Почему в Х не работает переключение клавиатуры на русский после необходимой модификации XF86Config-4

0

0

Почему в Х не работает переключение клавиатуры на русский после необходимой модификации XF86Config-4. Загрузка Х происходит без сообщений о ошибках в XF86Config-4 но с сообщением "Couldn't load XKB keymap, ..." Подскажите в чём может быть дело и как ето исправить

Ссылка

←	Как получить список линков на странице, пригодный для wget -i ?

Терминалы и termcap

→

Цитату, сестра!
из лога - это раз, и из /etc/X11/XF86Config - это два.

~~Zulu~~ ★★☆☆
(29.10.03 16:31:58 MSK)

Ответ на: комментарий от Zulu 29.10.03 16:31:58 MSK

XF86Config:

Section "ServerLayout"
Identifier "XFree86 Configured"
Screen 0 "Screen0" 0 0
InputDevice "Keyboard0" "CoreKeyboard"
InputDevice "Mouse0" "CorePointer"
EndSection
Section "Files"
FontPath "tcp/10.1.42.97:7100"
EndSection

Section "Module"
Load "dbe"
Load "extmod"
Load "glx" # 3D layer
EndSection

Section "InputDevice"
Identifier "Keyboard0"
Driver "keyboard"

Option "AutoRepeat" "250 30"
Option "XkbRules" "xfree86"
# Option "XkbModel" "pc105"
Option "XkbModel" "pc101"
# Option "XkbLayout" "us,ua,ru"
Option "XkbLayout" "us,ua(winkeys),ru(winkeys)"
# Option "XkbVariant" "winkeys"
# Option "XkbOptions" "grp:ctrl_shift_toggle"
Option "XkbOptions" "grp:ctrl_shift_toggle,grp_led:scroll"
EndSection

### End of Multilanguage settings

Section "InputDevice"
Identifier "Mouse0"
Driver "mouse"
Option "Device" "/dev/ttyS0"
Option "Protocol" "Microsoft"
Option "BaudRate" "1200"
Option "Resolution" "50"
Option "Emulate3Buttons" "off"
Option "ZAxisMapping" "4 5"
Option "Buttons" "3"
EndSection

Section "Monitor"
Identifier "My Monitor"
VendorName "Unknown"
ModelName "Unknown"
HorizSync 31-62
VertRefresh 50-70
EndSection

Section "Device"
Identifier "My Video Card"
Driver "s3virge"

# Option "NoAccel"
EndSection

Section "Screen"
Identifier "Screen0"
Device "My Video Card"
Monitor "My Monitor"
DefaultDepth 16
Subsection "Display"
Depth 16
Modes "800x600"
EndSubSection
EndSection

Section "DRI"

EndSection
=============================================
XFree86.0.log:

This is a pre-release version of XFree86, and is not supported in any
way. Bugs may be reported to XFree86@XFree86.Org and patches submitted
to fixes@XFree86.Org. Before reporting bugs in pre-release versions,
please check the latest version in the XFree86 CVS repository
(http://www.XFree86.Org/cvs)

XFree86 Version 4.2.99.1 / X Window System
(protocol Version 11, revision 0, vendor release 6600)
Release Date: 15 October 2002
If the server is older than 6-12 months, or if your card is
newer than the above date, look for a newer version before
reporting problems. (See http://www.XFree86.Org/)
Build Operating System: Linux 2.4.7-crypto6 i686 [ELF]
Module Loader present
Markers: (--) probed, (**) from config file, (==) default setting,
(++) from command line, (!!) notice, (II) informational,
(WW) warning, (EE) error, (NI) not implemented, (??) unknown.
(==) Log file: "/var/log/XFree86.0.log", Time: Wed Oct 29 15:18:58 2003
(==) Using config file: "/etc/XF86Config"
(==) ServerLayout "XFree86 Configured"
(**) |-->Screen "Screen0" (0)
(**) | |-->Monitor "My Monitor"
(**) | |-->Device "My Video Card"
(**) |-->Input Device "Keyboard0"
(**) Option "AutoRepeat" "250 30"
(**) Option "XkbRules" "xfree86"
(**) XKB: rules: "xfree86"
(**) Option "XkbModel" "pc101"
(**) XKB: model: "pc101"
(**) Option "XkbLayout" "us,ua(winkeys),ru(winkeys)"
(**) XKB: layout: "us,ua(winkeys),ru(winkeys)"
(**) Option "XkbOptions" "grp:ctrl_shift_toggle,grp_led:scroll"
(**) XKB: options: "grp:ctrl_shift_toggle,grp_led:scroll"
(==) Keyboard: CustomKeycode disabled
(**) |-->Input Device "Mouse0"
(**) FontPath set to "tcp/10.1.42.97:7100"
(==) RgbPath set to "/usr/X11R6/lib/X11/rgb"
(==) ModulePath set to "/usr/X11R6/lib/modules"
(--) using VT number 3

