как програмно посмотреть марку ОЗУ, воткнутой в мамку?

пожалуйста =)

скотлы!!!!!!!

При начальной загрузке , гогда биос определяет винты и все такое, см. в нижней части экрана !

Сори невнимательно прочитал вопрос :(

может memtest86 поможет ???? http://www.memtest86.com/

Забавно, 5 ответов и ни одного близкого к правильному... Нет, это не автор исходного вопроса

>Забавно, 5 ответов и ни одного близкого к правильному... Нет, это не автор исходного вопроса

сам видать тоже не в курсе ? Да ? :)

1) ставим lm_sensors 2) modprobe eeprom 3) decode-dimms.pl

Вот пример содержимого EEPROM моего компа ;)

Decoding EEPROM /proc/sys/dev/sensors/eeprom-i2c-1-50 Guessing DIMM is in bank 1

---=== The Following is Required Data and is Applicable to all DIMM Types ===--- # of bytes written to SDRAM EEPROM 128 Total number of bytes in EEPROM 256 Fundemental Memory type ??? Number of Row Address Bits (SDRAM only) 13 Number of Col Address Bits (SDRAM only) 10 Number of Module Rows 1 Data Width (SDRAM only) 64 Module Interface Signal Levels SSTL 2.5 Cycle Time (SDRAM) highest CAS latency 7.5ns Access Time (SDRAM) 7.5ns Module Configuration Type No Parity Refresh Type Self Refreshing Refresh Rate Reduced (7.8uS) Primary SDRAM Component Bank Config No Bank2 OR Bank2 = Bank1 width Primary SDRAM Component Widths 8 Error Checking SDRAM Component Bank Config No Bank2 OR Bank2 = Bank1 width Error Checking SDRAM Component Widths Undefined! Min Clock Delay for Back to Back Random Access 1

---=== The Following Apply to SDRAM DIMMs ONLY ===--- Burst lengths supported Burst Length = 2 Burst Length = 4 Burst Length = 8

Number of Device Banks 4 Supported CAS Latencies CAS Latency = 3 CAS Latency = 4

Supported CS Latencies CS Latency = 0

Supported WE Latencies WE Latency = 1

SDRAM Module Attributes Differential Clock Input

SDRAM Device Attributes (General) Lower VCC Tolerance:10% Upper VCC Tolerance:10% Undefined (bit 6) Undefined (bit 7)

SDRAM Cycle Time (2nd highest CAS) 10nS SDRAM Access from Clock Time (2nd highest CAS) 7.5nS

---=== The Following are Optional (may be Bogus) ===--- SDRAM Cycle Time (3rd highest CAS) Undefined! SDRAM Access from Clock Time (3rd highest CAS) Undefined!

---=== The Following are Required (for SDRAMs) ===--- Minumum Row Precharge Time 80nS Row Active to Row Active Min 60nS RAS to CAS Delay 80nS Min RAS Pulse Width 45nS

---=== The Following are Required and Apply to ALL DIMMs ===--- Row Densities 256 MByte

---=== The Following are Proposed and Apply to SDRAM DIMMs ===--- Command and Address Signal Setup Time -1nS Command and Address Signal Hold Time -1nS Data Signal Setup Time 5nS Data Signal Hold Time 5nS SPD Revision code 0 EEPROM Checksum of bytes 0-62 0xE2 (verses calculated: 0xE2)

Manufacturer's JEDEC ID Code 0xAD00000000000000

Manufacturer's JEDEC ID Code ("╜") Manufacturing Location Code 0x56

Manufacurer's Part Number:" HYMD232 646A8R-H Revision Code 0x2020

Manufacturing Date 0x2032

Intel Specification for Frequency Undefined!

Intel Spec Details for 100MHz Support Junction Temp B (100 degrees C) Single Sided DIMM

Decoding EEPROM /proc/sys/dev/sensors/eeprom-i2c-1-51 Guessing DIMM is in bank 2

---=== The Following is Required Data and is Applicable to all DIMM Types ===--- # of bytes written to SDRAM EEPROM 128 Total number of bytes in EEPROM 256 Fundemental Memory type ??? Number of Row Address Bits (SDRAM only) 13 Number of Col Address Bits (SDRAM only) 10 Number of Module Rows 2 Data Width (SDRAM only) 64 Module Interface Signal Levels SSTL 2.5 Cycle Time (SDRAM) highest CAS latency 7.5ns Access Time (SDRAM) 7.5ns Module Configuration Type No Parity Refresh Type Self Refreshing Refresh Rate Reduced (7.8uS) Primary SDRAM Component Bank Config No Bank2 OR Bank2 = Bank1 width Primary SDRAM Component Widths 8 Error Checking SDRAM Component Bank Config No Bank2 OR Bank2 = Bank1 width Error Checking SDRAM Component Widths Undefined! Min Clock Delay for Back to Back Random Access 1

---=== The Following Apply to SDRAM DIMMs ONLY ===--- Burst lengths supported Burst Length = 2 Burst Length = 4 Burst Length = 8

Number of Device Banks 4 Supported CAS Latencies CAS Latency = 3 CAS Latency = 4

Supported CS Latencies CS Latency = 0

Supported WE Latencies WE Latency = 1

SDRAM Module Attributes Differential Clock Input

SDRAM Device Attributes (General) Lower VCC Tolerance:10% Upper VCC Tolerance:10%

SDRAM Cycle Time (2nd highest CAS) 10nS SDRAM Access from Clock Time (2nd highest CAS) 7.5nS

---=== The Following are Optional (may be Bogus) ===--- SDRAM Cycle Time (3rd highest CAS) Undefined! SDRAM Access from Clock Time (3rd highest CAS) Undefined!

---=== The Following are Required (for SDRAMs) ===--- Minumum Row Precharge Time 80nS Row Active to Row Active Min 60nS RAS to CAS Delay 80nS Min RAS Pulse Width 45nS

---=== The Following are Required and Apply to ALL DIMMs ===--- Row Densities 256 MByte

---=== The Following are Proposed and Apply to SDRAM DIMMs ===--- Command and Address Signal Setup Time -1nS Command and Address Signal Hold Time -1nS Data Signal Setup Time 5nS Data Signal Hold Time 5nS SPD Revision code 0 EEPROM Checksum of bytes 0-62 0x25 (verses calculated: 0x25)

Manufacturer's JEDEC ID Code 0x7F98000000000000

Manufacturer's JEDEC ID Code ("≤") Manufacturing Location Code 0x00

Manufacurer's Part Number:" KVR266X64C25/512 Revision Code 0x0000

Manufacturing Date 0x0001

Intel Specification for Frequency Undefined!

Intel Spec Details for 100MHz Support Junction Temp B (100 degrees C) Single Sided DIMM

Number of SDRAM DIMMs detected and decoded 2

sS, сам я в курсе. И 0x50-0x57 на i2c я знаю не хуже тебя. Только в последнее время я перестал помогать анонимным пользователям.

P.S. Это ты мне Option "Buttons" "3" простить не можешь :p

>P.S. Это ты мне Option "Buttons" "3" простить не можешь :p

Да не - мне пофиг тем более что эта опция игнорируется ;)

Нешто ты думаешь я задумываюсь над такими вещами как написание примеров настроек;) cat + grep + cut&paste на что придумано ;) а то что там могут быть несоответствия с документацией это пофиг- все же работает /:)

PS: я вот тоже думаю ... а стоит ли анонимусам помогать ;) man + гугл все равно луШШе помогают ;)