LINUX.ORG.RU
Форум — Linux-hardware  

Проблема со звуком через PCI в тв-тюнере


0

2

Здравствуйте, не могу решить проблему: нет звука в тв-тюнере Behold TV H7. Выбрал его из-за http://www.beholder.ru/bb/viewtopic.php?f=11&t=9294, цитируя сообщение от 7 апреля 2010 года 

Поддержка тюнера H7 уже есть в свежем video4linux.
Дистрибутив Debian 6.0.3 Squeeze , рабочая среда xfce4. Ядро поставил свежее 3.0.4. Поддержка есть в video4linux http://www.kernel.org/doc/Documentation/video4linux/CARDLIST.saa7134 . ТВ нахожу используя tvtime, но звука как небыло так нет. Отправил сообщение на форум http://www.beholder.ru/bb/viewtopic.php?f=11&t=9294, но ответа так и не получил и наверное не дождусь, поэтому обращаюсь с просьбой о помощи сюда.

Вот конфиг behold.conf из /etc/modprobe.d

Код: 

options xc5000 no_poweroff=1
options saa7134 i2c_scan=1 radio_nr=1 gbuffers=4 alsa=1 secam=d
параметр alsa=1 не помагает решить проблему с передачей звука по pci шине вот часть dmesg:

Код: 

