LINUX.ORG.RU
Форум — Linux-hardware  

Слетает DMA с HDD


0

0 

Время от времени происходит следующее:

hda: status error: status=0x00 { }
ide: failed opcode was: unknown
hda: drive not ready for command
hda: status error: status=0x00 { }
ide: failed opcode was: unknown
hda: drive not ready for command
hda: status error: status=0x00 { }
ide: failed opcode was: unknown
hda: drive not ready for command
hda: status error: status=0x00 { }
ide: failed opcode was: unknown
hda: DMA disabled
hdb: DMA disabled
hda: drive not ready for command
ide0: reset: success

Один из винтов при этом выключается и включается снова (это слышно).
Если его снять, такая же ситуация снова через некоторое время повторяется.

DMA обратно легко поднимается с помощью hdparm.

Это винты умирают или контроллер? В чём ещё может быть дело?
★★★★
← Кто-нибудь использовал ноут Samsung R-25
Intel Corporation PRO/Wireless 3945ABG on PR600 MegaBook & Debian lenny → 

Первый винт

% sudo /usr/sbin/smartctl -s on -a -d ata /dev/hda
smartctl version 5.37 [i686-pc-linux-gnu] Copyright (C) 2002-6 Bruce Allen
Home page is http://smartmontools.sourceforge.net/

=== START OF INFORMATION SECTION ===
Model Family:     Western Digital Caviar SE family
Device Model:     WDC WD3200JB-00KFA0
Serial Number:    WD-WCAMR3896887
Firmware Version: 08.05J08
User Capacity:    320 072 933 376 bytes
Device is:        In smartctl database [for details use: -P show]
ATA Version is:   6
ATA Standard is:  Exact ATA specification draft version not indicated
Local Time is:    Mon Sep 10 15:15:26 2007 MSD
SMART support is: Available - device has SMART capability.
SMART support is: Enabled

=== START OF ENABLE/DISABLE COMMANDS SECTION ===
SMART Enabled.

=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED

General SMART Values:
Offline data collection status:  (0x84) Offline data collection activity
                                        was suspended by an interrupting command from host.
                                        Auto Offline Data Collection: Enabled.
Self-test execution status:      (   0) The previous self-test routine completed
                                        without error or no self-test has ever
                                        been run.
Total time to complete Offline
data collection:                 (9600) seconds.
Offline data collection
capabilities:                    (0x7b) SMART execute Offline immediate.
                                        Auto Offline data collection on/off support.
                                        Suspend Offline collection upon new
                                        command.
                                        Offline surface scan supported.
                                        Self-test supported.
                                        Conveyance Self-test supported.
                                        Selective Self-test supported.
SMART capabilities:            (0x0003) Saves SMART data before entering
                                        power-saving mode.
                                        Supports SMART auto save timer.
Error logging capability:        (0x01) Error logging supported.
                                        No General Purpose Logging support.
Short self-test routine
recommended polling time:        (   2) minutes.
Extended self-test routine
recommended polling time:        ( 116) minutes.
Conveyance self-test routine
recommended polling time:        (   6) minutes.

SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME          FLAG     VALUE WORST THRESH TYPE      UPDATED  WHEN_FAILED RAW_VALUE
  1 Raw_Read_Error_Rate     0x000f   200   200   051    Pre-fail  Always       -       0
  3 Spin_Up_Time            0x0003   196   194   021    Pre-fail  Always       -       5175
  4 Start_Stop_Count        0x0032   100   100   000    Old_age   Always       -       86
  5 Reallocated_Sector_Ct   0x0033   200   200   140    Pre-fail  Always       -       0
  7 Seek_Error_Rate         0x000f   200   200   051    Pre-fail  Always       -       0
  9 Power_On_Hours          0x0032   096   096   000    Old_age   Always       -       3604
 10 Spin_Retry_Count        0x0013   100   253   051    Pre-fail  Always       -       0
 11 Calibration_Retry_Count 0x0012   100   253   051    Old_age   Always       -       0
 12 Power_Cycle_Count       0x0032   100   100   000    Old_age   Always       -       85
194 Temperature_Celsius     0x0022   112   087   000    Old_age   Always       -       38
196 Reallocated_Event_Count 0x0032   200   200   000    Old_age   Always       -       0
197 Current_Pending_Sector  0x0012   200   200   000    Old_age   Always       -       0
198 Offline_Uncorrectable   0x0010   200   200   000    Old_age   Offline      -       0
199 UDMA_CRC_Error_Count    0x003e   200   200   000    Old_age   Always       -       0
200 Multi_Zone_Error_Rate   0x0009   200   200   051    Pre-fail  Offline      -       0

