не могу разобраться с hdparm

Возможно желзка не расчитана на это. валожи результаты hdparm -I /dev/hdc , то же и для другого диска и lspci -v

Не ну по отдельности-то каждый работает... а вместе ни в какую. За три раза выложу а то тут сообщение слишком большое выходит.

/dev/hdc:

ATA device, with non-removable media Model Number: MAXTOR 6L040J2 Serial Number: 662214007797 Firmware Revision: AR1.0500 Standards: Used: ATA/ATAPI-5 T13 1321D revision 1 Supported: 5 4 3 2 & some of 6 Configuration: Logical max current cylinders 16383 16383 heads 16 16 sectors/track 63 63 -- CHS current addressable sectors: 16514064 LBA user addressable sectors: 78177792 device size with M = 1024*1024: 38172 MBytes device size with M = 1000*1000: 40027 MBytes (40 GB) Capabilities: LBA, IORDY(can be disabled) bytes avail on r/w long: 4 Queue depth: 1 Standby timer values: spec'd by Vendor, no device specific minimum R/W multiple sector transfer: Max = 16 Current = 16 Recommended acoustic management value: 128, current value: 254 DMA: mdma0 mdma1 mdma2 udma0 udma1 udma2 udma3 *udma4 udma5 udma6 Cycle time: min=120ns recommended=120ns PIO: pio0 pio1 pio2 pio3 pio4 Cycle time: no flow control=120ns IORDY flow control=120ns Commands/features: Enabled Supported: * READ BUFFER cmd * WRITE BUFFER cmd * Host Protected Area feature set * Look-ahead * Write cache * Power Management feature set Security Mode feature set SMART feature set * Mandatory FLUSH CACHE command * Device Configuration Overlay feature set * Automatic Acoustic Management feature set SET MAX security extension * DOWNLOAD MICROCODE cmd * SMART self-test * SMART error logging Security: Master password revision code = 65534 supported not enabled not locked not frozen not expired: security count not supported: enhanced erase 20min for SECURITY ERASE UNIT. HW reset results: CBLID- above Vih Device num = 0 determined by the jumper Checksum: correct

hdparm -I /dev/hdd

/dev/hdd:

ATA device, with non-removable media
powers-up in standby; SET FEATURES subcmd spins-up.
Model Number: IC35L120AVV207-0
Serial Number: VNVD06G4H0ZPHL
Firmware Revision: V24OA66A
Standards:
Used: ATA/ATAPI-6 T13 1410D revision 3a
Supported: 6 5 4 3
Configuration:
Logical max current
cylinders 16383 65535
heads 15 1
sectors/track 63 63
--
CHS current addressable sectors: 4128705
LBA user addressable sectors: 241254720
LBA48 user addressable sectors: 241254720
device size with M = 1024*1024: 117800 MBytes
device size with M = 1000*1000: 123522 MBytes (123 GB)
Capabilities:
LBA, IORDY(can be disabled)
bytes avail on r/w long: 52 Queue depth: 32
Standby timer values: spec'd by Standard, no device specific minimum
R/W multiple sector transfer: Max = 16 Current = 16
Advanced power management level: unknown setting (0x0000)
Recommended acoustic management value: 128, current value: 254
DMA: mdma0 mdma1 mdma2 udma0 udma1 udma2 udma3 udma4 *udma5
Cycle time: min=120ns recommended=120ns
PIO: pio0 pio1 pio2 pio3 pio4
Cycle time: no flow control=240ns IORDY flow control=120ns
Commands/features:
Enabled Supported:
* NOP cmd
* READ BUFFER cmd
* WRITE BUFFER cmd
* Host Protected Area feature set
Release interrupt
* Look-ahead
* Write cache
* Power Management feature set
Security Mode feature set
SMART feature set
* FLUSH CACHE EXT command
* Mandatory FLUSH CACHE command
* Device Configuration Overlay feature set
* 48-bit Address feature set
* Automatic Acoustic Management feature set
SET MAX security extension
Address Offset Reserved Area Boot
SET FEATURES subcommand required to spinup after power up
Power-Up In Standby feature set
Advanced Power Management feature set
* READ/WRITE DMA QUEUED
* General Purpose Logging feature set
* SMART self-test
* SMART error logging
Security:
Master password revision code = 65534
supported
not enabled
not locked
not frozen
not expired: security count
not supported: enhanced erase
60min for SECURITY ERASE UNIT.
HW reset results:
CBLID- above Vih
Device num = 1 determined by the jumper
Checksum: correct

lspci -v
00:00.0 Host bridge: Silicon Integrated Systems [SiS] 650/M650 Host (rev 01)
Subsystem: Silicon Integrated Systems [SiS] 650/M650 Host
Flags: bus master, medium devsel, latency 32
Memory at e0000000 (32-bit, non-prefetchable) [size=64M]
Capabilities: [c0] AGP version 2.0