(WW) Open APM failed (/dev/apm_bios) (No such file or directory)
(II) Module ABI versions:
XFree86 ANSI C Emulation: 0.1
XFree86 Video Driver: 0.6
XFree86 XInput driver : 0.3
XFree86 Server Extension : 0.1
XFree86 Font Renderer : 0.3
(II) Loader running on linux
(II) LoadModule: "bitmap"
(II) Loading /usr/X11R6/lib/modules/fonts/libbitmap.a
(II) Module bitmap: vendor="The XFree86 Project"
compiled for 4.2.99.1, module version = 1.0.0
Module class: XFree86 Font Renderer
ABI class: XFree86 Font Renderer, version 0.3
(II) Loading font Bitmap
(II) LoadModule: "pcidata"
(II) Loading /usr/X11R6/lib/modules/libpcidata.a
(II) Module pcidata: vendor="The XFree86 Project"
compiled for 4.2.99.1, module version = 1.0.0
ABI class: XFree86 Video Driver, version 0.6
(II) PCI: Probing config type using method 1
(II) PCI: Config type is 1
(II) PCI: stages = 0x03, oldVal1 = 0x8000980c, mode1Res1 = 0x80000000
(II) PCI: PCI scan (all values are in hex)
(II) PCI: 00:00:0: chip 8086,7030 card 0000,0000 rev 02 class 06,00,00 hdr 00
(II) PCI: 00:07:0: chip 8086,7000 card 0000,0000 rev 01 class 06,01,00 hdr 80
(II) PCI: 00:07:1: chip 8086,7010 card 0000,0000 rev 00 class 01,01,80 hdr 00
(II) PCI: 00:11:0: chip 10b7,9055 card 10b7,9055 rev 64 class 02,00,00 hdr 00
(II) PCI: 00:12:0: chip 5333,8a01 card 5333,8a01 rev 01 class 03,00,00 hdr 00
(II) PCI: 00:13:0: chip 10b7,9055 card 10b7,9055 rev 30 class 02,00,00 hdr 00
(II) PCI: End of PCI scan
(II) Host-to-PCI bridge:
(II) Bus 0: bridge is at (0:0:0), (0,0,0), BCTRL: 0x0008 (VGA_EN is set)
(II) Bus 0 I/O range:
[0] -1 0 0x00000000 - 0x0000ffff (0x10000) IX[B]
(II) Bus 0 non-prefetchable memory range:
[0] -1 0 0x00000000 - 0xffffffff (0x0) MX[B]
(II) Bus 0 prefetchable memory range:
[0] -1 0 0x00000000 - 0xffffffff (0x0) MX[B]
(II) PCI-to-ISA bridge:
(II) Bus -1: bridge is at (0:7:0), (0,-1,-1), BCTRL: 0x0008 (VGA_EN is set)
(--) PCI:*(0:18:0) S3 Inc. ViRGE/DX or /GX rev 1, Mem @ 0xe0000000/26
(II) Addressable bus resource ranges are
[0] -1 0 0x00000000 - 0xffffffff (0x0) MX[B]
[1] -1 0 0x00000000 - 0x0000ffff (0x10000) IX[B]
(II) OS-reported resource ranges:
[0] -1 0 0xffe00000 - 0xffffffff (0x200000) MX[B](B)
[1] -1 0 0x00100000 - 0x3fffffff (0x3ff00000) MX[B]E(B)
[2] -1 0 0x000f0000 - 0x000fffff (0x10000) MX[B]
[3] -1 0 0x000c0000 - 0x000effff (0x30000) MX[B]
[4] -1 0 0x00000000 - 0x0009ffff (0xa0000) MX[B]
[5] -1 0 0x0000ffff - 0x0000ffff (0x1) IX[B]
[6] -1 0 0x00000000 - 0x000000ff (0x100) IX[B]
(II) Active PCI resource ranges:
[0] -1 0 0xe4001000 - 0xe400107f (0x80) MX[B]
[1] -1 0 0xe4000000 - 0xe400007f (0x80) MX[B]
[2] -1 0 0xe0000000 - 0xe3ffffff (0x4000000) MX[B](B)
[3] -1 0 0x00006200 - 0x0000627f (0x80) IX[B]
[4] -1 0 0x00006100 - 0x0000617f (0x80) IX[B]
[5] -1 0 0x0000f000 - 0x0000f00f (0x10) IX[B]
(II) Active PCI resource ranges after removing overlaps:
[0] -1 0 0xe4001000 - 0xe400107f (0x80) MX[B]
[1] -1 0 0xe4000000 - 0xe400007f (0x80) MX[B]
[2] -1 0 0xe0000000 - 0xe3ffffff (0x4000000) MX[B](B)
[3] -1 0 0x00006200 - 0x0000627f (0x80) IX[B]
[4] -1 0 0x00006100 - 0x0000617f (0x80) IX[B]
[5] -1 0 0x0000f000 - 0x0000f00f (0x10) IX[B]
(II) OS-reported resource ranges after removing overlaps with PCI:
[0] -1 0 0xffe00000 - 0xffffffff (0x200000) MX[B](B)
[1] -1 0 0x00100000 - 0x3fffffff (0x3ff00000) MX[B]E(B)
[2] -1 0 0x000f0000 - 0x000fffff (0x10000) MX[B]
[3] -1 0 0x000c0000 - 0x000effff (0x30000) MX[B]
[4] -1 0 0x00000000 - 0x0009ffff (0xa0000) MX[B]
[5] -1 0 0x0000ffff - 0x0000ffff (0x1) IX[B]
[6] -1 0 0x00000000 - 0x000000ff (0x100) IX[B]
(II) All system resource ranges:
[0] -1 0 0xffe00000 - 0xffffffff (0x200000) MX[B](B)