[    5.820653] Linux video capture interface: v2.00
[    5.871292] saa7130/34: v4l2 driver version 0.2.16 loaded
[    5.871411] saa7134 0000:02:07.0: PCI INT A -> GSI 22 (level, low) -> IRQ 22
[    5.871417] saa7133[0]: found at 0000:02:07.0, rev: 209, irq: 22, latency: 64, mmio: 0xfbffb800
[    5.871423] saa7133[0]: subsystem: 5ace:7190, board: Beholder BeholdTV H7 [card=178,autodetected]
[    5.871485] saa7133[0]: board init: gpio is 0
[    5.886067] AMD64 EDAC driver v3.4.0
[    5.886174] EDAC amd64: DRAM ECC disabled.
[    5.886181] EDAC amd64: ECC disabled in the BIOS or no ECC capability, module will not load.
[    5.886182]  Either enable ECC checking or force module loading by setting 'ecc_enable_override'.
[    5.886184]  (Note that use of the override may cause unknown side effects.)
[    6.020058] saa7133[0]: i2c eeprom 00: ce 5a 90 71 54 20 00 00 00 00 00 00 00 00 00 01
[    6.020065] saa7133[0]: i2c eeprom 10: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
[    6.020071] saa7133[0]: i2c eeprom 20: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
[    6.020076] saa7133[0]: i2c eeprom 30: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
[    6.020081] saa7133[0]: i2c eeprom 40: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
[    6.020086] saa7133[0]: i2c eeprom 50: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
[    6.020091] saa7133[0]: i2c eeprom 60: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
[    6.020096] saa7133[0]: i2c eeprom 70: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
[    6.020101] saa7133[0]: i2c eeprom 80: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
[    6.020106] saa7133[0]: i2c eeprom 90: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
[    6.020111] saa7133[0]: i2c eeprom a0: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
[    6.020116] saa7133[0]: i2c eeprom b0: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
[    6.020121] saa7133[0]: i2c eeprom c0: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
[    6.020126] saa7133[0]: i2c eeprom d0: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
[    6.020131] saa7133[0]: i2c eeprom e0: d8 cf 00 00 ff ff ff ff ff ff ff ff ff ff ff ff
[    6.020136] saa7133[0]: i2c eeprom f0: 42 54 56 30 30 30 30 ff ff ff ff ff ff ff ff ff
[    6.028060] saa7133[0]: i2c scan: found device @ 0x1e  [???]
[    6.040039] saa7133[0]: i2c scan: found device @ 0x5a  [remote control]
[    6.052060] saa7133[0]: i2c scan: found device @ 0xa0  [eeprom]
[    6.060062] saa7133[0]: i2c scan: found device @ 0xc2  [???]
[    6.157210] IR NEC protocol handler initialized
[    6.427477] i2c-core: driver [tuner] using legacy suspend method
[    6.427479] i2c-core: driver [tuner] using legacy resume method
[    6.436100] tuner 1-0061: Tuner -1 found with type(s) Radio TV.
[    6.473202] IR RC5(x) protocol handler initialized
[    6.538266] xc5000 1-0061: creating new instance
[    6.544061] xc5000: Successfully identified at address 0x61
[    6.544064] xc5000: Firmware has not been loaded previously
[    6.591785] IR RC6 protocol handler initialized
[    6.664378] IR JVC protocol handler initialized
[    6.674987] IR Sony protocol handler initialized
[    6.781990] lirc_dev: IR Remote Control driver registered, major 251
[    6.791509] IR LIRC bridge handler initialized
[    6.820893] scsi 8:0:0:0: Direct-Access     Generic  USB SD Reader    1.00 PQ: 0 ANSI: 0
[    6.821414] scsi 8:0:0:1: Direct-Access     Generic  USB CF Reader    1.01 PQ: 0 ANSI: 0
[    6.822035] scsi 8:0:0:2: Direct-Access     Generic  USB SM Reader    1.02 PQ: 0 ANSI: 0
[    6.822661] scsi 8:0:0:3: Direct-Access     Generic  USB MS Reader    1.03 PQ: 0 ANSI: 0
[    6.823257] sd 8:0:0:0: Attached scsi generic sg4 type 0
[    6.823393] sd 8:0:0:1: Attached scsi generic sg5 type 0
[    6.823868] sd 8:0:0:2: Attached scsi generic sg6 type 0
[    6.824337] sd 8:0:0:3: Attached scsi generic sg7 type 0
[    6.834102] sd 8:0:0:0: [sdd] Attached SCSI removable disk
[    6.835475] sd 8:0:0:3: [sdg] Attached SCSI removable disk
[    6.836856] sd 8:0:0:1: [sde] Attached SCSI removable disk
[    6.838464] sd 8:0:0:2: [sdf] Attached SCSI removable disk
[    6.891838] HDA Intel 0000:00:14.2: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[    7.059330] HDA Intel 0000:04:00.1: PCI INT B -> GSI 19 (level, low) -> IRQ 19
[    7.059333] hda_intel: Disabling MSI
[    7.059381] HDA Intel 0000:04:00.1: setting latency timer to 64
[    7.114577] nvidia: module license 'NVIDIA' taints kernel.
[    7.114580] Disabling lock debugging due to kernel taint
[    7.840057] HDMI status: Pin=5 Presence_Detect=0 ELD_Valid=0
[    7.928057] HDMI status: Pin=5 Presence_Detect=0 ELD_Valid=0
