Используется hylafax 4.4.1. И зюхелевский модем. Так вот, где то после 10 факсов, сыпется такое: ... Sep 11 14:00:08.33: [ 3949]: RECV received frame number 19 Sep 11 14:00:08.48: [ 3949]: RECV received frame number 20 Sep 11 14:00:08.61: [ 3949]: Bad HDLC terminating flag received. Sep 11 14:00:38.62: [ 3949]: Timeout awaiting synchronization sequence Sep 11 14:00:38.62: [ 3949]: Bad HDLC terminating flag received. Sep 11 14:01:08.00: [ 3949]: Timeout awaiting synchronization sequence ... потом наступает таймаут и прога закрывает соединение: Sep 11 14:04:38.00: [ 3949]: Bad HDLC terminating flag received. Sep 11 14:05:08.00: [ 3949]: Timeout awaiting synchronization sequence Sep 11 14:05:40.01: [ 3949]: MODEM <Empty line> Sep 11 14:05:42.01: [ 3949]: MODEM <Empty line> Sep 11 14:05:44.01: [ 3949]: MODEM <Empty line> Sep 11 14:05:44.01: [ 3949]: <-- [9:AT+FRH=3\r] Sep 11 14:06:29.54: [ 3949]: --> [0:] Sep 11 14:06:29.54: [ 3949]: MODEM <Empty line> Sep 11 14:06:29.54: [ 3949]: <-- data [1] Sep 11 14:06:29.74: [ 3949]: MODEM <Timeout> Sep 11 14:06:29.75: [ 3949]: RECV: 5376 bytes of data, 254 total lines Sep 11 14:06:29.75: [ 3949]: RECV keeping unconfirmed page Sep 11 14:06:29.75: [ 3949]: RECV FAX (000000071): from <UNSPECIFIED>, page 1 in 6:35, INF, 7.7 line/mm, 2-D MMR, 14400 bit/s Sep 11 14:06:29.75: [ 3949]: RECV FAX (000000071): recvq/fax000000069.tif from <UNSPECIFIED>, route to <unspecified>, 1 pages in 6:35 Sep 11 14:06:29.75: [ 3949]: RECV FAX: T.30 T2 timeout, expected signal not received Sep 11 14:06:29.75: [ 3949]: <-- [9:AT+FTH=3\r] Sep 11 14:06:37.31: [ 3949]: --> [0:] Sep 11 14:06:37.31: [ 3949]: RECV FAX (000000071): session with <UNSPECIFIED> terminated abnormally: T.30 T2 timeout, expected signal not received Sep 11 14:06:37.31: [ 3949]: RECV FAX: bin/faxrcvd "recvq/fax000000069.tif" "ttyS0" "000000071" "T.30 T2 timeout, expected signal not received" Sep 11 14:06:37.31: [ 3949]: RECV FAX: end Sep 11 14:06:37.31: [ 3949]: T.30 T2 timeout, expected signal not received Sep 11 14:06:37.31: [ 3949]: SESSION END но проблема в том что модем не кладёт трубку и держит её вплоть до полной перезгрузки сервака. Что делать?! Лазил по их сайту, но ничего не помогло или же я не понял идёю. Помогите кто может!!!!! Заранее спасибо!!! # # Generic Class 1 modem configuration. # # EDIT THIS CONFIGURATION TO REFLECT YOUR SETUP # CountryCode: 7 AreaCode: 495 FAXNumber: 0573 LongDistancePrefix: 1 InternationalPrefix: 011 DialStringRules: etc/dialrules ServerTracing: 1 SessionTracing: 11 RecvFileMode: 0644 LogFileMode: 0644 DeviceMode: 0644 RingsBeforeAnswer: 1 SpeakerVolume: off GettyArgs: "-h %l dx_%s" LocalIdentifier: "NothingSetup" TagLineFont: etc/lutRS18.pcf TagLineFormat: "From %%l|%c|Page %%P of %%T" MaxRecvPages: 25 # # # Modem-related stuff: should reflect modem command interface # and hardware connection/cabling (e.g. flow control). # ModemType: Class1 # use this to supply a hint ModemRate: 19200 # rate for DCE-DTE communication ModemFlowControl: xonxoff # XON/XOFF flow control assumed # ModemSetupDTRCmd: AT&D2 # setup so DTR drop resets modem ModemSetupDCDCmd: AT&C1 # setup so DCD