LINUX.ORG.RU

USB & SCSI emulation


0

0

Gentoo, kernel 2.6.15. Всё сделал по официальной хаутушке: http://www.gentoo.org/doc/en/usb-guide.xml. Все необхдимый модули вкомпилировал в ядро. Ядро не включает емуляцию скази для USB. dmesg, в часности, показывает, что вот это:

(SCSI emulation automatically kicks in)
scsi0 : SCSI emulation for USB Mass Storage devices
usb-storage: device found at 2

(Now the device information including model number is retrieved)
usb-storage: waiting for device to settle before scanning
Vendor: JetFlash Model: TS512MJF2A Rev: 1.00
Type: Direct-Access ANSI SCSI revision: 02
SCSI device sda: 1003600 512-byte hdwr sectors (514 MB)

(The write-protect sense is EXPERIMENTAL code in the later kernels)
sda: Write Protect is off
sda: Mode Sense: 0b 00 00 08
sda: assuming drive cache: write through
SCSI device sda: 1003600 512-byte hdwr sectors (514 MB)
/dev/scsi/host0/bus0/target0/lun0: p1
Attached scsi removable disk sda at scsi0, channel 0, id 0, lun 0
Attached scsi generic sg0 at scsi0, channel 0, id 0, lun 0, type 0
usb-storage: device scan complete
(At this point, the device is generally accessible by mounting /dev/sda1)

отсутствует. Несмотря на то, что вот эти опции в ядре:

Device Drivers --->
SCSI device support --->

(Although SCSI will be enabled automatically when selecting USB Mass Storage,
we need to enable disk support.)
--- SCSI support type (disk, tape, CD-ROM)
<*> SCSI disk support

были включены в ядре. Как мне включить эмуляцию скази? Сообщением ниже полный листинг dmesg.