[    8.016063] HDMI status: Pin=5 Presence_Detect=0 ELD_Valid=0
[    8.104062] HDMI status: Pin=5 Presence_Detect=0 ELD_Valid=0
[    8.232228] input: HDA NVidia HDMI/DP as /devices/pci0000:00/0000:00:02.0/0000:04:00.1/sound/card1/input6
[    8.232281] input: HDA NVidia HDMI/DP as /devices/pci0000:00/0000:00:02.0/0000:04:00.1/sound/card1/input7
[    8.232328] input: HDA NVidia HDMI/DP as /devices/pci0000:00/0000:00:02.0/0000:04:00.1/sound/card1/input8
[    8.232375] input: HDA NVidia HDMI/DP as /devices/pci0000:00/0000:00:02.0/0000:04:00.1/sound/card1/input9
[    8.233898] nvidia 0000:04:00.0: PCI INT A -> GSI 18 (level, low) -> IRQ 18
[    8.233905] nvidia 0000:04:00.0: setting latency timer to 64
[    8.233909] vgaarb: device changed decodes: PCI:0000:04:00.0,olddecodes=io+mem,decodes=none:owns=io+mem
[    8.234051] NVRM: loading NVIDIA UNIX x86_64 Kernel Module  280.13  Wed Jul 27 16:53:56 PDT 2011
[   31.148063] Registered IR keymap rc-behold
[   31.148141] input: i2c IR (BeholdTV) as /devices/virtual/rc/rc0/input10
[   31.148192] rc0: i2c IR (BeholdTV) as /devices/virtual/rc/rc0
[   31.148194] ir-kbd-i2c: i2c IR (BeholdTV) detected at i2c-1/1-002d/ir0 [saa7133[0]]
[   31.148430] saa7133[0]: registered device video0 [v4l2]
[   31.148449] saa7133[0]: registered device vbi0
[   31.148467] saa7133[0]: registered device radio1
[   31.161261] dvb_init() allocating 1 frontend
[   31.176060] xc5000 1-0061: attaching existing instance
[   31.184057] xc5000: Successfully identified at address 0x61
[   31.184059] xc5000: Firmware has not been loaded previously
[   31.184063] DVB: registering new adapter (saa7133[0])
[   31.184066] DVB: registering adapter 0 frontend 0 (Zarlink ZL10353 DVB-T)...
[   31.224061] xc5000: waiting for firmware upload (dvb-fe-xc5000-1.6.114.fw)...
[   31.269590] xc5000: firmware read 12401 bytes.
[   31.269592] xc5000: firmware uploading...
[   31.276177] xc5000: I2C read failed
[   31.276179] xc5000: xc_SetSignalSource(1) failed
[   31.276335] zl10353: write to reg 50 failed (err = -5)!
[   31.276479] zl10353: write to reg 50 failed (err = -5)!
[   31.286668] saa7134 ALSA driver for DMA sound loaded
[   31.286694] saa7133[0]/alsa: saa7133[0] at 0xfbffb800 irq 22 registered as card -1
[   36.252052] xc5000: firmware upload complete...
[   36.261147] xc5000: I2C write failed (len=4)
[   36.261175] xc5000: I2C read failed
[   36.364588] xc5000: I2C write failed (len=4)
[   36.885875] Adding 2891632k swap on /dev/sdc6.  Priority:-1 extents:1 across:2891632k
[   37.309467] EXT3-fs (sdc1): using internal journal
[   37.379211] loop: module loaded
[   39.118504] EXT4-fs (sdb5): mounted filesystem with ordered data mode. Opts: (null)
[   39.128841] EXT3-fs: barriers not enabled
[   39.129054] kjournald starting.  Commit interval 5 seconds
[   39.129443] EXT3-fs (sda5): using internal journal
[   39.129448] EXT3-fs (sda5): mounted filesystem with ordered data mode
[   39.242832] EXT3-fs: barriers not enabled
[   39.260401] kjournald starting.  Commit interval 5 seconds
[   39.260693] EXT3-fs (sdc5): using internal journal
[   39.260697] EXT3-fs (sdc5): mounted filesystem with ordered data mode
[   40.858564] r8169 0000:01:00.0: eth0: unable to load firmware patch rtl_nic/rtl8168e-2.fw (-2)
[   40.883677] r8169 0000:01:00.0: eth0: link down
[   40.883682] r8169 0000:01:00.0: eth0: link down
[   40.884648] ADDRCONF(NETDEV_UP): eth0: link is not ready
[   41.182742] fuse init (API version 7.16)
[   42.502186] r8169 0000:01:00.0: eth0: link up
[   42.503106] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[   47.400678] Bluetooth: Core ver 2.16
[   47.400695] NET: Registered protocol family 31
[   47.400697] Bluetooth: HCI device and connection manager initialized
[   47.400699] Bluetooth: HCI socket layer initialized
[   51.260658] lp: driver loaded but no devices found
[   51.469356] ppdev: user-space parallel port driver
[   52.488795] parport 0x378 (WARNING): CTR: wrote 0x0c, read 0xff
[   52.488801] parport 0x378 (WARNING): DATA: wrote 0xaa, read 0xff
[   52.488803] parport 0x378: You gave this address, but there is probably no parallel port there!
[   52.488819] parport0: PC-style at 0x378, irq 7 [PCSPP,TRISTATE]
[   52.584039] eth0: no IPv6 routers present
[   52.584190] lp0: using parport0 (interrupt-driven).
[   57.101118] xc5000: I2C write failed (len=4)
[   57.101133] xc5000: I2C write failed (len=4)
[   57.101666] xc5000: I2C read failed
[   63.950925] powernow-k8: Found 1 AMD Athlon(tm) II X2 245 Processor (2 cpu cores) (version 2.20.00)
[   63.950956] powernow-k8:    0 : pstate 0 (2900 MHz)
[   63.950958] powernow-k8:    1 : pstate 1 (2200 MHz)
[   63.950959] powernow-k8:    2 : pstate 2 (1700 MHz)
[   63.950961] powernow-k8:    3 : pstate 3 (800 MHz)