[1] -1 0 0x00100000 - 0x3fffffff (0x3ff00000) MX[B]E(B)
[2] -1 0 0x000f0000 - 0x000fffff (0x10000) MX[B]
[3] -1 0 0x000c0000 - 0x000effff (0x30000) MX[B]
[4] -1 0 0x00000000 - 0x0009ffff (0xa0000) MX[B]
[5] -1 0 0xe4001000 - 0xe400107f (0x80) MX[B]
[6] -1 0 0xe4000000 - 0xe400007f (0x80) MX[B]
[7] -1 0 0xe0000000 - 0xe3ffffff (0x4000000) MX[B](B)
[8] -1 0 0x0000ffff - 0x0000ffff (0x1) IX[B]
[9] -1 0 0x00000000 - 0x000000ff (0x100) IX[B]
[10] -1 0 0x00006200 - 0x0000627f (0x80) IX[B]
[11] -1 0 0x00006100 - 0x0000617f (0x80) IX[B]
[12] -1 0 0x0000f000 - 0x0000f00f (0x10) IX[B]
(II) LoadModule: "dbe"
(II) Loading /usr/X11R6/lib/modules/extensions/libdbe.a
(II) Module dbe: vendor="The XFree86 Project"
compiled for 4.2.99.1, module version = 1.0.0
Module class: XFree86 Server Extension
ABI class: XFree86 Server Extension, version 0.1
(II) Loading extension DOUBLE-BUFFER
(II) LoadModule: "extmod"
(II) Loading /usr/X11R6/lib/modules/extensions/libextmod.a
(II) Module extmod: vendor="The XFree86 Project"
compiled for 4.2.99.1, module version = 1.0.0
Module class: XFree86 Server Extension
ABI class: XFree86 Server Extension, version 0.1
(II) Loading extension SHAPE
(II) Loading extension MIT-SUNDRY-NONSTANDARD
(II) Loading extension BIG-REQUESTS
(II) Loading extension SYNC
(II) Loading extension MIT-SCREEN-SAVER
(II) Loading extension XC-MISC
(II) Loading extension XFree86-VidModeExtension
(II) Loading extension XFree86-Misc
(II) Loading extension XFree86-DGA
(II) Loading extension DPMS
(II) Loading extension FontCache
(II) Loading extension TOG-CUP
(II) Loading extension Extended-Visual-Information
(II) Loading extension XVideo
(II) Loading extension XVideo-MotionCompensation
(II) Loading extension X-Resource
(II) LoadModule: "glx"
(II) Loading /usr/X11R6/lib/modules/extensions/libglx.a
(II) Module glx: vendor="The XFree86 Project"
compiled for 4.2.99.1, module version = 1.0.0
ABI class: XFree86 Server Extension, version 0.1
(II) Loading sub module "GLcore"
(II) LoadModule: "GLcore"
(II) Loading /usr/X11R6/lib/modules/extensions/libGLcore.a
(II) Module GLcore: vendor="The XFree86 Project"
compiled for 4.2.99.1, module version = 1.0.0
ABI class: XFree86 Server Extension, version 0.1
(II) Loading extension GLX
(II) LoadModule: "s3virge"
(II) Loading /usr/X11R6/lib/modules/drivers/s3virge_drv.o
(II) Module s3virge: vendor="The XFree86 Project"
compiled for 4.2.99.1, module version = 1.8.3
Module class: XFree86 Video Driver
ABI class: XFree86 Video Driver, version 0.6
(II) LoadModule: "mouse"
(II) Loading /usr/X11R6/lib/modules/input/mouse_drv.o
(II) Module mouse: vendor="The XFree86 Project"
compiled for 4.2.99.1, module version = 1.0.0
Module class: XFree86 XInput Driver
ABI class: XFree86 XInput driver, version 0.3
(II) S3VIRGE: driver (version 1.8.3) for S3 ViRGE chipsets: virge, 86C325,
virge vx, 86C988, virge dx, virge gx, 86C375, 86C385, virge gx2,
86C357, virge mx, 86C260, virge mx+, 86C280, trio 3d, 86C365,
trio 3d/2x, 86C362, 86C368
(II) Primary Device is: PCI 00:12:0
(--) Assigning device section with no busID to primary device
(--) Chipset virge dx found
(II) resource ranges after xf86ClaimFixedResources() call:
[0] -1 0 0xffe00000 - 0xffffffff (0x200000) MX[B](B)
[1] -1 0 0x00100000 - 0x3fffffff (0x3ff00000) MX[B]E(B)
[2] -1 0 0x000f0000 - 0x000fffff (0x10000) MX[B]
[3] -1 0 0x000c0000 - 0x000effff (0x30000) MX[B]
[4] -1 0 0x00000000 - 0x0009ffff (0xa0000) MX[B]
[5] -1 0 0xe4001000 - 0xe400107f (0x80) MX[B]
[6] -1 0 0xe4000000 - 0xe400007f (0x80) MX[B]
[7] -1 0 0xe0000000 - 0xe3ffffff (0x4000000) MX[B](B)
[8] -1 0 0x0000ffff - 0x0000ffff (0x1) IX[B]