★★★

Linux version 2.6.15-gentoo-r1 (root@elive) (gcc version 3.4.4 (Gentoo 3.4.4-r1, ssp-3.4.4-1.0, pie-8.7.8)) #2 SMP PREEMPT Thu Apr 20 21:19:58 CEST 2006
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000e0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000001ffd0000 (usable)
BIOS-e820: 000000001ffd0000 - 000000001ffdf000 (ACPI data)
BIOS-e820: 000000001ffdf000 - 0000000020000000 (ACPI NVS)
BIOS-e820: 00000000fff80000 - 0000000100000000 (reserved)
511MB LOWMEM available.
found SMP MP-table at 000ff780
On node 0 totalpages: 131024
DMA zone: 4096 pages, LIFO batch:0
DMA32 zone: 0 pages, LIFO batch:0
Normal zone: 126928 pages, LIFO batch:31
HighMem zone: 0 pages, LIFO batch:0
DMI 2.3 present.
ACPI: RSDP (v000 ACPIAM ) @ 0x000f54e0
ACPI: RSDT (v001 A M I OEMRSDT 0x06000308 MSFT 0x00000097) @ 0x1ffd0000
ACPI: FADT (v002 A M I OEMFACP 0x06000308 MSFT 0x00000097) @ 0x1ffd0200
ACPI: MADT (v001 A M I OEMAPIC 0x06000308 MSFT 0x00000097) @ 0x1ffd0390
ACPI: OEMB (v001 A M I AMI_OEM 0x06000308 MSFT 0x00000097) @ 0x1ffdf040
ACPI: DSDT (v001 UW FSC_____ 0x00000016 INTL 0x02002026) @ 0x00000000
ACPI: Local APIC address 0xfee00000
ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
Processor #0 15:2 APIC version 20
ACPI: LAPIC (acpi_id[0x02] lapic_id[0x81] disabled)
ACPI: IOAPIC (id[0x01] address[0xfec00000] gsi_base[0])
IOAPIC[0]: apic_id 1, version 32, address 0xfec00000, GSI 0-23
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
ACPI: IRQ0 used by override.
ACPI: IRQ2 used by override.
ACPI: IRQ9 used by override.
Enabling APIC mode: Flat. Using 1 I/O APICs
Using ACPI (MADT) for SMP configuration information
Allocating PCI resources starting at 30000000 (gap: 20000000:dff80000)
Built 1 zonelists
Kernel command line: root=/dev/hda8
mapped APIC to ffffd000 (fee00000)
mapped IOAPIC to ffffc000 (fec00000)
Initializing CPU#0
PID hash table entries: 2048 (order: 11, 32768 bytes)
Detected 2798.398 MHz processor.
Using tsc for high-res timesource
Console: colour VGA+ 80x25
Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
Memory: 513032k/524096k available (3360k kernel code, 10532k reserved, 1006k data, 240k init, 0k highmem)
Checking if this processor honours the WP bit even in supervisor mode... Ok.
Calibrating delay using timer specific routine.. 5604.70 BogoMIPS (lpj=11209406)
Mount-cache hash table entries: 512
CPU: After generic identify, caps: bfebfbff 00000000 00000000 00000000 00004400 00000000 00000000
CPU: After vendor identify, caps: bfebfbff 00000000 00000000 00000000 00004400 00000000 00000000
CPU: Trace cache: 12K uops, L1 D cache: 8K
CPU: L2 cache: 512K
CPU: Hyper-Threading is disabled
CPU: After all inits, caps: bfebfbff 00000000 00000000 00000080 00004400 00000000 00000000
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
CPU0: Intel P4/Xeon Extended MCE MSRs (12) available
CPU0: Thermal monitoring enabled
mtrr: v2.0 (20020519)
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Checking 'hlt' instruction... OK.
CPU0: Intel(R) Pentium(R) 4 CPU 2.80GHz stepping 07
Total of 1 processors activated (5604.70 BogoMIPS).
ENABLING IO-APIC IRQs
..TIMER: vector=0x31 apic1=0 pin1=2 apic2=-1 pin2=-1
Brought up 1 CPUs
NET: Registered protocol family 16
ACPI: bus type pci registered
PCI: PCI BIOS revision 2.10 entry at 0xf0031, last bus=2
PCI: Using configuration type 1
ACPI: Subsystem revision 20050902
ACPI: Interpreter enabled
ACPI: Using IOAPIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (0000:00)