При загрузке системы долго (чуть меньше минуты) ждёт на строчке: 

Waiting for /dev to be fully populated
потом выдаёт: 
xc5000: xc_SetTVStandard failed
xc5000: I2C write failed (len=4)
xc5000: I2C write failed (len=4)
после как обычно.

Код: 

cat /var/log/syslog |grep failed
.......
Nov  4 08:36:54 debian kernel: [   31.280203] xc5000: I2C read failed
Nov  4 08:36:54 debian kernel: [   31.280206] xc5000: xc_SetSignalSource(1) failed
Nov  4 08:36:59 debian bluetoothd[1732]: Server initialization failed
Nov  4 08:37:09 debian kernel: [   55.636217] xc5000: I2C read failed
Nov  4 08:37:09 debian kernel: [   55.636220] xc5000: xc_SetSignalSource(1) failed
Nov  4 08:37:09 debian kernel: [   55.636374] xc5000: I2C read failed
Nov  4 08:37:09 debian kernel: [   55.860536] xc5000: I2C write failed (len=64)
Nov  4 08:37:09 debian kernel: [   55.864196] xc5000: I2C read failed
Nov  4 08:38:35 debian kernel: [  141.425175] xc5000: I2C write failed (len=4)
Nov  4 08:38:35 debian kernel: [  141.532093] xc5000: I2C write failed (len=4)
Nov  4 08:38:35 debian kernel: [  141.532720] xc5000: I2C read failed
Nov  4 08:38:35 debian kernel: [  141.532728] xc5000: I2C read failed
Nov  4 09:01:36 debian kernel: [ 1522.228756] xc5000: I2C write failed (len=4)
Nov  4 09:01:36 debian kernel: [ 1522.228765] xc5000: xc_SetTVStandard failed
Nov  4 09:01:44 debian kernel: [ 1530.544780] xc5000: I2C write failed (len=4)
Nov  4 09:01:44 debian kernel: [ 1530.544789] xc5000: xc_SetTVStandard failed
Nov  4 09:01:52 debian kernel: [ 1538.852774] xc5000: I2C write failed (len=4)
Nov  4 09:01:52 debian kernel: [ 1538.852782] xc5000: xc_SetTVStandard failed
Nov  4 09:02:40 debian kernel: [ 1586.272759] xc5000: I2C write failed (len=4)
Nov  4 09:02:40 debian kernel: [ 1586.272767] xc5000: xc_SetTVStandard failed
Nov  4 09:02:48 debian kernel: [ 1594.488741] xc5000: I2C write failed (len=4)
Nov  4 09:02:48 debian kernel: [ 1594.488744] xc5000: xc_SetTVStandard failed
Nov  4 09:02:56 debian kernel: [ 1602.712774] xc5000: I2C write failed (len=4)
Nov  4 09:02:56 debian kernel: [ 1602.712782] xc5000: xc_SetTVStandard failed
Nov  4 09:03:05 debian kernel: [ 1611.000790] xc5000: I2C write failed (len=4)
Nov  4 09:03:05 debian kernel: [ 1611.000798] xc5000: xc_SetTVStandard failed
Nov  4 09:03:13 debian kernel: [ 1619.200774] xc5000: I2C write failed (len=4)
Nov  4 09:03:13 debian kernel: [ 1619.200782] xc5000: xc_SetTVStandard failed
Nov  4 09:03:21 debian kernel: [ 1627.508746] xc5000: I2C write failed (len=4)
Nov  4 09:03:21 debian kernel: [ 1627.508749] xc5000: xc_SetTVStandard failed
Nov  4 09:03:55 debian kernel: [ 1661.004759] xc5000: I2C write failed (len=4)
Nov  4 09:03:55 debian kernel: [ 1661.004767] xc5000: xc_SetTVStandard failed
Nov  4 09:04:03 debian kernel: [ 1669.220793] xc5000: I2C write failed (len=4)
Nov  4 09:04:03 debian kernel: [ 1669.220801] xc5000: xc_SetTVStandard failed
Nov  4 09:04:11 debian kernel: [ 1677.484755] xc5000: I2C write failed (len=4)
Nov  4 09:04:11 debian kernel: [ 1677.484763] xc5000: xc_SetTVStandard failed
Nov  4 09:04:36 debian kernel: [ 1702.236788] xc5000: I2C write failed (len=4)
Nov  4 09:04:36 debian kernel: [ 1702.236797] xc5000: xc_SetTVStandard failed
Nov  4 09:06:17 debian kernel: [   31.276177] xc5000: I2C read failed
Nov  4 09:06:17 debian kernel: [   31.276179] xc5000: xc_SetSignalSource(1) failed
Nov  4 09:06:17 debian kernel: [   31.276335] zl10353: write to reg 50 failed (err = -5)!
Nov  4 09:06:17 debian kernel: [   31.276479] zl10353: write to reg 50 failed (err = -5)!
Nov  4 09:06:17 debian kernel: [   36.261147] xc5000: I2C write failed (len=4)
Nov  4 09:06:17 debian kernel: [   36.261175] xc5000: I2C read failed
Nov  4 09:06:17 debian kernel: [   36.364588] xc5000: I2C write failed (len=4)
Nov  4 09:06:22 debian bluetoothd[1736]: Server initialization failed
Nov  4 09:06:32 debian kernel: [   57.101118] xc5000: I2C write failed (len=4)
Nov  4 09:06:32 debian kernel: [   57.101133] xc5000: I2C write failed (len=4)
Nov  4 09:06:32 debian kernel: [   57.101666] xc5000: I2C read failed
Nov  4 09:52:24 debian kernel: [   31.488209] xc5000: I2C read failed
Nov  4 09:52:24 debian kernel: [   31.488213] xc5000: xc_SetTVStandard failed
Nov  4 09:52:24 debian kernel: [   31.488372] zl10353: write to reg 50 failed (err = -5)!
Nov  4 09:52:24 debian kernel: [   31.488517] zl10353: write to reg 50 failed (err = -5)!
Nov  4 09:52:24 debian kernel: [   36.473150] xc5000: I2C write failed (len=4)
Nov  4 09:52:24 debian kernel: [   36.473176] xc5000: I2C read failed
Nov  4 09:52:24 debian kernel: [   36.576600] xc5000: I2C write failed (len=4)
Nov  4 09:52:28 debian bluetoothd[2265]: Server initialization failed
Nov  4 09:52:36 debian kernel: [  242.017149] xc5000: I2C write failed (len=4)
Nov  4 09:52:36 debian kernel: [  242.017177] xc5000: I2C write failed (len=4)
Nov  4 09:52:36 debian kernel: [  242.017900] xc5000: I2C read failed
Кто-нибудь с таким сталкивался, как решали? Помогите пожалуйста.