SMART Error Log Version: 1
No Errors Logged

SMART Self-test log structure revision number 1
No self-tests have been logged.  [To run self-tests, use: smartctl -t]


SMART Selective self-test log data structure revision number 1
 SPAN  MIN_LBA  MAX_LBA  CURRENT_TEST_STATUS
    1        0        0  Not_testing
    2        0        0  Not_testing
    3        0        0  Not_testing
    4        0        0  Not_testing
    5        0        0  Not_testing
Selective self-test flags (0x0):
  After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.

kaktyc ★★★★
() автор топика 

Второй винт

% sudo /usr/sbin/smartctl -s on -a -d ata /dev/hdb
smartctl version 5.37 [i686-pc-linux-gnu] Copyright (C) 2002-6 Bruce Allen
Home page is http://smartmontools.sourceforge.net/

=== START OF INFORMATION SECTION ===
Model Family:     Western Digital Caviar SE family
Device Model:     WDC WD800JB-00FMA0
Serial Number:    WD-WMAJ91156503
Firmware Version: 13.03G13
User Capacity:    80 026 361 856 bytes
Device is:        In smartctl database [for details use: -P show]
ATA Version is:   6
ATA Standard is:  Exact ATA specification draft version not indicated
Local Time is:    Mon Sep 10 15:15:48 2007 MSD
SMART support is: Available - device has SMART capability.
SMART support is: Enabled

=== START OF ENABLE/DISABLE COMMANDS SECTION ===
SMART Enabled.

=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
See vendor-specific Attribute list for marginal Attributes.

General SMART Values:
Offline data collection status:  (0x02) Offline data collection activity
                                        was completed without error.
                                        Auto Offline Data Collection: Disabled.
Self-test execution status:      (   0) The previous self-test routine completed
                                        without error or no self-test has ever
                                        been run.
Total time to complete Offline
data collection:                 (2460) seconds.
Offline data collection
capabilities:                    (0x7b) SMART execute Offline immediate.
                                        Auto Offline data collection on/off support.
                                        Suspend Offline collection upon new
                                        command.
                                        Offline surface scan supported.
                                        Self-test supported.
                                        Conveyance Self-test supported.
                                        Selective Self-test supported.
SMART capabilities:            (0x0003) Saves SMART data before entering
                                        power-saving mode.
                                        Supports SMART auto save timer.
Error logging capability:        (0x01) Error logging supported.
                                        No General Purpose Logging support.
Short self-test routine
recommended polling time:        (   2) minutes.
Extended self-test routine
recommended polling time:        (  35) minutes.
Conveyance self-test routine
recommended polling time:        (   5) minutes.

SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME          FLAG     VALUE WORST THRESH TYPE      UPDATED  WHEN_FAILED RAW_VALUE
  1 Raw_Read_Error_Rate     0x000b   200   179   051    Pre-fail  Always       -       0
  3 Spin_Up_Time            0x0007   103   096   021    Pre-fail  Always       -       2225
  4 Start_Stop_Count        0x0032   099   099   040    Old_age   Always       -       1724
  5 Reallocated_Sector_Ct   0x0033   200   200   140    Pre-fail  Always       -       0
  7 Seek_Error_Rate         0x000b   200   200   051    Pre-fail  Always       -       0
  9 Power_On_Hours          0x0032   069   069   000    Old_age   Always       -       22648
 10 Spin_Retry_Count        0x0013   100   100   051    Pre-fail  Always       -       0
 11 Calibration_Retry_Count 0x0013   100   100   051    Pre-fail  Always       -       0
 12 Power_Cycle_Count       0x0032   099   099   000    Old_age   Always       -       1660
194 Temperature_Celsius     0x0022   106   000   000    Old_age   Always   In_the_past 37
196 Reallocated_Event_Count 0x0032   200   200   000    Old_age   Always       -       0
197 Current_Pending_Sector  0x0012   200   200   000    Old_age   Always       -       0
198 Offline_Uncorrectable   0x0012   200   200   000    Old_age   Always       -       0
199 UDMA_CRC_Error_Count    0x000a   200   190   000    Old_age   Always       -       1546
200 Multi_Zone_Error_Rate   0x0009   200   200   051    Pre-fail  Offline      -       0