PCI: Probing PCI hardware (bus 00)
PCI quirk: region 0400-047f claimed by ICH4 ACPI/GPIO/TCO
PCI quirk: region 0500-053f claimed by ICH4 GPIO
PCI: Ignoring BAR0-3 of IDE controller 0000:00:1f.1
Boot video device is 0000:01:00.0
PCI: Transparent bridge - 0000:00:1e.0
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P2._PRT]
ACPI: Power Resource [URP1] (off)
ACPI: Power Resource [URP2] (off)
ACPI: Power Resource [FDDP] (off)
ACPI: Power Resource [LPTP] (off)
ACPI: Embedded Controller [EC0] (gpe 28)
ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 9 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LNKB] (IRQs *3 4 5 6 7 9 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 7 *9 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 *5 6 7 9 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 9 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 9 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 6 7 9 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 6 7 9 *10 11 12 14 15)
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
pnp: PnP ACPI: found 10 devices
SCSI subsystem initialized
usbcore: registered new driver usbfs
usbcore: registered new driver hub
PCI: Using ACPI for IRQ routing
PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report
NET: Registered protocol family 23
pnp: 00:05: ioport range 0x1100-0x113f has been reserved
pnp: 00:05: ioport range 0x1254-0x1254 has been reserved
pnp: 00:05: ioport range 0x12d4-0x12d4 has been reserved
pnp: 00:05: ioport range 0x1300-0x1375 has been reserved
pnp: 00:05: ioport range 0x1377-0x137f has been reserved
PCI: Bridge: 0000:00:01.0
IO window: b000-bfff
MEM window: ffc00000-ffcfffff
PREFETCH window: ceb00000-deafffff
PCI: Bus 3, cardbus bridge: 0000:02:03.0
IO window: 0000c000-0000c0ff
IO window: 0000c400-0000c4ff
PREFETCH window: 30000000-31ffffff
MEM window: 34000000-35ffffff
PCI: Bridge: 0000:00:1e.0
IO window: c000-cfff
MEM window: ffd00000-ffdfffff
PREFETCH window: 30000000-32ffffff
PCI: Setting latency timer of device 0000:00:1e.0 to 64
ACPI: PCI Interrupt 0000:02:03.0[A] -> GSI 17 (level, low) -> IRQ 16
PCI: Setting latency timer of device 0000:02:03.0 to 64
Machine check exception polling timer started.
audit: initializing netlink socket (disabled)
audit(1146180338.596:1): initialized
Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
Initializing Cryptographic API
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered
0000:00:1d.7 EHCI: early BIOS handoff failed (BIOS bug ?)
ACPI: PCI Interrupt 0000:01:00.0[A] -> GSI 16 (level, low) -> IRQ 17
radeonfb: Retreived PLL infos from BIOS
radeonfb: Reference=27.00 MHz (RefDiv=12) Memory=240.00 Mhz, System=220.00 MHz
radeonfb: PLL min 20000 max 35000
Non-DDC laptop panel detected
radeonfb: Monitor 1 type LCD found
radeonfb: Monitor 2 type no found
radeonfb: panel ID string: 1024x768
radeonfb: detected LVDS panel size from BIOS: 1024x768
radeondb: BIOS provided dividers will be used
radeonfb: Dynamic Clock Power Management enabled
Console: switching to colour frame buffer device 128x48
radeonfb (0000:01:00.0): ATI Radeon Lf
vesafb: ATI Technologies Inc., M9 , 01.00 (OEM: ATI MOBILITY RADEON 9000)
vesafb: VBE version: 2.0
vesafb: no monitor limits have been set
vesafb: scrolling: redraw
vesafb: cannot reserve video memory at 0xd0000000
vesafb: framebuffer at 0xd0000000, mapped to 0xe1900000, using 6144k, total 65536k