Последнее исправление: hikkikamori (всего исправлений: 2)
← [посоветуйте]Thinkpad E325 acpi-scripts
xen & nvidia - всё настолько безнадёжно ? →

В дополнение не могу найти свой тюнер из этого списка http://www.kernel.org/doc/Documentation/video4linux/CARDLIST.tuner

Если в /etc/modprobe.d/<...>.conf в options saa7134 ставить параметр tuner=<номер из вышеуказанного списка>, то ошибки нет, но тюнер ничего не показывает :(

hikkikamori
() автор топика

Кроме проблем с дровами, имей в виду, что непатченый tvtime не умеет пробрасывать звук с тюнера на выход, надо делать «arecord <с тюнера> | aplay <в систему>» с правильными ключами. Подробнее смотри на бехолдеровском форуме. Но, честно говоря, проще воткнуть комплектный шнурок для аппаратного проброса звука.

dmiceman ★★★★★
()
Ответ на: комментарий от dmiceman

> проще воткнуть комплектный шнурок для аппаратного проброса звука.

это с двумя 4-pin разъёмами? Одни в тюнер, а другой куда? В мать?

hikkikamori
() автор топика
Ответ на: комментарий от hikkikamori

это с двумя 4-pin разъёмами?

подловил. про H7 я ничего не знаю, у 590 есть просто звуковая дырка 3.5mm, от которой шнурок втыкается в line-in материнки.

dmiceman ★★★★★
()
Ответ на: комментарий от hikkikamori

Сидюк то тут не при чём. Aux и CD - так обычно называются звуковые входы на маме для подключения устройств внутри корпуса, на современных мамах такие уже не делают. Вариант - дискретная звуковушка.

fenris ★★★★★
()

поставил в параметр xc5000 - debug=1 вот куски dmesg: 