[9] -1 0 0x00000000 - 0x000000ff (0x100) IX[B]
[10] -1 0 0x00006200 - 0x0000627f (0x80) IX[B]
[11] -1 0 0x00006100 - 0x0000617f (0x80) IX[B]
[12] -1 0 0x0000f000 - 0x0000f00f (0x10) IX[B]
(II) resource ranges after probing:
[0] -1 0 0xffe00000 - 0xffffffff (0x200000) MX[B](B)
[1] -1 0 0x00100000 - 0x3fffffff (0x3ff00000) MX[B]E(B)
[2] -1 0 0x000f0000 - 0x000fffff (0x10000) MX[B]
[3] -1 0 0x000c0000 - 0x000effff (0x30000) MX[B]
[4] -1 0 0x00000000 - 0x0009ffff (0xa0000) MX[B]
[5] -1 0 0xe4001000 - 0xe400107f (0x80) MX[B]
[6] -1 0 0xe4000000 - 0xe400007f (0x80) MX[B]
[7] -1 0 0xe0000000 - 0xe3ffffff (0x4000000) MX[B](B)
[8] 0 0 0x000a0000 - 0x000affff (0x10000) MS[B]
[9] 0 0 0x000b0000 - 0x000b7fff (0x8000) MS[B]
[10] 0 0 0x000b8000 - 0x000bffff (0x8000) MS[B]
[11] -1 0 0x0000ffff - 0x0000ffff (0x1) IX[B]
[12] -1 0 0x00000000 - 0x000000ff (0x100) IX[B]
[13] -1 0 0x00006200 - 0x0000627f (0x80) IX[B]
[14] -1 0 0x00006100 - 0x0000617f (0x80) IX[B]
[15] -1 0 0x0000f000 - 0x0000f00f (0x10) IX[B]
[16] 0 0 0x000003b0 - 0x000003bb (0xc) IS[B]
[17] 0 0 0x000003c0 - 0x000003df (0x20) IS[B]
(II) Setting vga for screen 0.
(II) Loading sub module "vgahw"
(II) LoadModule: "vgahw"
(II) Loading /usr/X11R6/lib/modules/libvgahw.a
(II) Module vgahw: vendor="The XFree86 Project"
compiled for 4.2.99.1, module version = 0.1.0
ABI class: XFree86 Video Driver, version 0.6
(**) S3VIRGE(0): Depth 16, (--) framebuffer bpp 16
(==) S3VIRGE(0): RGB weight 565
(==) S3VIRGE(0): Default visual is TrueColor
(==) S3VIRGE(0): Using HW Cursor
(==) S3VIRGE(0): Using fb.
(==) S3VIRGE(0): mx_cr3a_fix.
(==) S3VIRGE(0): XVideo allowed (depends on chipset).
(II) Loading sub module "vbe"
(II) LoadModule: "vbe"
(II) Loading /usr/X11R6/lib/modules/libvbe.a
(II) Module vbe: vendor="The XFree86 Project"
compiled for 4.2.99.1, module version = 1.1.0
ABI class: XFree86 Video Driver, version 0.6
(II) Loading sub module "int10"
(II) LoadModule: "int10"
(II) Loading /usr/X11R6/lib/modules/linux/libint10.a
(II) Module int10: vendor="The XFree86 Project"
compiled for 4.2.99.1, module version = 1.0.0
ABI class: XFree86 Video Driver, version 0.6
(II) S3VIRGE(0): initializing int10
(II) S3VIRGE(0): Primary V_BIOS segment is: 0xc000
(WW) System lacks support for changing MTRRs
(II) S3VIRGE(0): VESA BIOS detected
(II) S3VIRGE(0): VESA VBE Version 1.2
(II) S3VIRGE(0): VESA VBE Total Mem: 4096 kB
(II) S3VIRGE(0): VESA VBE OEM: S3 Incorporated. 86C375/86C385
(--) S3VIRGE(0): Chipset: "virge dx"
(II) S3VIRGE(0): vgaHWGetIOBase: hwp->IOBase is 0x03d0, hwp->PIOOffset is 0x0000
(II) S3VIRGE(0): vgaHWGetIOBase: hwp->IOBase is 0x03d0, hwp->PIOOffset is 0x0000
(II) Loading sub module "ddc"
(II) LoadModule: "ddc"
(II) Loading /usr/X11R6/lib/modules/libddc.a
(II) Module ddc: vendor="The XFree86 Project"
compiled for 4.2.99.1, module version = 1.0.0
ABI class: XFree86 Video Driver, version 0.6
(--) S3VIRGE(0): No DDC signal
(II) Loading sub module "i2c"
(II) LoadModule: "i2c"
(II) Loading /usr/X11R6/lib/modules/libi2c.a
(II) Module i2c: vendor="The XFree86 Project"
compiled for 4.2.99.1, module version = 1.2.0
ABI class: XFree86 Video Driver, version 0.6
(II) S3VIRGE(0): I2C bus "I2C bus" initialized.
(II) S3VIRGE(0): I2C device "I2C bus:ddc2" registered at address 0xA0.
(II) S3VIRGE(0): I2C device "I2C bus:ddc2" removed.
(==) S3VIRGE(0): Using gamma correction (1.0, 1.0, 1.0)
(--) S3VIRGE(0): videoram: 4096k
(--) S3VIRGE(0): Detected current MCLK value of 69.801 MHz
(II) S3VIRGE(0): My Monitor: Using hsync range of 31.00-62.00 kHz
(II) S3VIRGE(0): My Monitor: Using vrefresh range of 50.00-70.00 Hz
(II) S3VIRGE(0): Clock range: 20.00 to 270.00 MHz