eRazor ★★★
() автор топика
Ответ на: комментарий от eRazor

fb1: VESA VGA frame buffer device
ACPI: AC Adapter [AC0] (on-line)
ACPI: Battery Slot [BAT0] (battery absent)
ACPI: Power Button (FF) [PWRF]
ACPI: Lid Switch [LID]
ACPI: Sleep Button (CM) [SLPB]
ACPI: Power Button (CM) [PWRB]
ACPI: Video Device [VGA] (multi-head: yes rom: no post: no)
ACPI: Processor [CPU1] (supports 8 throttling states)
ACPI: Thermal Zone [THRM] (75 C)
lp: driver loaded but no devices found
Linux agpgart interface v0.101 (c) Dave Jones
agpgart: Detected an Intel 845G Chipset.
agpgart: AGP aperture is 256M @ 0xe0000000
[drm] Initialized drm 1.0.0 20040925
PNP: PS/2 Controller [PNP030b:PS2K,PNP0f03:PS2M] at 0x60,0x64 irq 1,12
i8042.c: Detected active multiplexing controller, rev 1.0.
serio: i8042 AUX0 port at 0x60,0x64 irq 12
serio: i8042 AUX1 port at 0x60,0x64 irq 12
serio: i8042 AUX2 port at 0x60,0x64 irq 12
serio: i8042 AUX3 port at 0x60,0x64 irq 12
serio: i8042 KBD port at 0x60,0x64 irq 1
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing disabled
ACPI: PCI Interrupt 0000:00:1f.6[B] -> GSI 17 (level, low) -> IRQ 16
ACPI: PCI interrupt for device 0000:00:1f.6 disabled
parport: PnPBIOS parport detected.
parport0: PC-style at 0x378, irq 7 [PCSPP(,...)]
lp0: using parport0 (interrupt-driven).
mice: PS/2 mouse device common for all mice
input: AT Translated Set 2 keyboard as /class/input/input0
Synaptics Touchpad, model: 1, fw: 4.1, id: 0x848a1, caps: 0x0/0x0
input: SynPS/2 Synaptics TouchPad as /class/input/input1
input: ImPS/2 Generic Wheel Mouse as /class/input/input2
floppy0: no floppy controllers found
loop: loaded (max 8 devices)
usbcore: registered new driver ub
natsemi dp8381x driver, version 1.07+LK1.0.17, Sep 27, 2002
originally by Donald Becker <becker@scyld.com>
http://www.scyld.com/network/natsemi.html
2.4.x kernel port by Jeff Garzik, Tjeerd Mulder
ACPI: PCI Interrupt 0000:02:0c.0[A] -> GSI 17 (level, low) -> IRQ 16
natsemi eth0: NatSemi DP8381[56] at 0xffdfe000 (0000:02:0c.0), 00:a0:cc:dc:12:60, IRQ 16, port TP.
PPP generic driver version 2.4.2
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
ICH4: IDE controller at PCI slot 0000:00:1f.1
PCI: Enabling device 0000:00:1f.1 (0005 -> 0007)
ACPI: PCI Interrupt 0000:00:1f.1[A] -> GSI 18 (level, low) -> IRQ 18
ICH4: chipset revision 2
ICH4: not 100% native mode: will probe irqs later
ide0: BM-DMA at 0xffa0-0xffa7, BIOS settings: hda:DMA, hdb:pio
ide1: BM-DMA at 0xffa8-0xffaf, BIOS settings: hdc:DMA, hdd:pio
Probing IDE interface ide0...
hda: IC25N060ATMR04-0, ATA DISK drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
Probing IDE interface ide1...
hdc: DVD+RW RW8160, ATAPI CD/DVD-ROM drive
ide1 at 0x170-0x177,0x376 on irq 15
hda: max request size: 1024KiB
hda: 117210240 sectors (60011 MB) w/7884KiB Cache, CHS=16383/255/63, UDMA(100)
hda: cache flushes supported
hda: hda1 hda2 hda3 < hda5 hda6 hda7 hda8 >
hdc: ATAPI 24X DVD-ROM CD-R/RW drive, 8192kB Cache, UDMA(33)
Uniform CD-ROM driver Revision: 3.20
libata version 1.20 loaded.
ohci1394: $Rev: 1313 $ Ben Collins <bcollins@debian.org>
ACPI: PCI Interrupt 0000:02:0a.0[A] -> GSI 18 (level, low) -> IRQ 18
PCI: Via IRQ fixup for 0000:02:0a.0, from 9 to 2
ohci1394: fw-host0: OHCI-1394 1.1 (PCI): IRQ=[18] MMIO=[ffdff800-ffdfffff] Max Packet=[2048]
ieee1394: raw1394: /dev/raw1394 device initialized
usbmon: debugfs is not available
ACPI: PCI Interrupt 0000:00:1d.7[D] -> GSI 23 (level, low) -> IRQ 19
PCI: Setting latency timer of device 0000:00:1d.7 to 64
ehci_hcd 0000:00:1d.7: EHCI Host Controller
ehci_hcd 0000:00:1d.7: debug port 1
PCI: cache line size of 128 is not supported by device 0000:00:1d.7
ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 1
ehci_hcd 0000:00:1d.7: irq 19, io mem 0xffeffc00
ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 6 ports detected
USB Universal Host Controller Interface driver v2.3
ACPI: PCI Interrupt 0000:00:1d.0[A] -> GSI 16 (level, low) -> IRQ 17
PCI: Setting latency timer of device 0000:00:1d.0 to 64
uhci_hcd 0000:00:1d.0: UHCI Host Controller
uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 2
uhci_hcd 0000:00:1d.0: irq 17, io base 0x0000df20
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:1d.1[B] -> GSI 19 (level, low) -> IRQ 20
PCI: Setting latency timer of device 0000:00:1d.1 to 64
uhci_hcd 0000:00:1d.1: UHCI Host Controller
uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 3
uhci_hcd 0000:00:1d.1: irq 20, io base 0x0000df40
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
usb 1-6: new high speed USB device using ehci_hcd and address 2
ACPI: PCI Interrupt 0000:00:1d.2[C] -> GSI 18 (level, low) -> IRQ 18
PCI: Setting latency timer of device 0000:00:1d.2 to 64
uhci_hcd 0000:00:1d.2: UHCI Host Controller
uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 4
uhci_hcd 0000:00:1d.2: irq 18, io base 0x0000df80
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 2 ports detected
ub(1.2): GetMaxLUN returned 0, using 1 LUNs
uba: uba1