[    6.018747] Linux video capture interface: v2.00
[    6.258217] saa7130/34: v4l2 driver version 0.2.16 loaded
[    6.258461] saa7134 0000:02:07.0: PCI INT A -> GSI 22 (level, low) -> IRQ 22
[    6.258465] saa7133[0]: setting pci latency timer to 32
[    6.258470] saa7133[0]: found at 0000:02:07.0, rev: 209, irq: 22, latency: 32, mmio: 0xfbffb800
[    6.258476] saa7133[0]: subsystem: 5ace:7190, board: Beholder BeholdTV H7 [card=178,insmod option]
[    6.258539] saa7133[0]: board init: gpio is 0
[    6.280775] IR NEC protocol handler initialized
[    6.408045] saa7133[0]: i2c eeprom 00: ce 5a 90 71 54 20 00 00 00 00 00 00 00 00 00 01
[    6.408052] saa7133[0]: i2c eeprom 10: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
[    6.408057] saa7133[0]: i2c eeprom 20: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
[    6.408062] saa7133[0]: i2c eeprom 30: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
[    6.408067] saa7133[0]: i2c eeprom 40: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
[    6.408072] saa7133[0]: i2c eeprom 50: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
[    6.408077] saa7133[0]: i2c eeprom 60: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
[    6.408082] saa7133[0]: i2c eeprom 70: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
[    6.408087] saa7133[0]: i2c eeprom 80: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
[    6.408092] saa7133[0]: i2c eeprom 90: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
[    6.408098] saa7133[0]: i2c eeprom a0: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
[    6.408103] saa7133[0]: i2c eeprom b0: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
[    6.408108] saa7133[0]: i2c eeprom c0: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
[    6.408113] saa7133[0]: i2c eeprom d0: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
[    6.408118] saa7133[0]: i2c eeprom e0: d8 cf 00 00 ff ff ff ff ff ff ff ff ff ff ff ff
[    6.408123] saa7133[0]: i2c eeprom f0: 42 54 56 30 30 30 30 ff ff ff ff ff ff ff ff ff
[    6.416398] IR RC5(x) protocol handler initialized
......
[    6.856840] HDA Intel 0000:00:14.2: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[    6.869971] xc5000: xc5000_attach(1-0061)
[    6.869974] xc5000 1-0061: creating new instance
[    6.876060] xc5000: Successfully identified at address 0x61
[    6.876063] xc5000: Firmware has not been loaded previously
[    6.884187] xc5000: xc5000_is_firmware_loaded() returns True id = 0x20
[    6.884190] xc5000: xc5000_set_tv_freq() frequency=6400 (in units of 62.5khz)
[    6.884192] xc5000: xc_SetSignalSource(1) Source = CABLE
[    6.896600] nvidia: module license 'NVIDIA' taints kernel.
[    6.896602] Disabling lock debugging due to kernel taint
[    7.113762] lirc_dev: IR Remote Control driver registered, major 251 
[    7.123291] IR LIRC bridge handler initialized
.............
[    8.296331] input: HDA NVidia HDMI/DP as /devices/pci0000:00/0000:00:02.0/0000:04:00.1/sound/card1/input8
[    8.296378] input: HDA NVidia HDMI/DP as /devices/pci0000:00/0000:00:02.0/0000:04:00.1/sound/card1/input9
[    9.140057] xc5000: xc_SetTVStandard(0x8049,0x0c04)
[    9.140060] xc5000: xc_SetTVStandard() Standard = B/G-PAL-NICAM
[   15.164056] xc5000: xc_tune_channel(400000000)
[   15.164058] xc5000: xc_set_RF_frequency(400000000)
[   17.304062] xc5000: *** ADC envelope (0-1023) = 1798
[   17.312064] xc5000: *** Frequency error = 49796 Hz
[   17.320057] xc5000: *** Lock status (0-Wait, 1-Locked, 2-No-signal) = 27390
[   17.336057] xc5000: *** HW: V00.00, FW: V00.00.0000
[   17.344062] xc5000: *** Horizontal sync frequency = 7332 Hz
[   17.352066] xc5000: *** Frame lines = 50132
