452] pci 0000:00:1c.0: res[15]=[mem 0x00100000-0x000fffff 64bit pref] res_to_dev_res add_size 200000 min_align 100000
[    0.345456] pci 0000:00:1c.0: res[15]=[mem 0x00100000-0x002fffff 64bit pref] res_to_dev_res add_size 200000 min_align 100000
[    0.345461] pci 0000:00:1c.1: res[15]=[mem 0x00100000-0x000fffff 64bit pref] res_to_dev_res add_size 200000 min_align 100000
[    0.345465] pci 0000:00:1c.1: res[15]=[mem 0x00100000-0x002fffff 64bit pref] res_to_dev_res add_size 200000 min_align 100000
[    0.345482] pci 0000:00:1c.0: BAR 15: assigned [mem 0xd0700000-0xd08fffff 64bit pref]
[    0.345495] pci 0000:00:1c.1: BAR 15: assigned [mem 0xd0900000-0xd0afffff 64bit pref]
[    0.345501] pci 0000:00:1c.0: PCI bridge to [bus 02]
[    0.345506] pci 0000:00:1c.0:   bridge window [io  0x3000-0x3fff]
[    0.345513] pci 0000:00:1c.0:   bridge window [mem 0xd0400000-0xd04fffff]
[    0.345520] pci 0000:00:1c.0:   bridge window [mem 0xd0700000-0xd08fffff 64bit pref]
[    0.345528] pci 0000:00:1c.1: PCI bridge to [bus 01]
[    0.345533] pci 0000:00:1c.1:   bridge window [io  0x2000-0x2fff]
[    0.345540] pci 0000:00:1c.1:   bridge window [mem 0xd0300000-0xd03fffff]
[    0.345546] pci 0000:00:1c.1:   bridge window [mem 0xd0900000-0xd0afffff 64bit pref]
[    0.345561] pci 0000:04:04.0: BAR 6: no space for [mem size 0x00100000 pref]
[    0.345565] pci 0000:04:04.0: BAR 6: failed to assign [mem size 0x00100000 pref]
[    0.345570] pci 0000:04:05.0: BAR 6: no space for [mem size 0x00100000 pref]
[    0.345573] pci 0000:04:05.0: BAR 6: failed to assign [mem size 0x00100000 pref]
[    0.345577] pci 0000:03:00.0: PCI bridge to [bus 04]
[    0.345582] pci 0000:03:00.0:   bridge window [io  0x1000-0x1fff]
[    0.345590] pci 0000:03:00.0:   bridge window [mem 0xd0100000-0xd02fffff]
[    0.345596] pci 0000:03:00.0:   bridge window [mem 0xd0000000-0xd00fffff 64bit pref]
[    0.345605] pci 0000:00:1e.0: PCI bridge to [bus 03-04]
[    0.345610] pci 0000:00:1e.0:   bridge window [io  0x1000-0x1fff]
[    0.345617] pci 0000:00:1e.0:   bridge window [mem 0xd0100000-0xd02fffff]
[    0.345622] pci 0000:00:1e.0:   bridge window [mem 0xd0000000-0xd00fffff 64bit pref]
[    0.345632] pci_bus 0000:00: resource 4 [io  0x0000-0x0cf7 window]
[    0.345636] pci_bus 0000:00: resource 5 [io  0x0d00-0xffff window]
[    0.345640] pci_bus 0000:00: resource 6 [mem 0x000a0000-0x000bffff window]
[    0.345643] pci_bus 0000:00: resource 7 [mem 0x000c0000-0x000dffff window]
[    0.345646] pci_bus 0000:00: resource 8 [mem 0x000e0000-0x000effff window]
[    0.345650] pci_bus 0000:00: resource 9 [mem 0x000f0000-0x000fffff window]
[    0.345653] pci_bus 0000:00: resource 10 [mem 0xcf800000-0xcfffffff window]
[    0.345657] pci_bus 0000:00: resource 11 [mem 0xd0000000-0xfebfffff window]
[    0.345660] pci_bus 0000:00: resource 12 [mem 0xfed40000-0xfed44fff window]
[    0.345664] pci_bus 0000:02: resource 0 [io  0x3000-0x3fff]
[    0.345667] pci_bus 0000:02: resource 1 [mem 0xd0400000-0xd04fffff]
[    0.345671] pci_bus 0000:02: resource 2 [mem 0xd0700000-0xd08fffff 64bit pref]
