I/O error hda

0

0

Друг пришёл с системным блоком, говорит, что не установить винду. Включил resquelivecd и сразу же бросились в глаза сообщения о том, что не подобраться к hda. Снял пробы :)

MBR не обнулить (/dev/zero) из-за IO error, in проходит, а out нет

Далее...
$ fdisk /dev/hda

Unable to open /dev/hda

root@ttyp0[knoppix]# fsck.vfat /dev/hda2
dosfsck 2.10, 22 Sep 2003, FAT32, LFN
Read 512 bytes at 0:Input/output error
root@ttyp0[knoppix]# fsck.vfat /dev/hda1
dosfsck 2.10, 22 Sep 2003, FAT32, LFN
Read 512 bytes at 0:Input/output error

---------
lspci
---------00:00.0 Host bridge: Intel Corp. 82865G/PE/P Processor to I/O Controller (rev 02)
00:01.0 PCI bridge: Intel Corp. 82865G/PE/P Processor to AGP Controller (rev 02)
00:1d.0 USB Controller: Intel Corp. 82801EB USB (rev 02)
00:1d.1 USB Controller: Intel Corp. 82801EB USB (rev 02)
00:1d.2 USB Controller: Intel Corp. 82801EB USB (rev 02)
00:1d.3 USB Controller: Intel Corp. 82801EB USB (rev 02)
00:1d.7 USB Controller: Intel Corp. 82801EB USB2 (rev 02)
00:1e.0 PCI bridge: Intel Corp. 82801BA/CA/DB/EB PCI Bridge (rev c2)
00:1f.0 ISA bridge: Intel Corp. 82801EB LPC Interface Controller (rev 02)
00:1f.1 IDE interface: Intel Corp. 82801EB Ultra ATA Storage Controller (rev 02)
00:1f.3 SMBus: Intel Corp. 82801EB SMBus Controller (rev 02)
00:1f.5 Multimedia audio controller: Intel Corp. 82801EB AC'97 Audio Controller (rev 02)
01:00.0 VGA compatible controller: ATI Technologies Inc: Unknown device 5964 (rev 01)
01:00.1 Display controller: ATI Technologies Inc: Unknown device 5d44 (rev 01)
02:05.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL-8139/8139C/8139C+ (rev 10)

Помогите помочь :) Мне ничего в голову не лезет кроме того, что hd сломался.

Ссылка

←	Ус , 264е ядро пилим и такое чудо (сарга)

2DenJS про Нвидиа в дебане :)

