Надоело запускать вручную bumbleebeed -D ,нашел на арчвики решение, удалил bumblebee.socket, не помогло
rc-update show
alsasound | boot
bootmisc | boot
bumblebee | default
devfs | sysinit
dmesg | sysinit
fsck | boot
hostname | boot
hwclock | boot
keymaps | boot
killprocs | shutdown
local | default
localmount | boot
loopback | boot
modules | boot
mount-ro | shutdown
mtab | boot
netmount | default
procfs | boot
root | boot
savecache | shutdown
swap | boot
swapfiles | boot
sysctl | boot
sysfs | sysinit
syslog-ng | default
termencoding | boot
tmpfiles.dev | sysinit
tmpfiles.setup | boot
udev | sysinit
udev-mount | sysinit
urandom | boot
xdm | default cat /etc/group
root:x:0:root
bin:x:1:root,bin,daemon
daemon:x:2:root,bin,daemon
sys:x:3:root,bin,adm
adm:x:4:root,adm,daemon
tty:x:5:
disk:x:6:root,adm
lp:x:7:lp
mem:x:8:
kmem:x:9:
wheel:x:10:root,freemann9
floppy:x:11:root
news:x:13:news
uucp:x:14:uucp
console:x:17:
audio:x:18:freemann9
cdrom:x:19:
tape:x:26:root
video:x:27:root,freemann9
cdrw:x:80:
usb:x:85:
users:x:100:freemann9
portage:x:250:portage
utmp:x:406:
nogroup:x:65533:
nobody:x:65534:
man:x:15:
sshd:x:22:
messagebus:x:249:
ldap:x:439:
lpadmin:x:106:
freemann9:x:1000:
bumblebee:x:105:freemann9
polkitd:x:104:
plugdev:x:103:
# Configuration file for Bumblebee. Values should **not** be put between quotes
## Server options. Any change made in this section will need a server restart
# to take effect.
[bumblebeed]
# The secondary Xorg server DISPLAY number
VirtualDisplay=:8
# Should the unused Xorg server be kept running? Set this to true if waiting
# for X to be ready is too long and don't need power management at all.
KeepUnusedXServer=false
# The name of the Bumbleblee server group name (GID name)
ServerGroup=bumblebee
# Card power state at exit. Set to false if the card shoud be ON when Bumblebee
# server exits.
TurnCardOffAtExit=false
# The default behavior of '-f' option on optirun. If set to "true", '-f' will
# be ignored.
NoEcoModeOverride=false
# The Driver used by Bumblebee server. If this value is not set (or empty),
# auto-detection is performed. The available drivers are nvidia and nouveau
# (See also the driver-specific sections below)
Driver=nvidia
# Directory with a dummy config file to pass as a -configdir to secondary X
XorgConfDir=/etc/bumblebee/xorg.conf.d
## Client options. Will take effect on the next optirun executed.
[optirun]
# Acceleration/ rendering bridge, possible values are auto, virtualgl and
# primus.
Bridge=primus
# The method used for VirtualGL to transport frames between X servers.
# Possible values are proxy, jpeg, rgb, xv and yuv.
VGLTransport=proxy
# List of paths which are searched for the primus libGL.so.1 when using
# the primus bridge
PrimusLibraryPath=/usr/lib/primus:/usr/lib32/primus
# Should the program run under optirun even if Bumblebee server or nvidia card
# is not available?
AllowFallbackToIGC=false
# Driver-specific settings are grouped under [driver-NAME]. The sections are
# parsed if the Driver setting in [bumblebeed] is set to NAME (or if auto-
# detection resolves to NAME).
# PMMethod: method to use for saving power by disabling the nvidia card, valid
# values are: auto - automatically detect which PM method to use
# bbswitch - new in BB 3, recommended if available
# switcheroo - vga_switcheroo method, use at your own risk
# none - disable PM completely
# https://github.com/Bumblebee-Project/Bumblebee/wiki/Comparison-of-PM-methods
## Section with nvidia driver specific options, only parsed if Driver=nvidia
[driver-nvidia]
# Module name to load, defaults to Driver if empty or unset
KernelDriver=nvidia
PMMethod=auto
# colon-separated path to the nvidia libraries
LibraryPath=/usr/lib64/opengl/nvidia/lib:/usr/lib32/opengl/nvidia/lib:/usr/lib/opengl/nvidia/lib
# comma-separated path of the directory containing nvidia_drv.so and the
# default Xorg modules path
XorgModulePath=/usr/lib64/opengl/nvidia/lib,/usr/lib64/opengl/nvidia/extensions,/usr/lib64/xorg/modules/drivers,/usr/lib64/xorg/modules
XorgConfFile=/etc/bumblebee/xorg.conf.nvidia