[    0.345675] pci_bus 0000:01: resource 0 [io  0x2000-0x2fff]
[    0.345678] pci_bus 0000:01: resource 1 [mem 0xd0300000-0xd03fffff]
[    0.345682] pci_bus 0000:01: resource 2 [mem 0xd0900000-0xd0afffff 64bit pref]
[    0.345685] pci_bus 0000:03: resource 0 [io  0x1000-0x1fff]
[    0.345689] pci_bus 0000:03: resource 1 [mem 0xd0100000-0xd02fffff]
[    0.345692] pci_bus 0000:03: resource 2 [mem 0xd0000000-0xd00fffff 64bit pref]
[    0.345695] pci_bus 0000:03: resource 4 [io  0x0000-0x0cf7 window]
[    0.345699] pci_bus 0000:03: resource 5 [io  0x0d00-0xffff window]
[    0.345702] pci_bus 0000:03: resource 6 [mem 0x000a0000-0x000bffff window]
[    0.345706] pci_bus 0000:03: resource 7 [mem 0x000c0000-0x000dffff window]
[    0.345709] pci_bus 0000:03: resource 8 [mem 0x000e0000-0x000effff window]
[    0.345712] pci_bus 0000:03: resource 9 [mem 0x000f0000-0x000fffff window]
[    0.345716] pci_bus 0000:03: resource 10 [mem 0xcf800000-0xcfffffff window]
[    0.345719] pci_bus 0000:03: resource 11 [mem 0xd0000000-0xfebfffff window]
[    0.345723] pci_bus 0000:03: resource 12 [mem 0xfed40000-0xfed44fff window]
[    0.345726] pci_bus 0000:04: resource 0 [io  0x1000-0x1fff]
[    0.345730] pci_bus 0000:04: resource 1 [mem 0xd0100000-0xd02fffff]
[    0.345733] pci_bus 0000:04: resource 2 [mem 0xd0000000-0xd00fffff 64bit pref]
[    0.346012] NET: Registered protocol family 2
[    0.346479] TCP established hash table entries: 32768 (order: 6, 262144 bytes)
[    0.346718] TCP bind hash table entries: 32768 (order: 7, 524288 bytes)
[    0.347021] TCP: Hash tables configured (established 32768 bind 32768)
[    0.347167] UDP hash table entries: 2048 (order: 4, 65536 bytes)
[    0.347229] UDP-Lite hash table entries: 2048 (order: 4, 65536 bytes)
[    0.347451] NET: Registered protocol family 1
[    0.347492] pci 0000:00:02.0: Video device with shadowed ROM at [mem 0x000c0000-0x000dffff]
[    0.348837] pci 0000:04:04.0: Firmware left e100 interrupts enabled; disabling
[    0.348860] pci 0000:04:05.0: Firmware left e100 interrupts enabled; disabling
[    0.348869] PCI: CLS 64 bytes, default 64
[    0.349007] Unpacking initramfs...
[    1.096691] Freeing initrd memory: 21236K
[    1.098891] PCI-DMA: Using software bounce buffering for IO (SWIOTLB)
[    1.098895] software IO TLB: mapped [mem 0xcaebd000-0xceebd000] (64MB)
[    1.099873] audit: initializing netlink subsys (disabled)
[    1.099915] audit: type=2000 audit(1576175689.988:1): initialized
[    1.100942] workingset: timestamp_bits=40 max_order=20 bucket_order=0
[    1.101004] zbud: loaded
[    1.102817] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 250)
[    1.102905] io scheduler noop registered (default)
[    1.102907] io scheduler deadline registered
[    1.102937] io scheduler cfq registered
[    1.103853] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[    1.103870] pciehp: PCI Express Hot Plug Controller Driver version: 0.4
[    1.103904] vesafb: mode is 1280x1024x32, linelength=5120, pages=0
[    1.103905] vesafb: scrolling: redraw
[    1.103909] vesafb: Truecolor: size=8:8:8:8, shift=24:16:8:0
