PMCI COM-порт

что говорит dmesg?

$ dmesg
Linux version 2.6.14-1.1653.1asp (build@amd64.asplinux.com.ua) (gcc version 4.0.2 20051125 (Red Hat 4.0.2-8)) #1 Mon Jan 23 19:24:56 EET 2006
...
PNP: PS/2 Controller [PNP0303:C161,PNP0f13:C162] at 0x60,0x64 irq 1,12
i8042.c: Detected active multiplexing controller, rev 1.1.
serio: i8042 AUX0 port at 0x60,0x64 irq 12
serio: i8042 AUX1 port at 0x60,0x64 irq 12
serio: i8042 AUX2 port at 0x60,0x64 irq 12
serio: i8042 AUX3 port at 0x60,0x64 irq 12
serio: i8042 KBD port at 0x60,0x64 irq 1
Serial: 8250/16550 driver $Revision: 1.90 $ 32 ports, IRQ sharing enabled
ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
ttyS2 at I/O 0x3e8 (irq = 3) is a NS16550A
ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered
RAMDISK driver initialized: 16 RAM disks of 16384K size 1024 blocksize
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
ICH3M: IDE controller at PCI slot 0000:00:1f.1
PCI: Enabling device 0000:00:1f.1 (0005 -> 0007)
PCI: setting IRQ 11 as level-triggered
PCI: Assigned IRQ 11 for device 0000:00:1f.1
ICH3M: chipset revision 2
ICH3M: not 100% native mode: will probe irqs later
    ide0: BM-DMA at 0x4440-0x4447, BIOS settings: hda:DMA, hdb:pio
    ide1: BM-DMA at 0x4448-0x444f, BIOS settings: hdc:DMA, hdd:pio
Probing IDE interface ide0...
...
usbcore: registered new driver hiddev
usbcore: registered new driver usbhid
drivers/usb/input/hid-core.c: v2.6:USB HID core driver
mice: PS/2 mouse device common for all mice
md: md driver 0.90.2 MAX_MD_DEVS=256, MD_SB_DISKS=27
md: bitmap version 3.39
NET: Registered protocol family 2
...
EXT3-fs: INFO: recovery required on readonly filesystem.
...
e100: Intel(R) PRO/100 Network Driver, 3.4.14-k2-NAPI
e100: Copyright(c) 1999-2005 Intel Corporation
...
PCI: Found IRQ 11 for device 0000:02:06.0
Yenta: CardBus bridge found at 0000:02:06.0 [0e11:004a]
Yenta: Enabling burst memory read transactions
Yenta: Using CSCINT to route CSC interrupts to PCI
Yenta: Routing CardBus interrupts to PCI
Yenta TI: socket 0000:02:06.0, mfunc 0x012c1202, devctl 0x64
Yenta: ISA IRQ mask 0x0098, PCI irq 11
Socket status: 30000020
pcmcia: parent PCI bridge I/O window: 0x2000 - 0x2fff
cs: IO port probe 0x2000-0x2fff: clean.
pcmcia: parent PCI bridge Memory window: 0x40000000 - 0x402fffff
pcmcia: parent PCI bridge Memory window: 0x20000000 - 0x21ffffff
PCI: Enabling device 0000:03:00.0 (0000 -> 0003)
NET: Registered protocol family 10
Disabled Privacy Extensions on device c0388660(lo)
IPv6 over IPv4 tunneling driver
...

Как на счет модуля serial_cs. Он должен твою железку завести.

По modprobe модуль подгружается, в dmesg по этому поводу ничего не появляется. Кажется, что мимо...