(II) S3VIRGE(0): Not using default mode "640x350" (vrefresh out of range)
(II) S3VIRGE(0): Not using default mode "320x175" (bad mode clock/interlace/doublescan)
(II) S3VIRGE(0): Not using default mode "640x400" (vrefresh out of range)
(II) S3VIRGE(0): Not using default mode "320x200" (bad mode clock/interlace/doublescan)
(II) S3VIRGE(0): Not using default mode "720x400" (vrefresh out of range)
(II) S3VIRGE(0): Not using default mode "360x200" (bad mode clock/interlace/doublescan)
(II) S3VIRGE(0): Not using default mode "320x240" (bad mode clock/interlace/doublescan)
(II) S3VIRGE(0): Not using default mode "640x480" (vrefresh out of range)
(II) S3VIRGE(0): Not using default mode "320x240" (bad mode clock/interlace/doublescan)
(II) S3VIRGE(0): Not using default mode "640x480" (vrefresh out of range)
(II) S3VIRGE(0): Not using default mode "320x240" (bad mode clock/interlace/doublescan)
(II) S3VIRGE(0): Not using default mode "640x480" (vrefresh out of range)
(II) S3VIRGE(0): Not using default mode "320x240" (bad mode clock/interlace/doublescan)
(II) S3VIRGE(0): Not using default mode "400x300" (bad mode clock/interlace/doublescan)
(II) S3VIRGE(0): Not using default mode "400x300" (bad mode clock/interlace/doublescan)
(II) S3VIRGE(0): Not using default mode "800x600" (vrefresh out of range)
(II) S3VIRGE(0): Not using default mode "400x300" (bad mode clock/interlace/doublescan)
(II) S3VIRGE(0): Not using default mode "800x600" (vrefresh out of range)
(II) S3VIRGE(0): Not using default mode "400x300" (bad mode clock/interlace/doublescan)
(II) S3VIRGE(0): Not using default mode "800x600" (vrefresh out of range)
(II) S3VIRGE(0): Not using default mode "400x300" (bad mode clock/interlace/doublescan)
(II) S3VIRGE(0): Not using default mode "1024x768" (vrefresh out of range)
(II) S3VIRGE(0): Not using default mode "512x384" (bad mode clock/interlace/doublescan)
(II) S3VIRGE(0): Not using default mode "512x384" (bad mode clock/interlace/doublescan)
(II) S3VIRGE(0): Not using default mode "512x384" (bad mode clock/interlace/doublescan)
(II) S3VIRGE(0): Not using default mode "1024x768" (vrefresh out of range)
(II) S3VIRGE(0): Not using default mode "512x384" (bad mode clock/interlace/doublescan)
(II) S3VIRGE(0): Not using default mode "1024x768" (hsync out of range)
(II) S3VIRGE(0): Not using default mode "512x384" (bad mode clock/interlace/doublescan)
(II) S3VIRGE(0): Not using default mode "1152x864" (hsync out of range)
(II) S3VIRGE(0): Not using default mode "576x432" (bad mode clock/interlace/doublescan)
(II) S3VIRGE(0): Not using default mode "640x480" (bad mode clock/interlace/doublescan)
(II) S3VIRGE(0): Not using default mode "1280x960" (hsync out of range)
(II) S3VIRGE(0): Not using default mode "640x480" (bad mode clock/interlace/doublescan)
(II) S3VIRGE(0): Not using default mode "1280x1024" (hsync out of range)
(II) S3VIRGE(0): Not using default mode "640x512" (bad mode clock/interlace/doublescan)
(II) S3VIRGE(0): Not using default mode "1280x1024" (hsync out of range)
(II) S3VIRGE(0): Not using default mode "640x512" (bad mode clock/interlace/doublescan)
(II) S3VIRGE(0): Not using default mode "1280x1024" (hsync out of range)
(II) S3VIRGE(0): Not using default mode "640x512" (bad mode clock/interlace/doublescan)
(II) S3VIRGE(0): Not using default mode "1600x1200" (horizontal timing out of range)
(II) S3VIRGE(0): Not using default mode "800x600" (bad mode clock/interlace/doublescan)
(II) S3VIRGE(0): Not using default mode "1600x1200" (horizontal timing out of range)
(II) S3VIRGE(0): Not using default mode "800x600" (bad mode clock/interlace/doublescan)