→

------------------
dmesg
------------------
0:36:25 CEST 2003
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009f800 (usable)
BIOS-e820: 000000000009f800 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000001fff0000 (usable)
BIOS-e820: 000000001fff0000 - 000000001fff3000 (ACPI NVS)
BIOS-e820: 000000001fff3000 - 0000000020000000 (ACPI data)
BIOS-e820: 00000000fec00000 - 0000000100000000 (reserved)
0MB HIGHMEM available.
511MB LOWMEM available.
found SMP MP-table at 000f56b0
hm, page 000f5000 reserved twice.
hm, page 000f6000 reserved twice.
hm, page 000f0000 reserved twice.
hm, page 000f1000 reserved twice.
On node 0 totalpages: 131056
zone(0): 4096 pages.
zone(1): 126960 pages.
zone(2): 0 pages.
Intel MultiProcessor Specification v1.4
Virtual Wire compatibility mode.
OEM ID: OEM00000 Product ID: PROD00000000 APIC at: 0xFEE00000
Processor #0 Pentium 4(tm) XEON(tm) APIC version 17
I/O APIC #2 Version 17 at 0xFEC00000.
Enabling APIC mode: Flat. Using 1 I/O APICs
Processors: 1
Kernel command line: ramdisk_size=100000 init=/etc/init lang=us apm=power-off hda=scsi hdb=scsi hdc=scsi hdd=scsi hde=scsi hdf=scsi hdg=scsi hdh=scsi vga=791 initrd=miniroot.gz nomce quiet BOOT_IMAGE=knoppix BOOT_IMAGE=vmlinuz
ide_setup: hda=scsi
ide_setup: hdb=scsi
ide_setup: hdc=scsi
ide_setup: hdd=scsi
ide_setup: hde=scsi
ide_setup: hdf=scsi
ide_setup: hdg=scsi
ide_setup: hdh=scsi
Initializing CPU#0
Detected 2799.709 MHz processor.
Console: colour dummy device 80x25
Calibrating delay loop... 5583.66 BogoMIPS
Memory: 514768k/524224k available (1262k kernel code, 9068k reserved, 534k data, 132k init, 0k highmem)
Dentry cache hash table entries: 65536 (order: 7, 524288 bytes)
Inode cache hash table entries: 32768 (order: 6, 262144 bytes)
Mount cache hash table entries: 512 (order: 0, 4096 bytes)
Buffer cache hash table entries: 32768 (order: 5, 131072 bytes)
Page-cache hash table entries: 131072 (order: 7, 524288 bytes)
CPU: Trace cache: 12K uops, L1 D cache: 8K
CPU: L2 cache: 512K
CPU: Physical Processor ID: 0
CPU: After generic, caps: bfebfbff 00000000 00000000 00000000
CPU: Common caps: bfebfbff 00000000 00000000 00000000
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Checking 'hlt' instruction... OK.
Checking for popad bug... OK.
POSIX conformance testing by UNIFIX
mtrr: v1.40 (20010327) Richard Gooch (rgooch@atnf.csiro.au)
mtrr: detected mtrr type: Intel
CPU: Trace cache: 12K uops, L1 D cache: 8K
CPU: L2 cache: 512K
CPU: Physical Processor ID: 0
CPU: After generic, caps: bfebfbff 00000000 00000000 00000000
CPU: Common caps: bfebfbff 00000000 00000000 00000000
CPU0: Intel(R) Pentium(R) 4 CPU 2.80GHz stepping 09
per-CPU timeslice cutoff: 1463.17 usecs.
enabled ExtINT on CPU#0
ESR value before enabling vector: 00000000
ESR value after enabling vector: 00000000
Error: only one processor found.
WARNING: No sibling found for CPU 0.
ENABLING IO-APIC IRQs
Setting 2 in the phys_id_present_map
...changing IO-APIC physical APIC ID to 2 ... ok.
init IO_APIC IRQs
IO-APIC (apicid-pin) 2-0, 2-5, 2-9, 2-11, 2-20, 2-21 not connected.
..TIMER: vector=0x31 pin1=2 pin2=0
number of MP IRQ sources: 23.
number of IO-APIC #2 registers: 24.
testing the IO APIC.......................

IO APIC #2......
.... register #00: 02000000
....... : physical APIC id: 02
....... : Delivery Type: 0
....... : LTS : 0
.... register #01: 00178020
....... : max redirection entries: 0017
....... : PRQ implemented: 1
....... : IO APIC version: 0020
.... IRQ redirection table:
NR Log Phy Mask Trig IRR Pol Stat Dest Deli Vect:
00 000 00 1 0 0 0 0 0 0 00
01 001 01 0 0 0 0 0 1 1 39
02 001 01 0 0 0 0 0 1 1 31
03 001 01 0 0 0 0 0 1 1 41
04 001 01 0 0 0 0 0 1 1 49
05 000 00 1 0 0 0 0 0 0 00
06 001 01 0 0 0 0 0 1 1 51
07 001 01 0 0 0 0 0 1 1 59
08 001 01 0 0 0 0 0 1 1 61
09 000 00 1 0 0 0 0 0 0 00
0a 001 01 0 0 0 0 0 1 1 69
0b 000 00 1 0 0 0 0 0 0 00
0c 001 01 0 0 0 0 0 1 1 71
0d 001 01 0 0 0 0 0 1 1 79
0e 001 01 0 0 0 0 0 1 1 81
0f 001 01 0 0 0 0 0 1 1 89
10 001 01 1 1 0 1 0 1 1 91
11 001 01 1 1 0 1 0 1 1 99
12 001 01 1 1 0 1 0 1 1 A1
13 001 01 1 1 0 1 0 1 1 A9
14 000 00 1 0 0 0 0 0 0 00
15 000 00 1 0 0 0 0 0 0 00
16 001 01 1 1 0 1 0 1 1 B1
17 001 01 1 1 0 1 0 1 1 B9
IRQ to pin mappings:
IRQ0 -> 0:2
IRQ1 -> 0:1
IRQ3 -> 0:3
IRQ4 -> 0:4
IRQ6 -> 0:6
IRQ7 -> 0:7
IRQ8 -> 0:8
IRQ10 -> 0:10
IRQ12 -> 0:12
IRQ13 -> 0:13
IRQ14 -> 0:14
IRQ15 -> 0:15
IRQ16 -> 0:16
IRQ17 -> 0:17
IRQ18 -> 0:18
IRQ19 -> 0:19
IRQ22 -> 0:22
IRQ23 -> 0:23
.................................... done.
Using local APIC timer interrupts.
calibrating APIC timer ...
..... CPU clock speed is 2799.7820 MHz.
..... host bus clock speed is 199.9841 MHz.
cpu: 0, clocks: 1999841, slice: 999920
CPU0<T0:1999840,T1:999920,D:0,S:999920,C:1999841>
Waiting on wait_init_idle (map = 0x0)
All processors have done init_idle
PCI: PCI BIOS revision 2.10 entry at 0xfbb60, last bus=2
PCI: Using configuration type 1
PCI: Probing PCI hardware
PCI: Probing PCI hardware (bus 00)
PCI: Ignoring BAR0-3 of IDE controller 00:1f.1
Transparent bridge - Intel Corp. 82801BA/CA/DB/EB PCI Bridge
PCI: Using IRQ router PIIX [8086/24d0] at 00:1f.0
PCI->APIC IRQ transform: (B0,I29,P0) -> 16
PCI->APIC IRQ transform: (B0,I29,P1) -> 19
PCI->APIC IRQ transform: (B0,I29,P2) -> 18
PCI->APIC IRQ transform: (B0,I29,P0) -> 16
PCI->APIC IRQ transform: (B0,I29,P3) -> 23
PCI->APIC IRQ transform: (B0,I31,P0) -> 16
PCI->APIC IRQ transform: (B0,I31,P1) -> 17
PCI->APIC IRQ transform: (B0,I31,P1) -> 17
PCI->APIC IRQ transform: (B1,I0,P0) -> 16
PCI->APIC IRQ transform: (B2,I5,P0) -> 22
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket

Selecter ★★★★
(07.08.04 20:29:37 MSD) автор топика

Ответ на: комментарий от Selecter 07.08.04 20:29:37 MSD

Starting kswapd
VFS: Disk quotas vdquot_6.5.1
vesafb: framebuffer at 0xe8000000, mapped to 0xe080d000, size 3072k
vesafb: mode is 1024x768x16, linelength=2048, pages=84
vesafb: protected mode interface info at c000:547f
vesafb: scrolling: redraw
vesafb: directcolor: size=0:5:6:5, shift=0:11:5:0
Console: switching to colour frame buffer device 128x48
fb0: VESA VGA frame buffer device
pty: 256 Unix98 ptys configured
Floppy drive(s): fd0 is 1.44M
FDC 0 is a post-1991 82077
RAMDISK driver initialized: 16 RAM disks of 100000K size 1024 blocksize
Uniform Multi-Platform E-IDE driver Revision: 7.00beta4-2.4
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
ICH5: IDE controller at PCI slot 00:1f.1
ICH5: chipset revision 2
ICH5: not 100% native mode: will probe irqs later
ide0: BM-DMA at 0xf000-0xf007, BIOS settings: hda:DMA, hdb:pio
ide1: BM-DMA at 0xf008-0xf00f, BIOS settings: hdc:DMA, hdd:pio
hda: probing with STATUS(0x50) instead of ALTSTATUS(0x7f)
hda: SAMSUNG SP0802N, ATA DISK drive
hdb: probing with STATUS(0x00) instead of ALTSTATUS(0x7f)
hdb: probing with STATUS(0x00) instead of ALTSTATUS(0x7f)
hdc: SAMSUNG CDRW/DVD SM-352B, ATAPI CD/DVD-ROM drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
ide1 at 0x170-0x177,0x376 on irq 15
hda: attached ide-disk driver.
hda: recal_intr: status=0xd0 { Busy }

hda: host protected area => 1
hda: task_no_data_intr: status=0xd0 { Busy }

hda: task_no_data_intr: status=0xd0 { Busy }

hda: task_no_data_intr: status=0xd0 { Busy }

hda: -791621424 sectors (1793713 MB) w/2048KiB Cache, CHS=218073/255/63
hda: set_multmode: status=0xd0 { Busy }
hda: recal_intr: status=0xd0 { Busy }

