Накатил centos7 и хотел настроить wifi через свисток, но ОС определяет его как eth-карту
enp0s4f1u3: <NO-CARRIER,BROADCAST,MULTICAST,UP> mtu 1500 qdisc pfifo_fast state DOWN qlen 1000
link/ether 00:e0:4c:03:f3:22 brd ff:ff:ff:ff:ff:ff
хотя в убунте этот же свисток определяется как wifi карта Как сию беду в Центосе победить то?
dmesg Centos7
[ 352.756057] usb 1-3: new high-speed USB device number 4 using ehci-pci
[ 352.873041] usb 1-3: New USB device found, idVendor=0bda, idProduct=8171
[ 352.873052] usb 1-3: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 352.873058] usb 1-3: Product: RTL8188S WLAN Adapter
[ 352.873064] usb 1-3: Manufacturer: Manufacturer Realtek
[ 352.873070] usb 1-3: SerialNumber: 00e04c000001
[ 352.877125] r8712u: Staging version
[ 352.877183] r8712u: register rtl8712_netdev_ops to netdev_ops
[ 352.877201] usb 1-3: r8712u: USB_SPEED_HIGH with 4 endpoints
[ 352.877943] usb 1-3: r8712u: Boot from EFUSE: Autoload OK
[ 353.575542] usb 1-3: r8712u: CustomerID = 0x0000
[ 353.575554] usb 1-3: r8712u: MAC Address from efuse = 00:e0:4c:03:f3:22
[ 353.575562] usb 1-3: r8712u: Loading firmware from "rtlwifi/rtl8712u.bin"
[ 353.641542] IPv6: ADDRCONF(NETDEV_UP): enp0s4f1u3: link is not ready
[ 354.333793] r8712u 1-3:1.0 enp0s4f1u3: 1 RCR=0x153f00e
[ 354.334554] r8712u 1-3:1.0 enp0s4f1u3: 2 RCR=0x553f00e
[ 354.440755] IPv6: ADDRCONF(NETDEV_UP): enp0s4f1u3: link is not ready
[ 354.448252] IPv6: ADDRCONF(NETDEV_UP): enp0s4f1u3: link is not ready
dmesg Ubuntu
[1845410.148369] usb 1-4: new high-speed USB device number 126 using xhci_hcd
[1845410.278641] usb 1-4: New USB device found, idVendor=0bda, idProduct=8171
[1845410.278649] usb 1-4: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[1845410.278654] usb 1-4: Product: RTL8188S WLAN Adapter
[1845410.278657] usb 1-4: Manufacturer: Manufacturer Realtek
[1845410.278660] usb 1-4: SerialNumber: 00e04c000001
[1845410.279549] r8712u: Staging version
[1845410.279580] r8712u: register rtl8712_netdev_ops to netdev_ops
[1845410.279587] usb 1-4: r8712u: USB_SPEED_HIGH with 4 endpoints
[1845410.280014] usb 1-4: r8712u: Boot from EFUSE: Autoload OK
[1845410.641489] usb 1-4: r8712u: CustomerID = 0x0000
[1845410.641500] usb 1-4: r8712u: MAC Address from efuse = 00:e0:4c:03:f3:22
[1845410.641505] usb 1-4: r8712u: Loading firmware from "rtlwifi/rtl8712u.bin"
[1845412.437880] r8712u 1-4:1.0 wlan1: 1 RCR=0x153f00e
[1845412.438416] r8712u 1-4:1.0 wlan1: 2 RCR=0x553f00e
[1845594.638476] usb 1-4: USB disconnect, device number 126