(II) S3VIRGE(0): Not using default mode "1600x1200" (horizontal timing out of range)
(II) S3VIRGE(0): Not using default mode "800x600" (bad mode clock/interlace/doublescan)
(II) S3VIRGE(0): Not using default mode "1600x1200" (horizontal timing out of range)
(II) S3VIRGE(0): Not using default mode "800x600" (bad mode clock/interlace/doublescan)
(II) S3VIRGE(0): Not using default mode "1600x1200" (horizontal timing out of range)
(II) S3VIRGE(0): Not using default mode "800x600" (bad mode clock/interlace/doublescan)
(II) S3VIRGE(0): Not using default mode "1792x1344" (insufficient memory for mode)
(II) S3VIRGE(0): Not using default mode "896x672" (bad mode clock/interlace/doublescan)
(II) S3VIRGE(0): Not using default mode "1792x1344" (insufficient memory for mode)
(II) S3VIRGE(0): Not using default mode "896x672" (bad mode clock/interlace/doublescan)
(II) S3VIRGE(0): Not using default mode "1856x1392" (insufficient memory for mode)
(II) S3VIRGE(0): Not using default mode "928x696" (bad mode clock/interlace/doublescan)
(II) S3VIRGE(0): Not using default mode "1856x1392" (insufficient memory for mode)
(II) S3VIRGE(0): Not using default mode "928x696" (bad mode clock/interlace/doublescan)
(II) S3VIRGE(0): Not using default mode "1920x1440" (insufficient memory for mode)
(II) S3VIRGE(0): Not using default mode "960x720" (bad mode clock/interlace/doublescan)
(II) S3VIRGE(0): Not using default mode "1920x1440" (insufficient memory for mode)
(II) S3VIRGE(0): Not using default mode "960x720" (bad mode clock/interlace/doublescan)
(II) S3VIRGE(0): Not using default mode "832x624" (vrefresh out of range)
(II) S3VIRGE(0): Not using default mode "416x312" (bad mode clock/interlace/doublescan)
(II) S3VIRGE(0): Not using default mode "576x384" (bad mode clock/interlace/doublescan)
(II) S3VIRGE(0): Not using default mode "1400x1050" (hsync out of range)
(II) S3VIRGE(0): Not using default mode "700x525" (bad mode clock/interlace/doublescan)
(II) S3VIRGE(0): Not using default mode "1400x1050" (hsync out of range)
(II) S3VIRGE(0): Not using default mode "700x525" (bad mode clock/interlace/doublescan)
(II) S3VIRGE(0): Not using default mode "1600x1024" (hsync out of range)
(II) S3VIRGE(0): Not using default mode "800x512" (bad mode clock/interlace/doublescan)
(--) S3VIRGE(0): Virtual size is 1280x960 (pitch 1280)
(**) S3VIRGE(0): Default mode "800x600": 40.0 MHz, 37.9 kHz, 60.3 Hz
(II) S3VIRGE(0): Modeline "800x600" 40.00 800 840 968 1056 600 601 605 628 +hsync +vsync
(**) S3VIRGE(0): Default mode "1280x960": 108.0 MHz, 60.0 kHz, 60.0 Hz
(II) S3VIRGE(0): Modeline "1280x960" 108.00 1280 1376 1488 1800 960 961 964 1000 +hsync +vsync
(**) S3VIRGE(0): Default mode "1152x768": 65.0 MHz, 44.2 kHz, 54.8 Hz
(II) S3VIRGE(0): Modeline "1152x768" 65.00 1152 1178 1314 1472 768 771 777 806 +hsync +vsync
(**) S3VIRGE(0): Default mode "1024x768": 75.0 MHz, 56.5 kHz, 70.1 Hz
(II) S3VIRGE(0): Modeline "1024x768" 75.00 1024 1048 1184 1328 768 771 777 806 -hsync -vsync
(**) S3VIRGE(0): Default mode "1024x768": 65.0 MHz, 48.4 kHz, 60.0 Hz
(II) S3VIRGE(0): Modeline "1024x768" 65.00 1024 1048 1184 1344 768 771 777 806 -hsync -vsync
(**) S3VIRGE(0): Default mode "800x600": 36.0 MHz, 35.2 kHz, 56.2 Hz
(II) S3VIRGE(0): Modeline "800x600" 36.00 800 824 896 1024 600 601 603 625 +hsync +vsync
(**) S3VIRGE(0): Default mode "640x480": 25.2 MHz, 31.5 kHz, 60.0 Hz
(II) S3VIRGE(0): Modeline "640x480" 25.20 640 656 752 800 480 490 492 525 -hsync -vsync
(==) S3VIRGE(0): DPI set to (75, 75)
(II) Loading sub module "fb"
(II) LoadModule: "fb"
(II) Loading /usr/X11R6/lib/modules/libfb.a