follows carrier #GettyArgs: "-h %l dx_%s" # modem must auto-detect fax/data # # We can append the "@" symbol to the dial string so that # the modem will wait 5 seconds before attempting to connect # and return result codes that distinguish between no carrier # and no answer. This makes it possible to avoid problems with # repeatedly dialing a number that doesn't have a fax machine # (kudos to Stuart Lynne for this trick.) # # NB: If you need to prefix phone numbers to get through a PBX, # put it in the ModemDialCmd; e.g. "DT9%s@". # #ModemDialCmd: ATDT%s # T for tone dialing # # Other possible configuration stuff. The default strings are # shown below. Only those that are different from the defaults # need to be included in the configuration file. # ModemResetCmds: "AT&B1&N0&S0*F0S38.3=1S39=0" # stuff to do when modem is reset ModemAnswerCmd: ATA # use this to answer phone #ModemNoFlowCmd: AT&K # disable flow control cmd #ModemHardFlowCmd: AT&K3 # hardware flow control cmd #ModemSoftFlowCmd: AT&K4 # software flow control cmd #ModemNoAutoAnswerCmd: ATS0=0 # disable auto-answer # # Set modem speaker volume commands: OFF QUIET LOW MEDIUM HIGH. # Note that we both turn the speaker on/off and set volume. # ModemSetVolumeCmd: "ATM0 ATL0M1 ATL1M1 ATL2M1 ATL3M1" #ModemEchoOffCmd: ATE0 # disable command echo #ModemVerboseResultsCmd: ATV1 # enable verbose command results #ModemResultCodesCmd: ATQ0 # enable result codes #ModemOnHookCmd: ATH0 # place phone on hook (hangup) #ModemSoftResetCmd: ATZ # do soft reset of modem #ModemSoftResetCmdDelay: 3000 # pause after soft reset #ModemWaitTimeCmd: ATS7=60 # wait 60 seconds for carrier #ModemCommaPauseTimeCmd: ATS8=2 # comma pause time is 2 seconds #ModemRecvFillOrder: LSB2MSB # bit order of received facsimile #ModemSendFillOrder: LSB2MSB # bit order modem expects for transmit # Class1Cmd: AT+FCLASS=1 # command to enter class 1 Class1PPMWaitCmd: AT+FTS=7 # command to stop and wait before PPM Class1TCFWaitCmd: AT+FTS=7 # command to stop and wait before TCF Class1EOPWaitCmd: AT+FTS=9 # command to stop and wait before EOP Class1SwitchingCmd: AT+FRS=8 # silence between HDLC recv and trans Class1TrainingRecovery: 1500 # 1.5sec delay after training failure Class1RecvAbortOK: 200 # wait 200ms for abort response Class1RecvIdentTimer: 40000 # 35+5secs waiting for ident frames Class1TCFMaxNonZero: 10 # max 10% of data may be non-zero Class1TCFMinRun: 1000 # min run is 2/3rds of TCF duration Class1FrameOverhead: 2

Вы не можете добавлять комментарии в эту тему. Тема перемещена в архив.
Похожие темы
- Форум HylaFAX не кладет трубку (2012)
- Форум hylafax исходящий факс через перевод звонка (2009)
- Форум mgetty каждые 5 секунд переинициализирует модем (2003)
- Форум mgetty каждые 5 секунд переинициализирует модем (2003)
- Форум Немогу разобраться с mgetty, проблемма маленькая, а мозгов уже нехватает. (2003)
- Форум [беда] Фобос-Грунт (2011)
- Форум Люди умные, помогите ради христа, немогу понять что от меня хочет mgetty (2003)
- Форум [NVidia][история успеха] Ну что там говорил блоб качественный? (2011)
- Форум mgetty трубку не берет (2001)
- Форум не видит com порт (2007)