ide-cd: passing drive hdc to ide-scsi emulation.
hdc: attached ide-scsi driver.
Partition check:
hda: hda1 hda2 <hda: read_intr: status=0x59 { DriveReady SeekComplete DataRequest Error }
hda: read_intr: error=0x40 { UncorrectableError }, LBAsect=278689707030400, high=16611200, low=16611200, sector=117274496
end_request: I/O error, dev 03:00 (hda), sector 117274496
hda: read_intr: status=0x59 { DriveReady SeekComplete DataRequest Error }
hda: read_intr: error=0x01 { AddrMarkNotFound }, LBAsect=278689740584834, high=16611202, low=16611202, sector=117274498
hda: read_intr: status=0x59 { DriveReady SeekComplete DataRequest Error }
hda: read_intr: error=0x01 { AddrMarkNotFound }, LBAsect=278689740584834, high=16611202, low=16611202, sector=117274498
hda: recal_intr: status=0xd0 { Busy }

ide0: reset: master: error (0x00?)
hda: read_intr: status=0x59 { DriveReady SeekComplete DataRequest Error }
hda: read_intr: error=0x01 { AddrMarkNotFound }, LBAsect=278689740584834, high=16611202, low=16611202, sector=117274498
hda: read_intr: status=0x59 { DriveReady SeekComplete DataRequest Error }
hda: read_intr: error=0x01 { AddrMarkNotFound }, LBAsect=278689740584834, high=16611202, low=16611202, sector=117274498
hda: recal_intr: status=0xd0 { Busy }

ide0: reset: master: error (0x00?)
end_request: I/O error, dev 03:00 (hda), sector 117274498
end_request: I/O error, dev 03:00 (hda), sector 117274500
end_request: I/O error, dev 03:00 (hda), sector 117274502
end_request: I/O error, dev 03:00 (hda), sector 117274496
end_request: I/O error, dev 03:00 (hda), sector 117274498
end_request: I/O error, dev 03:00 (hda), sector 117274500
end_request: I/O error, dev 03:00 (hda), sector 117274502
>
ide: late registration of driver.
end_request: I/O error, dev 03:00 (hda), sector 3503342680
pdcraid: Error reading superblock.
end_request: I/O error, dev 03:00 (hda), sector 3503342680
pdcraid: Error reading superblock.
Promise Fasttrak(tm) Softwareraid driver 0.03beta: No raid array found
Highpoint HPT370 Softwareraid driver for linux version 0.02
end_request: I/O error, dev 03:00 (hda), sector 8
hptraid: Error reading superblock.
end_request: I/O error, dev 03:00 (hda), sector 8
hptraid: Error reading superblock.
end_request: I/O error, dev 03:00 (hda), sector 8
hptraid: Error reading superblock.
end_request: I/O error, dev 03:00 (hda), sector 8
hptraid: Error reading superblock.
Guestimating sector -791640872 for superblock
end_request: I/O error, dev 03:00 (hda), sector 3503326424
silraid: Error reading superblock.
driver for Silicon Image(tm) Medley(tm) hardware version 0.0.1: No raid array found
SCSI subsystem driver Revision: 1.00
scsi0 : SCSI host adapter emulation for IDE ATAPI devices
Vendor: SAMSUNG Model: CDRW/DVD SM-352B Rev: T807
Type: CD-ROM ANSI SCSI revision: 02
Attached scsi CD-ROM sr0 at scsi0, channel 0, id 0, lun 0
sr0: scsi3-mmc drive: 40x/40x writer cd/rw xa/form2 cdda tray
Uniform CD-ROM driver Revision: 3.12