[    1.103926] pmd_set_huge: Cannot satisfy [mem 0xcf800000-0xcfa00000] with a huge-page mapping due to MTRR override.
[    1.103962] vesafb: framebuffer at 0xcf800000, mapped to 0xffffa17981000000, using 5120k, total 5120k
[    1.145156] Console: switching to colour frame buffer device 160x64
[    1.185989] fb0: VESA VGA frame buffer device
[    1.186037] intel_idle: MWAIT substates: 0x10
[    1.186040] intel_idle: v0.4.1 model 0x36
[    1.186140] intel_idle: lapic_timer_reliable_states 0xffffffff
[    1.186375] GHES: HEST is not enabled!
[    1.186542] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
[    1.207207] 00:04: ttyS0 at I/O 0x3f8 (irq = 3, base_baud = 115200) is a 16550A
[    1.228022] 00:05: ttyS1 at I/O 0x2f8 (irq = 4, base_baud = 115200) is a 16550A
[    1.229064] Linux agpgart interface v0.103
[    1.229291] AMD IOMMUv2 driver by Joerg Roedel <jroedel@suse.de>
[    1.229293] AMD IOMMUv2 functionality not available on this system
[    1.229803] i8042: PNP: No PS/2 controller found. Probing ports directly.
[    1.232263] serio: i8042 KBD port at 0x60,0x64 irq 1
[    1.232277] serio: i8042 AUX port at 0x60,0x64 irq 12
[    1.232749] mousedev: PS/2 mouse device common for all mice
[    1.232837] rtc_cmos 00:03: RTC can wake from S4
[    1.233097] rtc_cmos 00:03: rtc core: registered rtc_cmos as rtc0
[    1.233139] rtc_cmos 00:03: alarms up to one month, y3k, 242 bytes nvram, hpet irqs
[    1.233205] ledtrig-cpu: registered to indicate activity on CPUs
[    1.233976] IPv6: Loaded, but administratively disabled, reboot required to enable
[    1.233978] mip6: Mobile IPv6
[    1.233980] mip6: mip6_init: can't add xfrm type(destopt)
[    1.233983] NET: Registered protocol family 17
[    1.233994] mpls_gso: MPLS GSO support
[    1.234432] microcode: sig=0x30661, pf=0x4, revision=0x10d
[    1.234532] microcode: Microcode Update Driver: v2.01 <tigran@aivazian.fsnet.co.uk>, Peter Oruba
[    1.234873] registered taskstats version 1
[    1.234914] zswap: loaded using pool lzo/zbud
[    1.235074] ima: No TPM chip found, activating TPM-bypass!
[    1.235079] ima: Allocated hash algorithm: sha256
[    1.235795] rtc_cmos 00:03: setting system clock to 2019-12-12 18:34:50 UTC (1576175690)
[    1.235964] PM: Hibernation image not present or could not be loaded.
[    1.238842] Freeing unused kernel memory: 1424K
[    1.238847] Write protecting the kernel read-only data: 12288k
[    1.240922] Freeing unused kernel memory: 1892K
[    1.249684] Freeing unused kernel memory: 1248K
[    1.264311] x86/mm: Checked W+X mappings: passed, no W+X pages found.
[    1.305497] udevd[70]: starting version 3.2.2
[    1.306255] random: udevd: uninitialized urandom read (16 bytes read)
[    1.306348] random: udevd: uninitialized urandom read (16 bytes read)
[    1.308594] udevd[71]: starting eudev-3.2.2
[    1.331559] random: udevd: uninitialized urandom read (16 bytes read)
[    1.365887] pps_core: LinuxPPS API ver. 1 registered
[    1.365890] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[    1.366447] PTP clock support registered