[   17.360056] xc5000: *** Quality (0:<8dB, 7:>56dB) = 0
[   17.368057] xc5000: xc5000_is_firmware_loaded() returns False id = 0x2000
[   17.376057] xc5000: xc5000_is_firmware_loaded() returns True id = 0x20
[   17.376059] xc5000: xc_initialize()
[   21.496059] xc5000: xc5000_set_tv_freq() frequency=6400 (in units of 62.5khz)
[   21.496062] xc5000: xc_SetSignalSource(1) Source = CABLE
[   23.504056] xc5000: xc_SetTVStandard(0x8049,0x0c04)
[   23.504059] xc5000: xc_SetTVStandard() Standard = B/G-PAL-NICAM
[   29.528056] xc5000: xc_tune_channel(400000000)
[   29.528059] xc5000: xc_set_RF_frequency(400000000)
[   31.668063] xc5000: *** ADC envelope (0-1023) = 1798
[   31.676062] xc5000: *** Frequency error = 805687 Hz
[   31.684064] xc5000: *** Lock status (0-Wait, 1-Locked, 2-No-signal) = 45568
[   31.700062] xc5000: *** HW: V00.00, FW: V00.00.0030
[   31.708062] xc5000: *** Horizontal sync frequency = 1976 Hz
[   31.716057] xc5000: *** Frame lines = 54527
[   31.724056] xc5000: *** Quality (0:<8dB, 7:>56dB) = 0
[   31.776043] Registered IR keymap rc-behold
[   31.776126] input: i2c IR (BeholdTV) as /devices/virtual/rc/rc0/input10
[   31.776173] rc0: i2c IR (BeholdTV) as /devices/virtual/rc/rc0
[   31.776175] ir-kbd-i2c: i2c IR (BeholdTV) detected at i2c-1/1-002d/ir0 [saa7133[0]]
[   31.776542] xc5000: xc5000_sleep()
[   31.776599] saa7133[0]: registered device video0 [v4l2]
[   31.776620] saa7133[0]: registered device vbi0
[   31.776636] saa7133[0]: registered device radio0
[   31.796052] xc5000: xc5000_is_firmware_loaded() returns False id = 0x2000
[   31.804069] xc5000: xc5000_is_firmware_loaded() returns True id = 0x20
[   31.804072] xc5000: xc5000_set_radio_freq() frequency=1400000 (in units of khz)
[   31.804074] xc5000: xc5000_set_radio_freq() radio input not configured
[   31.804125] xc5000: xc5000_sleep()
[   31.812056] xc5000: xc5000_is_firmware_loaded() returns False id = 0x2000
[   31.817918] dvb_init() allocating 1 frontend
[   31.820066] xc5000: xc5000_is_firmware_loaded() returns True id = 0x20
[   31.820069] xc5000: xc_initialize()
[   31.828063] xc5000: xc5000_is_firmware_loaded() returns False id = 0x2000
[   31.828066] xc5000: waiting for firmware upload (dvb-fe-xc5000-1.6.114.fw)...
[   31.829149] xc5000: I2C write failed (len=4)
[   31.829177] zl10353_read_register: readreg error (reg=127, ret==-5)
[   31.829184] saa7133[0]/dvb: frontend initialization failed
[   31.868738] saa7134 ALSA driver for DMA sound loaded
[   31.868764] saa7133[0]/alsa: saa7133[0] at 0xfbffb800 irq 22 registered as card -1
[   31.871588] xc5000: firmware read 12401 bytes.
[   31.871590] xc5000: firmware uploading...
[   31.871592] xc5000: xc5000_TunerReset()
[   34.368051] xc5000: Unable to load firmware and init tuner
[   34.368178] xc5000: xc5000_sleep()
[   36.016058] xc5000: firmware upload complete...
[   36.016068] xc5000: xc_initialize()
[   36.212058] xc5000: xc5000_set_tv_freq() frequency=6400 (in units of 62.5khz)
[   36.212061] xc5000: xc_SetSignalSource(1) Source = CABLE
[   36.228064] xc5000: xc_SetTVStandard(0x8049,0x0c04)
[   36.228067] xc5000: xc_SetTVStandard() Standard = B/G-PAL-NICAM
[   36.276064] xc5000: xc_tune_channel(400000000)
[   36.276066] xc5000: xc_set_RF_frequency(400000000)
[   36.844063] xc5000: *** ADC envelope (0-1023) = 956
[   36.852057] xc5000: *** Frequency error = 0 Hz
[   36.860057] xc5000: *** Lock status (0-Wait, 1-Locked, 2-No-signal) = 2
[   36.876064] xc5000: *** HW: V03.02, FW: V01.06.0072
[   36.884065] xc5000: *** Horizontal sync frequency = 15931 Hz
[   36.892057] xc5000: *** Frame lines = 65535
[   36.900056] xc5000: *** Quality (0:<8dB, 7:>56dB) = 0
[   36.900164] xc5000: xc5000_sleep()