SMART Error Log Version: 1
ATA Error Count: 1
        CR = Command Register [HEX]
        FR = Features Register [HEX]
        SC = Sector Count Register [HEX]
        SN = Sector Number Register [HEX]
        CL = Cylinder Low Register [HEX]
        CH = Cylinder High Register [HEX]
        DH = Device/Head Register [HEX]
        DC = Device Command Register [HEX]
        ER = Error register [HEX]
        ST = Status register [HEX]
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.

Error 1 occurred at disk power-on lifetime: 43 hours (1 days + 19 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER ST SC SN CL CH DH
  -- -- -- -- -- -- --
  04 51 16 30 4f c2 a0  Error: ABRT

  Commands leading to the command that caused the error were:
  CR FR SC SN CL CH DH DC   Powered_Up_Time  Command/Feature_Name
  -- -- -- -- -- -- -- --  ----------------  --------------------
  b0 d6 01 be 4f c2 00 00      00:23:29.935  SMART WRITE LOG
  b0 d8 0b 00 4f c2 00 00      00:23:29.855  SMART ENABLE OPERATIONS
  b0 da 0b 00 4f c2 00 00      00:23:29.855  SMART RETURN STATUS
  ef 03 0b 00 00 00 00 00      00:23:29.855  SET FEATURES [Set transfer mode]
  ec 57 01 01 00 00 00 00      00:23:29.845  IDENTIFY DEVICE

SMART Self-test log structure revision number 1
Num  Test_Description    Status                  Remaining  LifeTime(hours)  LBA_of_first_error
# 1  Extended captive    Completed without error       00%        42         -
# 2  Short captive       Completed without error       00%        42         -

SMART Selective self-test log data structure revision number 1
 SPAN  MIN_LBA  MAX_LBA  CURRENT_TEST_STATUS
    1        0        0  Not_testing
    2        0        0  Not_testing
    3        0        0  Not_testing
    4        0        0  Not_testing
    5        0        0  Not_testing
Selective self-test flags (0x0):
  After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.


Это значит, что у второго винта проблемы с питанием?

kaktyc ★★★★
() автор топика
Ответ на: комментарий от kaktyc

>Это значит, что у второго винта проблемы с питанием?

не знаю как с питанием, но UDMA_CRC_Error_Count говорит - что со шлейфом.

chocholl ★★
()
Ответ на: комментарий от kaktyc

тогда либо винт, либо контролер, потому-что у тебя других серьезных ошибок нету

chocholl ★★
()
Ответ на: комментарий от kaktyc

Винты хорошо обдуваются? На эти вестерны емнип ругались, что оне отключаются-включаются от перегрева контроллера.

anonymous
()
Ответ на: комментарий от anonymous

> контроллера.

контроллер самого диска имеется в виду.

anonymous
()
Ответ на: комментарий от anonymous

>Винты хорошо обдуваются? На эти вестерны емнип ругались, что оне отключаются-включаются от перегрева контроллера.

Стоят в корзине друг над другом, есть зазор между ними. Может быть, что и перегреваются. Хотя летом при жаре работали нормально.

Похоже, второй винт подыхает. Сейчас повесил систему. Только странно, что в dmesg были сообщения про hda, а не про hdb.

kaktyc ★★★★
() автор топика

вероятней всего: БП или перегрев винтов

Muromec ☆☆
()

ловил такие же глюки именно с 80-кой WD, но сата.

Muromec ☆☆
()
Вы не можете добавлять комментарии в эту тему. Тема перемещена в архив.
← Кто-нибудь использовал ноут Samsung R-25
Linux-hardware
Intel Corporation PRO/Wireless 3945ABG on PR600 MegaBook & Debian lenny →