eRazor ★★★
() автор топика
Ответ на: комментарий от eRazor

usbcore: registered new driver usblp
drivers/usb/class/usblp.c: v0.13: USB Printer Device Class driver
Initializing USB Mass Storage driver...
usbcore: registered new driver usb-storage
USB Mass Storage support registered.
usbcore: registered new driver usbhid
drivers/usb/input/hid-core.c: v2.6:USB HID core driver
Advanced Linux Sound Architecture Driver Version 1.0.10rc3 (Mon Nov 07 13:30:21 2005 UTC).
PCI: Enabling device 0000:00:1f.5 (0005 -> 0007)
ACPI: PCI Interrupt 0000:00:1f.5[B] -> GSI 17 (level, low) -> IRQ 16
PCI: Setting latency timer of device 0000:00:1f.5 to 64
ieee1394: Host added: ID:BUS[0-00:1023] GUID[00030d49755100fc]
intel8x0_measure_ac97_clock: measured 59381 usecs
intel8x0: clocking to 48000
ACPI: PCI Interrupt 0000:00:1f.6[B] -> GSI 17 (level, low) -> IRQ 16
PCI: Setting latency timer of device 0000:00:1f.6 to 64
ALSA device list:
#0: Intel 82801DB-ICH4 with VIA1612A at 0x33000400, irq 16
#1: Intel 82801DB-ICH4 Modem at 0xe200, irq 16
oprofile: using NMI interrupt.
NET: Registered protocol family 2
IP route cache hash table entries: 8192 (order: 3, 32768 bytes)
TCP established hash table entries: 32768 (order: 6, 393216 bytes)
TCP bind hash table entries: 32768 (order: 6, 393216 bytes)
TCP: Hash tables configured (established 32768 bind 32768)
TCP reno registered
ip_conntrack version 2.4 (4094 buckets, 32752 max) - 212 bytes per conntrack
ip_tables: (C) 2000-2002 Netfilter core team
ipt_recent v0.3.1: Stephen Frost <sfrost@snowman.net>. http://snowman.net/projects/ipt_recent/
arp_tables: (C) 2002 David S. Miller
TCP bic registered
NET: Registered protocol family 1
NET: Registered protocol family 17
Using IPI Shortcut mode
ReiserFS: hda8: found reiserfs format "3.6" with standard journal
ReiserFS: hda8: using ordered data mode
ReiserFS: hda8: journal params: device hda8, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30
ReiserFS: hda8: checking transaction log (hda8)
ReiserFS: hda8: Using r5 hash to sort names
VFS: Mounted root (reiserfs filesystem) readonly.
Freeing unused kernel memory: 240k freed
ub(1.2): resid 2048 len 2048 act 2048
end_request: I/O error, dev uba, sector 507928
Buffer I/O error on device uba1, logical block 126974
ub(1.2): resid 2048 len 2048 act 2048
end_request: I/O error, dev uba, sector 507928
Buffer I/O error on device uba1, logical block 126974
ub(1.2): resid 2048 len 2048 act 2048
end_request: I/O error, dev uba, sector 507928
Buffer I/O error on device uba1, logical block 126974
ub(1.2): resid 2048 len 2048 act 2048
end_request: I/O error, dev uba, sector 507928
Buffer I/O error on device uba1, logical block 126974
ub(1.2): resid 2048 len 2048 act 2048
end_request: I/O error, dev uba, sector 507928
Buffer I/O error on device uba1, logical block 126974
ub(1.2): resid 2048 len 2048 act 2048
end_request: I/O error, dev uba, sector 507928
Buffer I/O error on device uba1, logical block 126974
ub(1.2): resid 4096 len 4096 act 4096
end_request: I/O error, dev uba, sector 507912
Buffer I/O error on device uba1, logical block 126970
Buffer I/O error on device uba1, logical block 126971
ub(1.2): resid 4096 len 4096 act 4096
end_request: I/O error, dev uba, sector 507912
Buffer I/O error on device uba1, logical block 126970
Buffer I/O error on device uba1, logical block 126971
ub(1.2): resid 4096 len 4096 act 4096
end_request: I/O error, dev uba, sector 507920
ub(1.2): resid 4096 len 4096 act 4096
end_request: I/O error, dev uba, sector 507920
Adding 755044k swap on /dev/hda2. Priority:-1 extents:1 across:755044k
ACPI: PCI Interrupt 0000:01:00.0[A] -> GSI 16 (level, low) -> IRQ 17
[drm] Initialized radeon 1.19.0 20050911 on minor 0:
ReiserFS: hda7: found reiserfs format "3.6" with standard journal
ReiserFS: hda7: using ordered data mode
ReiserFS: hda7: journal params: device hda7, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30
ReiserFS: hda7: checking transaction log (hda7)
ReiserFS: hda7: Using r5 hash to sort names
eth0: DSPCFG accepted after 0 usec.
eth0: remaining active for wake-on-lan
psmouse.c: Wheel Mouse at isa0060/serio4/input0 lost synchronization, throwing 1 bytes away.

eRazor ★★★
() автор топика
Ответ на: комментарий от eRazor

Ах да, флэшка, ессно, воткнута. lsusb опознаёт её и показывает, что оно подключено к шине. В общем, не знаю как монтировать, мне кажется, что проблема в том, что нет эмуляции скази для USB.

eRazor ★★★
() автор топика
Ответ на: комментарий от eRazor

Должна быть. У меня стоит USB Mass Storage и SCSI Disk Support. И работает. Больше ничего вроде и не надо. Если только какие-нибудь подмодули USB Mass Storage.

Iocr
()
Вы не можете добавлять комментарии в эту тему. Тема перемещена в архив.