[    1.369154] e1000e: Intel(R) PRO/1000 Network Driver - 3.2.6-k
[    1.369156] e1000e: Copyright(c) 1999 - 2015 Intel Corporation.
[    1.369468] e1000e 0000:02:00.0: Interrupt Throttling Rate (ints/sec) set to dynamic conservative mode
[    1.385637] i801_smbus 0000:00:1f.3: SMBus using PCI interrupt
[    1.385673] ACPI: bus type USB registered
[    1.385763] usbcore: registered new interface driver usbfs
[    1.385796] usbcore: registered new interface driver hub
[    1.385866] usbcore: registered new device driver usb
[    1.387734] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    1.388570] uhci_hcd: USB Universal Host Controller Interface driver
[    1.391696] ehci-pci: EHCI PCI platform driver
[    1.397284] uhci_hcd 0000:00:1d.0: UHCI Host Controller
[    1.397300] uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 1
[    1.397318] uhci_hcd 0000:00:1d.0: detected 2 ports
[    1.397373] uhci_hcd 0000:00:1d.0: irq 23, io base 0x000040a0
[    1.397539] usb usb1: New USB device found, idVendor=1d6b, idProduct=0001
[    1.397544] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    1.397547] usb usb1: Product: UHCI Host Controller
[    1.397549] usb usb1: Manufacturer: Linux 4.9.189-ath-regd uhci_hcd
[    1.397552] usb usb1: SerialNumber: 0000:00:1d.0
[    1.398075] hub 1-0:1.0: USB hub found
[    1.398098] hub 1-0:1.0: 2 ports detected
[    1.398504] SCSI subsystem initialized
[    1.398979] ehci-pci 0000:00:1d.7: EHCI Host Controller
[    1.399000] ehci-pci 0000:00:1d.7: new USB bus registered, assigned bus number 2
[    1.399033] ehci-pci 0000:00:1d.7: debug port 1
[    1.402961] ehci-pci 0000:00:1d.7: cache line size of 64 is not supported
[    1.402978] ehci-pci 0000:00:1d.7: irq 23, io mem 0xd0600400
[    1.404370] e100: Intel(R) PRO/100 Network Driver, 3.5.24-k2-NAPI
[    1.404373] e100: Copyright(c) 1999-2006 Intel Corporation
[    1.404867] libata version 3.00 loaded.
[    1.416699] ehci-pci 0000:00:1d.7: USB 2.0 started, EHCI 1.00
[    1.416855] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002
[    1.416859] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    1.416862] usb usb2: Product: EHCI Host Controller
[    1.416865] usb usb2: Manufacturer: Linux 4.9.189-ath-regd ehci_hcd
[    1.416868] usb usb2: SerialNumber: 0000:00:1d.7
[    1.434210] hub 2-0:1.0: USB hub found
[    1.434224] e100 0000:04:04.0 eth0: addr 0xd0001000, irq 20, MAC addr 00:50:8b:66:35:a8
[    1.434235] hub 2-0:1.0: 8 ports detected
[    1.434339] e1000e 0000:02:00.0 0000:02:00.0 (uninitialized): registered PHC clock
[    1.468858] hub 1-0:1.0: USB hub found
[    1.468881] hub 1-0:1.0: 2 ports detected
[    1.469853] uhci_hcd 0000:00:1d.1: UHCI Host Controller
[    1.469870] uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 3
[    1.469883] uhci_hcd 0000:00:1d.1: detected 2 ports
[    1.469915] uhci_hcd 0000:00:1d.1: irq 19, io base 0x00004080
[    1.470159] usb usb3: New USB device found, idVendor=1d6b, idProduct=0001
[    1.470164] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    1.470167] usb usb3: Product: UHCI Host Controller
