Здравствуйте, 2 месяца назад установил Debian 9 на новый ноутбук. И буквально вчера заметил что Seek_Error_Rate постоянно растет. По ~60 пунктов в минуту (в простое). При перезагрузке +5000 пунктов. При чем Seek_Error_Rate доходит до 65535 и сбрасывается. Диск TOSHIBA MQ04ABF100. Так-же Power-Off_Retract_Count = 188978561068. Это баг, глюк или так и должно быть?
SMART Attributes Data Structure revision number: 32
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x002f 100 100 050 Pre-fail Always - 6
3 Spin_Up_Time 0x0023 100 100 002 Pre-fail Always - 1297
4 Start_Stop_Count 0x0032 100 100 000 Old_age Always - 680
5 Reallocated_Sector_Ct 0x0033 100 100 005 Pre-fail Always - 0
7 Seek_Error_Rate 0x002f 100 100 070 Pre-fail Always - 31630
9 Power_On_Hours 0x0032 100 100 000 Old_age Always - 538
10 Spin_Retry_Count 0x0033 100 100 050 Pre-fail Always - 0
12 Power_Cycle_Count 0x0032 100 100 000 Old_age Always - 678
183 Runtime_Bad_Block 0x0032 100 100 000 Old_age Always - 53
184 End-to-End_Error 0x003b 100 100 097 Pre-fail Always - 0
187 Reported_Uncorrect 0x0032 100 100 000 Old_age Always - 0
188 Command_Timeout 0x0032 100 100 000 Old_age Always - 0
189 High_Fly_Writes 0x003a 100 100 000 Old_age Always - 0
191 G-Sense_Error_Rate 0x0032 001 001 000 Old_age Always - 166
192 Power-Off_Retract_Count 0x0032 100 100 000 Old_age Always - 188978561068
193 Load_Cycle_Count 0x0032 098 098 000 Old_age Always - 4461
194 Temperature_Celsius 0x0022 031 045 000 Old_age Always - 31 (Min/Max 27/32)
197 Current_Pending_Sector 0x0032 100 100 000 Old_age Always - 0
198 Offline_Uncorrectable 0x0030 100 100 000 Old_age Offline - 0
199 UDMA_CRC_Error_Count 0x0032 100 100 000 Old_age Always - 0
SMART Error Log Version: 1
No Errors Logged
SMART Self-test log structure revision number 1
Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error
# 1 Extended offline Aborted by host 90% 535 -
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