(II) Module fb: vendor="The XFree86 Project"
compiled for 4.2.99.1, module version = 1.0.0
ABI class: XFree86 ANSI C Emulation, version 0.1
(II) Loading sub module "xaa"
(II) LoadModule: "xaa"
(II) Loading /usr/X11R6/lib/modules/libxaa.a
(II) Module xaa: vendor="The XFree86 Project"
compiled for 4.2.99.1, module version = 1.0.0
ABI class: XFree86 Video Driver, version 0.6
(II) Loading sub module "ramdac"
(II) LoadModule: "ramdac"
(II) Loading /usr/X11R6/lib/modules/libramdac.a
(II) Module ramdac: vendor="The XFree86 Project"
compiled for 4.2.99.1, module version = 0.1.0
ABI class: XFree86 Video Driver, version 0.6
(II) do I need RAC? No, I don't.
(II) resource ranges after preInit:
[0] 0 0 0xe0000000 - 0xe3ffffff (0x4000000) MS[B]
[1] -1 0 0xffe00000 - 0xffffffff (0x200000) MX[B](B)
[2] -1 0 0x00100000 - 0x3fffffff (0x3ff00000) MX[B]E(B)
[3] -1 0 0x000f0000 - 0x000fffff (0x10000) MX[B]
[4] -1 0 0x000c0000 - 0x000effff (0x30000) MX[B]
[5] -1 0 0x00000000 - 0x0009ffff (0xa0000) MX[B]
[6] -1 0 0xe4001000 - 0xe400107f (0x80) MX[B]
[7] -1 0 0xe4000000 - 0xe400007f (0x80) MX[B]
[8] -1 0 0xe0000000 - 0xe3ffffff (0x4000000) MX[B](B)
[9] 0 0 0x000a0000 - 0x000affff (0x10000) MS[B](OprD)
[10] 0 0 0x000b0000 - 0x000b7fff (0x8000) MS[B](OprD)
[11] 0 0 0x000b8000 - 0x000bffff (0x8000) MS[B](OprD)
[12] -1 0 0x0000ffff - 0x0000ffff (0x1) IX[B]
[13] -1 0 0x00000000 - 0x000000ff (0x100) IX[B]
[14] -1 0 0x00006200 - 0x0000627f (0x80) IX[B]
[15] -1 0 0x00006100 - 0x0000617f (0x80) IX[B]
[16] -1 0 0x0000f000 - 0x0000f00f (0x10) IX[B]
[17] 0 0 0x000003b0 - 0x000003bb (0xc) IS[B](OprU)
[18] 0 0 0x000003c0 - 0x000003df (0x20) IS[B](OprU)
(II) S3VIRGE(0): vgaHWGetIOBase: hwp->IOBase is 0x03d0, hwp->PIOOffset is 0x0000
(II) S3VIRGE(0): vgaHWGetIOBase: hwp->IOBase is 0x03d0, hwp->PIOOffset is 0x0000
(**) S3VIRGE(0): Using FB
(II) S3VIRGE(0): Using XFree86 Acceleration Architecture (XAA)
Screen to screen bit blits
Solid filled rectangles
8x8 mono pattern filled rectangles
CPU to Screen color expansion
Solid Horizontal and Vertical Lines
Image Writes
Offscreen Pixmaps
Setting up tile and stipple cache:
26 128x128 slots
6 256x256 slots
(==) S3VIRGE(0): Backing store disabled
(==) S3VIRGE(0): Silken mouse enabled
(II) S3VIRGE(0): Using overlay video
(II) Initializing built-in extension MIT-SHM
(II) Initializing built-in extension XInputExtension
(II) Initializing built-in extension XTEST
(II) Initializing built-in extension XKEYBOARD
(II) Initializing built-in extension LBX
(II) Initializing built-in extension XC-APPGROUP
(II) Initializing built-in extension SECURITY
(II) Initializing built-in extension XINERAMA
(II) Initializing built-in extension XFree86-Bigfont
(II) Initializing built-in extension RENDER
(II) Initializing built-in extension RANDR
(II) Keyboard "Keyboard0" handled by legacy driver
(**) Option "Protocol" "Microsoft"
(**) Mouse0: Protocol: "Microsoft"
(**) Option "CorePointer"
(**) Mouse0: Core Pointer
(**) Option "Device" "/dev/ttyS0"
(**) Option "BaudRate" "1200"
(**) Option "StopBits" "1"
(**) Option "DataBits" "7"
(**) Option "Parity" "None"
(**) Option "Vmin" "1"
(**) Option "Vtime" "0"
(**) Option "FlowControl" "None"
(**) Option "Buttons" "3"
(**) Option "Emulate3Buttons" "off"
(**) Option "ZAxisMapping" "4 5"
(**) Mouse0: ZAxisMapping: buttons 4 and 5
(**) Mouse0: Buttons: 5
(**) Option "Resolution" "50"
(**) Mouse0: Resolution: 50
(**) Mouse0: BaudRate: 1200
(II) XINPUT: Adding extended input device "Mouse0" (type: MOUSE)
Couldn't load XKB keymap, falling back to pre-XKB keymap
s3v: warning: VerticalRetraceWait timed out(2:3).
s3v: warning: VerticalRetraceWait timed out(2:3).