[    1.470170] usb usb3: Manufacturer: Linux 4.9.189-ath-regd uhci_hcd
[    1.470172] usb usb3: SerialNumber: 0000:00:1d.1
[    1.470512] e100 0000:04:05.0 eth1: addr 0xd0000000, irq 21, MAC addr 00:50:8b:66:35:a9
[    1.470689] hub 3-0:1.0: USB hub found
[    1.470971] hub 3-0:1.0: 2 ports detected
[    1.471569] uhci_hcd 0000:00:1d.2: UHCI Host Controller
[    1.471583] uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 4
[    1.471599] uhci_hcd 0000:00:1d.2: detected 2 ports
[    1.471647] uhci_hcd 0000:00:1d.2: irq 18, io base 0x00004060
[    1.473812] usb usb4: New USB device found, idVendor=1d6b, idProduct=0001
[    1.473817] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    1.473821] usb usb4: Product: UHCI Host Controller
[    1.473824] usb usb4: Manufacturer: Linux 4.9.189-ath-regd uhci_hcd
[    1.473826] usb usb4: SerialNumber: 0000:00:1d.2
[    1.474967] hub 4-0:1.0: USB hub found
[    1.474989] hub 4-0:1.0: 2 ports detected
[    1.476296] ahci 0000:00:1f.2: version 3.0
[    1.476609] ahci 0000:00:1f.2: SSS flag set, parallel bus scan disabled
[    1.476649] ahci 0000:00:1f.2: AHCI 0001.0100 32 slots 4 ports 3 Gbps 0x3 impl SATA mode
[    1.476693] ahci 0000:00:1f.2: flags: 64bit ncq stag pm led clo pio slum part 
[    1.482476] scsi host0: ahci
[    1.483841] scsi host1: ahci
[    1.485251] scsi host2: ahci
[    1.485580] scsi host3: ahci
[    1.485744] ata1: SATA max UDMA/133 abar m1024@0xd0600000 port 0xd0600100 irq 29
[    1.485748] ata2: SATA max UDMA/133 abar m1024@0xd0600000 port 0xd0600180 irq 29
[    1.485750] ata3: DUMMY
[    1.485752] ata4: DUMMY
[    1.486056] uhci_hcd 0000:00:1d.3: UHCI Host Controller
[    1.486075] uhci_hcd 0000:00:1d.3: new USB bus registered, assigned bus number 5
[    1.486088] uhci_hcd 0000:00:1d.3: detected 2 ports
[    1.486140] uhci_hcd 0000:00:1d.3: irq 16, io base 0x00004040
[    1.486358] usb usb5: New USB device found, idVendor=1d6b, idProduct=0001
[    1.486362] usb usb5: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    1.486365] usb usb5: Product: UHCI Host Controller
[    1.486368] usb usb5: Manufacturer: Linux 4.9.189-ath-regd uhci_hcd
[    1.486371] usb usb5: SerialNumber: 0000:00:1d.3
[    1.486772] hub 5-0:1.0: USB hub found
[    1.486799] hub 5-0:1.0: 2 ports detected
[    1.495882] e1000e 0000:02:00.0 eth2: (PCI Express:2.5GT/s:Width x1) 00:22:4d:a6:e2:25
[    1.495886] e1000e 0000:02:00.0 eth2: Intel(R) PRO/1000 Network Connection
[    1.495903] e1000e 0000:02:00.0 eth2: MAC: 3, PHY: 8, PBA No: FFFFFF-0FF
[    1.496218] e1000e 0000:01:00.0: Interrupt Throttling Rate (ints/sec) set to dynamic conservative mode
[    1.553268] e1000e 0000:01:00.0 0000:01:00.0 (uninitialized): registered PHC clock
[    1.616215] e1000e 0000:01:00.0 eth3: (PCI Express:2.5GT/s:Width x1) 00:22:4d:a6:e2:29
[    1.616219] e1000e 0000:01:00.0 eth3: Intel(R) PRO/1000 Network Connection
[    1.616236] e1000e 0000:01:00.0 eth3: MAC: 3, PHY: 8, PBA No: FFFFFF-0FF
[    1.799138] ata1: SATA link down (SStatus 0 SControl 300)