hikkikamori
() автор топика
Ответ на: комментарий от hikkikamori

продолжение 

....................
[   58.276026] xc5000: xc5000_is_firmware_loaded() returns True id = 0x1388
[   58.276030] xc5000: xc5000_set_radio_freq() frequency=1400000 (in units of khz)
[   58.276032] xc5000: xc5000_set_radio_freq() radio input not configured
[   58.276563] xc5000: xc5000_sleep()
[   58.284067] xc5000: xc5000_is_firmware_loaded() returns True id = 0x1388
[   58.284071] xc5000: xc5000_set_tv_freq() frequency=6400 (in units of 62.5khz)
[   58.284073] xc5000: xc_SetSignalSource(1) Source = CABLE
[   58.292071] xc5000: xc5000_is_firmware_loaded() returns True id = 0x1388
[   58.292075] xc5000: xc5000_set_tv_freq() frequency=6400 (in units of 62.5khz)
[   58.292077] xc5000: xc_SetSignalSource(1) Source = CABLE
[   58.316072] xc5000: xc_SetTVStandard(0x8049,0x0c04)
[   58.316074] xc5000: xc_SetTVStandard() Standard = B/G-PAL-NICAM
[   58.324057] xc5000: xc_SetTVStandard(0x8049,0x0c04)
[   58.324060] xc5000: xc_SetTVStandard() Standard = B/G-PAL-NICAM
[   58.412056] xc5000: xc_tune_channel(400000000)
[   58.412059] xc5000: xc_set_RF_frequency(400000000)
[   58.420048] xc5000: xc_tune_channel(400000000)
[   58.420051] xc5000: xc_set_RF_frequency(400000000)
[   58.433152] xc5000: I2C write failed (len=4)
[   58.433177] xc5000: I2C read failed
[   58.544046] xc5000: *** ADC envelope (0-1023) = 108
[   58.552066] xc5000: *** ADC envelope (0-1023) = 88
[   58.560055] xc5000: *** Frequency error = 0 Hz
[   58.568069] xc5000: *** Frequency error = 0 Hz
[   58.576055] xc5000: *** Lock status (0-Wait, 1-Locked, 2-No-signal) = 0
[   58.584047] xc5000: *** Lock status (0-Wait, 1-Locked, 2-No-signal) = 0
[   58.608065] xc5000: *** HW: V03.02, FW: V01.06.0072
[   58.616055] xc5000: *** HW: V03.02, FW: V01.06.0072
[   58.624059] xc5000: *** Horizontal sync frequency = 16206 Hz
[   58.632051] xc5000: *** Horizontal sync frequency = 16076 Hz
[   58.640063] xc5000: *** Frame lines = 65535
[   58.648055] xc5000: *** Frame lines = 689
[   58.656061] xc5000: *** Quality (0:<8dB, 7:>56dB) = 5
[   58.664051] xc5000: *** Quality (0:<8dB, 7:>56dB) = 1
[   59.787472] xc5000: xc5000_sleep()
[   59.787857] xc5000: xc5000_sleep()

hikkikamori
() автор топика
Ответ на: комментарий от hikkikamori

С этим скриптом звук появился: 

hikkikamori@debian:~$ cat ./tv-time.sh
#!/bin/sh
sox -q -c 2 -s -r 32000 -t ossdsp /dev/dsp2 -t ossdsp -r 32000 /dev/dsp &
soxpid=$!
sleep 0.5
tvtime
kill $soxpid

hikkikamori
() автор топика
Вы не можете добавлять комментарии в эту тему. Тема перемещена в архив.
← [посоветуйте]Thinkpad E325 acpi-scripts
Linux-hardware
xen & nvidia - всё настолько безнадёжно ? →