wvdial и ZTE Evolution (CDMA телефон)

[root@port ~]# lsusb | grep Qual
Bus 004 Device 012: ID 05c6:3900 Qualcomm, Inc.
[root@port ~]# modprobe usbserial vendor=0x05c6 product=0x3900
[root@port ~]# wvdialconf 
Editing `/etc/wvdial.conf'.

Scanning your serial ports for a modem.

Modem Port Scan<*1>: S0   S1   S2   S3   
WvModem<*1>: Cannot get information for serial port.
ttyUSB0<*1>: ATQ0 V1 E1 -- OK
ttyUSB0<*1>: ATQ0 V1 E1 Z -- OK
ttyUSB0<*1>: ATQ0 V1 E1 S0=0 -- OK
ttyUSB0<*1>: ATQ0 V1 E1 S0=0 &C1 -- OK
ttyUSB0<*1>: ATQ0 V1 E1 S0=0 &C1 &D2 -- OK
ttyUSB0<*1>: ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0 -- OK
ttyUSB0<*1>: Modem Identifier: ATI -- Manufacturer: ZTE INCORPORATED
ttyUSB0<*1>: Speed 9600: AT -- OK
ttyUSB0<*1>: Max speed is 9600; that should be safe.
ttyUSB0<*1>: ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0 -- OK
WvModem<*1>: Cannot get information for serial port.
ttyUSB1<*1>: ATQ0 V1 E1 -- failed with 2400 baud, next try: 9600 baud
ttyUSB1<*1>: ATQ0 V1 E1 -- failed with 9600 baud, next try: 9600 baud
ttyUSB1<*1>: ATQ0 V1 E1 -- and failed too at 115200, giving up.

Found a modem on /dev/ttyUSB0.
Modem configuration written to /etc/wvdial.conf.
ttyUSB0<Info>: Speed 9600; init "ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0"

[root@port ~]# cat /etc/wvdial.conf 
[Dialer Defaults]
Init1 = ATZ
Init2 = ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0
Modem Type = Analog Modem
ISDN = 0
Phone = #777
Modem = /dev/ttyUSB0
Username = 80921234567@people.net.ua
Password = 123
Baud = 9600

[root@port ~]# wvdial
--> WvDial: Internet dialer version 1.61
--> Cannot get information for serial port.
--> Initializing modem.
--> Sending: ATZ
ATZ
OK
--> Sending: ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0
ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0
OK
--> Modem initialized.
--> Sending: ATDT#777
--> Waiting for carrier.
ATDT#777
CONNECT
--> Carrier detected.  Waiting for prompt.
--> Connected, but carrier signal lost!  Retrying...
--> Sending: ATDT#777
--> Waiting for carrier.
~[7f]}#@!}!}!} }9}"}&} } } } }#}%B#}%}%}&p}&,!}'}"}(}";[14]~~[7f]}#@!}!}"} }9}"}&} } } } }#}%B#}%}%}&p}&,!}'}"}(}"wy~~[7f]}#@!}!}#} }9}"}&} } } } }#}%B#}%}%}&p}&,!}'}"}(}"3"~~[7f]}#@!}!}$} }9}"}&} } } } }#}%B#}%}%}&p}&,!}'}"}(}"}^*~~[7f]}#@!}!}%} }9}"}&} } } } }#}%B#}%}%}&p}&,!}'}"}(}":q~~[7f]}#@!}!}&} }9}"}&} } } } }#}%B#}%}%}&p}&,!}'}"}(}"v}<~~[7f]}#@!}!}'} }9}"}&} } } } }#}%B#}%}%}&p}&,!}'}"}(}"2G~~[7f]}#@!}!}(} }9}"}&} } } } }#}%B#}%}%}&p}&,!}'}"}(}"}]}%~~[7f]}#@!}!})} }9}"}&} } } } }#}%B#}%}%}&p}&,!}'}"}(}"9^~~[7f]}#@!}!}*} }9}"}&} } } } }#}%B#}%}%}&p}&,!}'}"}(}"u3~
--> Timed out while dialing.  Trying again.
--> Sending: ATDT#777
--> Waiting for carrier.
--> Timed out while dialing.  Trying again.
--> Sending: ATDT#777
--> Waiting for carrier.
--> Timed out while dialing.  Trying again.
--> Sending: ATDT#777
--> Waiting for carrier.
~[7f]}#@!}!}!} }9}"}&} } } } }#}%B#}%}%}&(|md}'}"}(}"Q[12]~~[7f]}#@!}!}"} }9}"}&} } } } }#}%B#}%}%}&(|md}'}"}(}"}=[7f]~~[7f]}#@!}!}#} }9}"}&} } } } }#}%B#}%}%}&(|md}'}"}(}"Y$~~[7f]}#@!}!}$} }9}"}&} } } } }#}%B#}%}%}&(|md}'}"}(}"[14],~~[7f]}#@!}!}%} }9}"}&} } } } }#}%B#}%}%}&(|md}'}"}(}"Pw~~[7f]}#@!}!}&} }9}"}&} } } } }#}%B#}%}%}&(|md}'}"}(}"}<}:~~[7f]}#@!}!}'} }9}"}&} } } } }#}%B#}%}%}&(|md}'}"}(}"XA~~[7f]}#@!}!}(} }9}"}&} } } } }#}%B#}%}%}&(|md}'}"}(}"[17]}#~~[7f]}#@!}!})} }9}"}&} } } } }#}%B#}%}%}&(|md}'}"}(}"SX~~[7f]}#@!}!}*} }9}"}&} } } } }#}%B#}%}%}&(|md}'}"}(}"}?5~