[    2.111152] ata2: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[    2.111867] ata2.00: ATA-7: SAMSUNG SSD UM410 Series 2.5" 16GB, VAM12D1Q, max UDMA/100
[    2.111870] ata2.00: 31277232 sectors, multi 16: LBA48 
[    2.112074] ata2.00: configured for UDMA/100
[    2.112404] scsi 1:0:0:0: Direct-Access     ATA      SAMSUNG SSD UM41 2D1Q PQ: 0 ANSI: 5
[    2.124757] tsc: Refined TSC clocksource calibration: 1866.732 MHz
[    2.124766] clocksource: tsc: mask: 0xffffffffffffffff max_cycles: 0x35d0d1b66a8, max_idle_ns: 881590563120 ns
[    2.145554] sd 1:0:0:0: [sda] 31277232 512-byte logical blocks: (16.0 GB/14.9 GiB)
[    2.145679] sd 1:0:0:0: [sda] Write Protect is off
[    2.145685] sd 1:0:0:0: [sda] Mode Sense: 00 3a 00 00
[    2.145737] sd 1:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[    2.146956]  sda: sda1
[    2.147649] sd 1:0:0:0: [sda] Attached SCSI disk
[    2.148915] sd 1:0:0:0: Attached scsi generic sg0 type 0
[    2.381207] EXT4-fs (sda1): mounting ext2 file system using the ext4 subsystem
[    2.384331] EXT4-fs (sda1): mounted filesystem without journal. Opts: (null)
[    2.547700] random: fast init done
[    3.013635] udevd[339]: starting version 3.2.2
[    3.025225] random: udevd: uninitialized urandom read (16 bytes read)
[    3.025840] random: udevd: uninitialized urandom read (16 bytes read)
[    3.025866] random: udevd: uninitialized urandom read (16 bytes read)
[    3.044358] udevd[340]: starting eudev-3.2.2
[    3.148979] clocksource: Switched to clocksource tsc
[    3.165572] ACPI Warning: SystemIO range 0x0000000000000428-0x000000000000042F conflicts with OpRegion 0x0000000000000400-0x000000000000047F (\PMIO) (20160831/utaddress-247)
[    3.165586] ACPI Warning: SystemIO range 0x0000000000000428-0x000000000000042F conflicts with OpRegion 0x0000000000000400-0x000000000000042F (\SWC1) (20160831/utaddress-247)
[    3.165596] ACPI: If an ACPI driver is available for this device, you should use it instead of the native driver
[    3.165600] ACPI Warning: SystemIO range 0x0000000000000530-0x000000000000053F conflicts with OpRegion 0x0000000000000500-0x000000000000053B (\GPIO) (20160831/utaddress-247)
[    3.165608] ACPI: If an ACPI driver is available for this device, you should use it instead of the native driver
[    3.165610] ACPI Warning: SystemIO range 0x0000000000000500-0x000000000000052F conflicts with OpRegion 0x0000000000000500-0x000000000000053B (\GPIO) (20160831/utaddress-247)
[    3.165618] ACPI: If an ACPI driver is available for this device, you should use it instead of the native driver
[    3.165620] lpc_ich: Resource conflict(s) found affecting gpio_ich
[    3.165915] input: Power Button as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0C:00/input/input3
[    3.165923] ACPI: Power Button [PWRB]
[    3.166059] input: Sleep Button as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0E:00/input/input4
[    3.166064] ACPI: Sleep Button [SLPB]
[    3.166193] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input5
[    3.166198] ACPI: Power Button [PWRF]
[    3.169783] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