00:01.0 PCI bridge: Silicon Integrated Systems [SiS] Virtual PCI-to-PCI bridge (AGP) (prog-if 00 [Normal decode])
Flags: bus master, fast devsel, latency 64
Bus: primary=00, secondary=01, subordinate=01, sec-latency=32
Memory behind bridge: c8000000-c9ffffff
Prefetchable memory behind bridge: c4000000-c7ffffff

00:02.0 ISA bridge: Silicon Integrated Systems [SiS] SiS961 [MuTIOL Media IO]
Flags: bus master, medium devsel, latency 0

00:02.1 SMBus: Silicon Integrated Systems [SiS] SiS961/2 SMBus Controller
Flags: medium devsel, IRQ 21
I/O ports at 1080 [size=32]

00:02.2 USB Controller: Silicon Integrated Systems [SiS] USB 1.0 Controller (rev 07) (prog-if 10 [OHCI])
Subsystem: Silicon Integrated Systems [SiS] USB 1.0 Controller
Flags: bus master, medium devsel, latency 32, IRQ 20
Memory at ca000000 (32-bit, non-prefetchable) [size=4K]

00:02.3 USB Controller: Silicon Integrated Systems [SiS] USB 1.0 Controller (rev 07) (prog-if 10 [OHCI])
Subsystem: Silicon Integrated Systems [SiS] USB 1.0 Controller
Flags: bus master, medium devsel, latency 32, IRQ 23
Memory at ca001000 (32-bit, non-prefetchable) [size=4K]

00:02.5 IDE interface: Silicon Integrated Systems [SiS] 5513 [IDE] (rev d0) (prog-if 80 [Master])
Subsystem: Silicon Integrated Systems [SiS] SiS5513 EIDE Controller (A,B step)
Flags: bus master, fast devsel, latency 128
I/O ports at 4000 [size=16]

00:02.7 Multimedia audio controller: Silicon Integrated Systems [SiS] Sound Controller (rev a0)
Subsystem: Micro-Star International Co., Ltd.: Unknown device 5330
Flags: bus master, medium devsel, latency 32, IRQ 21
I/O ports at d800 [size=256]
I/O ports at dc00 [size=128]
Capabilities: [48] Power Management version 2

00:07.0 Modem: PCTel Inc HSP MicroModem 56 (rev 02) (prog-if 04 [Hayes/16750])
Subsystem: PCTel Inc: Unknown device 0001
Flags: medium devsel, IRQ 18
I/O ports at e000 [size=64]
Capabilities: [40] Power Management version 2

00:08.0 Multimedia video controller: Brooktree Corporation Bt878 Video Capture (rev 11)
Subsystem: Avermedia Technologies Inc: Unknown device 0003
Flags: bus master, medium devsel, latency 32, IRQ 19
Memory at ca002000 (32-bit, prefetchable) [size=4K]
Capabilities: [44] Vital Product Data
Capabilities: [4c] Power Management version 2

00:08.1 Multimedia controller: Brooktree Corporation Bt878 Audio Capture (rev 11)
Subsystem: Avermedia Technologies Inc: Unknown device 0003
Flags: bus master, medium devsel, latency 32, IRQ 19
Memory at ca003000 (32-bit, prefetchable) [size=4K]
Capabilities: [44] Vital Product Data
Capabilities: [4c] Power Management version 2

01:00.0 VGA compatible controller: nVidia Corporation NV18 [GeForce4 MX 440 AGP 8x] (rev a4) (prog-if 00 [VGA])
Flags: bus master, 66Mhz, medium devsel, latency 248, IRQ 16
Memory at c8000000 (32-bit, non-prefetchable) [size=16M]
Memory at c4000000 (32-bit, prefetchable) [size=64M]
Expansion ROM at <unassigned> [disabled] [size=128K]
Capabilities: [60] Power Management version 2
Capabilities: [44] AGP version 3.0

С этим чипом похожая проблемма уже была http://bugzilla.kernel.org/show_bug.cgi?id=3511 .С ядром 2.4.х у тебя наврятли не что ниполучится, глянь в ядре CONFIG_IDEDMA_PCI_AUTO и если отключено то включи.

Еще кое что. У тебя чип позволяет выдать максимум Ultra 100 (udma5). Проблема в том что я не знаю может ли потянуть Ultra 100 два по udma5 на одном шлейфе. А У тя один винч позволяет 5 а друго 6

Если читаешь по английски. Remember that in order to use UDMA4 (and above) mode you have to use a special 80 conductor cable, and the driver tries to determine if you have such a cable attached before setting UDMA4 mode. У тебя есть такой кабель????