anonymous
(29.10.03 17:00:54 MSK)

Ответ на: комментарий от anonymous 29.10.03 17:00:54 MSK

Couldn't load XKB keymap, falling back to pre-XKB keymap

grustnoe ★★
(29.10.03 18:55:10 MSK)

Ответ на: комментарий от grustnoe 29.10.03 18:55:10 MSK

    Option              "XkbRules"              "xfree86"
    Option              "XkbModel"              "pc101"
    Option              "XkbLayout"             "us,ru"
    Option              "XkbOptions"            "grp:ctrl_shift_toggle,grp_led:scroll"

theserg ★★★
(30.10.03 00:23:54 MSK)

Ответ на: комментарий от theserg 30.10.03 00:23:54 MSK

А он прав , стервец :) ... пиздец , я пока одуплюсь на что-то ответить , тут до меня брага весёлых парней всех излечит и исцелит :)

SpaD ☆
(30.10.03 02:28:25 MSK)

Ссылка

Ответ на: комментарий от theserg 30.10.03 00:23:54 MSK

Mодифицировал XF86Config согласно приведённого выше примера но русский всёравно не работает.

anonymous
(30.10.03 14:15:08 MSK)

Ссылка

Ответ на: комментарий от grustnoe 29.10.03 18:55:10 MSK

Подскажите как с этим боротся

anonymous
(30.10.03 14:16:02 MSK)

Ответ на: комментарий от anonymous 30.10.03 14:16:02 MSK

Указывать раскладки через запятую можно в X 4.3 - и то, не в каждом порядке оно работает.
В 4.2 надо 
Section "InputDevice"
        Identifier  "Generic Keyboard"
        Driver      "keyboard"
        Option      "CoreKeyboard"
        Option      "XkbRules" "xfree86"
        Option      "XkbModel" "pc105"
        Option      "XkbLayout" "ru"
        Option      "XkbVariant" "winkeys"
        Option      "XkbOptions" "grp:ctrl_shift_toggle,grp_led:scroll"
EndSection

~~Zulu~~ ★★☆☆
(30.10.03 18:18:24 MSK)

Ответ на: комментарий от Zulu 30.10.03 18:18:24 MSK

Спасибо! С двумя раскладками разобрался. Но как в Х 4.2 сделать поддержку 3 раскладок (русский, украинский и английский)????

anonymous
(30.10.03 19:05:59 MSK)

Ссылка

Вы не можете добавлять комментарии в эту тему. Тема перемещена в архив.

←	Как получить список линков на странице, пригодный для wget -i ?

General

Терминалы и termcap

→

Похожие темы