[    3.294163] input: PC Speaker as /devices/platform/pcspkr/input/input6
[    3.397608] iTCO_vendor_support: vendor-support=0
[    3.398834] iTCO_wdt: Intel TCO WatchDog Timer Driver v1.11
[    3.398908] iTCO_wdt: Found a NM10 TCO device (Version=2, TCOBASE=0x0460)
[    3.400023] iTCO_wdt: initialized. heartbeat=30 sec (nowayout=0)
[    4.510725] ip_tables: (C) 2000-2006 Netfilter Core Team
[    4.524684] nf_conntrack version 0.5.0 (16384 buckets, 65536 max)
[    5.348186] bridge: filtering via arp/ip/ip6tables is no longer available by default. Update your scripts to load br_netfilter if you need this.
[    5.359258] br0: port 1(eth1) entered blocking state
[    5.359276] br0: port 1(eth1) entered disabled state
[    5.359433] device eth1 entered promiscuous mode
[    5.385196] e100 0000:04:05.0 eth1: NIC Link is Up 100 Mbps Full Duplex
[    5.385586] br0: port 1(eth1) entered blocking state
[    5.385591] br0: port 1(eth1) entered forwarding state
[    6.469284] e100 0000:04:04.0 eth0: NIC Link is Up 100 Mbps Full Duplex
[    6.718009] e1000e: eth2 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: None
[    6.974155] EXT4-fs (sda1): re-mounted. Opts: errors=remount-ro,discard,commit=60
[    7.407822] w83627ehf: Found W83627UHG chip at 0x290
[    7.838650] urandom_read: 3 callbacks suppressed
[    7.838654] random: dd: uninitialized urandom read (512 bytes read)
[   11.513211] PPP generic driver version 2.4.2
[   11.518118] NET: Registered protocol family 24
[   11.548442] l2tp_core: L2TP core driver, V2.0
[   11.550012] l2tp_netlink: L2TP netlink interface
[   11.552313] l2tp_ppp: PPPoL2TP kernel driver, V2.0
[   11.605333] elogind[1962]: New seat seat0.
[   11.608529] elogind[1962]: Watching system buttons on /dev/input/event2 (Power Button)
[   11.608737] elogind[1962]: Watching system buttons on /dev/input/event0 (Power Button)
[   11.608935] elogind[1962]: Watching system buttons on /dev/input/event1 (Sleep Button)
[  116.897894] random: crng init done
[  169.183114] elogind[1962]: New session 1 of user deuser.

 

deuser
()

WLE900VX (QCA9880) + hostapd?

Форум — Linux-hardware

Интерес ваш опыт по такой связке. В плане работы с hostapd и 802.11ac. Стоит ли покупать и вообще связываться с QCA9880. Другие варианты? Есть ли подводные камни?

 , ,

deuser
()

Intel x520-da1

Форум — Linux-hardware

Есть две такие сетевые карты. Если соединить их между собой твинаксиальным кабелем напрямую друг к другу. Это будет работать? Какие есть подводные камни и что еще нужно учесть? Хотелось получить максимально быстрый линк между NAS и основным рабочим ПК.

 

deuser
()

Сервер факс сообщений. (hylafax)

Форум — Admin

Настроил сервер факс сообщений. Использую hylafax и простенький модем acorp 56000. Факсы принимаются, но есть проблема. Как реализовать эту функцию «телефон\факс», когда на одной линии телефон и факс. То-есть, факс должен распознавать приветствие факс с той стороны, а иначе... молчать. Сейчас получается, что он поднимает трубку и гудит в линию даже если там не факс?? Такое кто-то настраивал с hylafax?

deuser
()

RSS подписка на новые темы