Selecter ★★★★
(07.08.04 20:30:38 MSD) автор топика

Ответ на: комментарий от Selecter 07.08.04 20:30:38 MSD

Initializing Cryptographic API
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP, IGMP
IP: routing cache hash table of 4096 buckets, 32Kbytes
TCP: Hash tables configured (established 32768 bind 32768)
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
RAMDISK: Compressed image found at block 0
Freeing initrd memory: 478k freed
EXT2-fs warning: checktime reached, running e2fsck is recommended
VFS: Mounted root (ext2 filesystem).
NCR53c406a: no available ports found
aec671x_detect:
scsi: <fdomain> Detection failed (no card)
GDT: Storage RAID Controller Driver. Version: 2.05
GDT: Found 0 PCI Storage RAID Controllers
megaraid: v1.18f (Release Date: Tue Dec 10 09:54:39 EST 2002)
megaraid: no BIOS enabled.
DC390: 0 adapters found
Failed initialization of WD-7000 SCSI card!
ISO 9660 Extensions: Microsoft Joliet Level 3
kmod: failed to exec /sbin/modprobe -s -k nls_iso8859-1, errno = 2
kmod: failed to exec /sbin/modprobe -s -k nls_iso8859-1, errno = 2
ISO 9660 Extensions: RRIP_1991A
cloop: Initializing cloop v2.00
cloop: /cdrom/KNOPPIX/KNOPPIX: 29973 blocks, 65536 bytes/block, largest block is 65562 bytes.
cloop: loaded (max 8 devices)
ISO 9660 Extensions: RRIP_1991A
Freeing unused kernel memory: 132k freed
Real Time Clock Driver v1.10e
apm: BIOS version 1.2 Flags 0x07 (Driver version 1.16)
Linux Kernel Card Services 3.1.22
options: [pci] [cardbus] [pm]
Intel PCIC probe: not found.
Databook TCIC-2 PCMCIA probe: not found.
unloading Kernel Card Services
usb.c: registered new driver usbdevfs
usb.c: registered new driver hub
usb-uhci.c: $Revision: 1.275 $ time 20:50:29 Oct 3 2003
usb-uhci.c: High bandwidth mode enabled
PCI: Setting latency timer of device 00:1d.0 to 64
usb-uhci.c: USB UHCI at I/O 0xe300, IRQ 16
usb-uhci.c: Detected 2 ports
usb.c: new USB bus registered, assigned bus number 1
hub.c: USB hub found
hub.c: 2 ports detected
PCI: Setting latency timer of device 00:1d.1 to 64
usb-uhci.c: USB UHCI at I/O 0xe000, IRQ 19
usb-uhci.c: Detected 2 ports
usb.c: new USB bus registered, assigned bus number 2
hub.c: USB hub found
hub.c: 2 ports detected
PCI: Setting latency timer of device 00:1d.2 to 64
usb-uhci.c: USB UHCI at I/O 0xe100, IRQ 18
usb-uhci.c: Detected 2 ports
usb.c: new USB bus registered, assigned bus number 3
hub.c: USB hub found
hub.c: 2 ports detected
PCI: Setting latency timer of device 00:1d.3 to 64
usb-uhci.c: USB UHCI at I/O 0xe200, IRQ 16
usb-uhci.c: Detected 2 ports
usb.c: new USB bus registered, assigned bus number 4
hub.c: USB hub found
hub.c: 2 ports detected
usb-uhci.c: v1.275:USB Universal Host Controller Interface driver
usbdevfs: remount parameter error
Serial driver version 5.05c (2001-07-08) with MANY_PORTS SHARE_IRQ SERIAL_PCI ISAPNP enabled
ttyS00 at 0x03f8 (irq = 4) is a 16550A
ttyS01 at 0x02f8 (irq = 3) is a 16550A
parport0: PC-style at 0x378 [PCSPP,TRISTATE]
parport0: irq 7 detected
i810_rng: RNG not detected
8139too Fast Ethernet driver 0.9.26
eth0: RealTek RTL8139 Fast Ethernet at 0xe0bb8000, 00:04:61:54:15:b0, IRQ 22
eth0: Identified 8139 chip type 'RTL-8139C'
Intel 810 + AC97 Audio, version 0.24, 20:49:17 Oct 3 2003
PCI: Setting latency timer of device 00:1f.5 to 64
i810: Intel ICH5 found at IO 0xe600 and 0xe500, MEM 0xfc001000 and 0xfc002000, IRQ 17
i810: Intel ICH5 mmio at 0xe0bc8000 and 0xe0bca000
i810_audio: Primary codec has ID 0
i810_audio: Audio Controller supports 6 channels.
i810_audio: Defaulting to base 2 channel mode.
i810_audio: Resetting connection 0
i810_audio: Connection 0 with codec id 0
ac97_codec: AC97 codec, id: ALG96 (Unknown)
i810_audio: only 48Khz playback available.
i810_audio: AC'97 codec 0 Unable to map surround DAC's (or DAC's not present), total channels = 2
Linux agpgart interface v0.99 (c) Jeff Hartmann
agpgart: Maximum main memory to use for agp memory: 439M
agpgart: Detected an Intel(R) 865G, but could not find the secondary device. Assuming a non-integrated video card.
agpgart: Detected Intel(R) 865G chipset
agpgart: AGP aperture is 128M @ 0xe0000000
end_request: I/O error, dev 03:01 (hda), sector 0
end_request: I/O error, dev 03:01 (hda), sector 2
end_request: I/O error, dev 03:01 (hda), sector 4
end_request: I/O error, dev 03:01 (hda), sector 6