википедию читал, наверно все должно быть окейна. но я просто не разбираюсь в железе и могу ошибаться ._.
# smartctl --all /dev/sda
smartctl 5.43 2012-06-30 r3573 [x86_64-linux-3.8.2] (local build)
Copyright (C) 2002-12 by Bruce Allen, http://smartmontools.sourceforge.net
=== START OF INFORMATION SECTION ===
Model Family: Western Digital Scorpio Blue Serial ATA (Adv. Format)
Device Model: WDC WD3200BPVT-22JJ5T0
Serial Number: WD-WXU1E13YXCU2
LU WWN Device Id: 5 0014ee 60350da7c
Firmware Version: 01.01A01
User Capacity: 320,072,933,376 bytes [320 GB]
Sector Sizes: 512 bytes logical, 4096 bytes physical
Device is: In smartctl database [for details use: -P show]
ATA Version is: 8
ATA Standard is: Exact ATA specification draft version not indicated
Local Time is: Thu Aug 22 23:09:44 2013 GMT
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x00) Offline data collection activity
was never started.
Auto Offline Data Collection: Disabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: ( 7080) seconds.
Offline data collection
capabilities: (0x7b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 73) minutes.
Conveyance self-test routine
recommended polling time: ( 5) minutes.
SCT capabilities: (0x7035) SCT Status supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x002f 200 200 051 Pre-fail Always - 0
3 Spin_Up_Time 0x0027 144 137 021 Pre-fail Always - 1775
4 Start_Stop_Count 0x0032 100 100 000 Old_age Always - 317
5 Reallocated_Sector_Ct 0x0033 200 200 140 Pre-fail Always - 0
7 Seek_Error_Rate 0x002e 200 200 000 Old_age Always - 0
9 Power_On_Hours 0x0032 100 100 000 Old_age Always - 18
10 Spin_Retry_Count 0x0032 100 100 000 Old_age Always - 0
11 Calibration_Retry_Count 0x0032 100 100 000 Old_age Always - 0
12 Power_Cycle_Count 0x0032 100 100 000 Old_age Always - 160
191 G-Sense_Error_Rate 0x0032 062 062 000 Old_age Always - 38
192 Power-Off_Retract_Count 0x0032 200 200 000 Old_age Always - 105
193 Load_Cycle_Count 0x0032 200 200 000 Old_age Always - 1430
194 Temperature_Celsius 0x0022 113 098 000 Old_age Always - 30
196 Reallocated_Event_Count 0x0032 200 200 000 Old_age Always - 0
197 Current_Pending_Sector 0x0032 200 200 000 Old_age Always - 0
198 Offline_Uncorrectable 0x0030 100 253 000 Old_age Offline - 0
199 UDMA_CRC_Error_Count 0x0032 200 200 000 Old_age Always - 0
200 Multi_Zone_Error_Rate 0x0008 100 253 000 Old_age Offline - 0
SMART Error Log Version: 1
No Errors Logged
SMART Self-test log structure revision number 1
No self-tests have been logged. [To run self-tests, use: smartctl -t]
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.апосля сборки ядра, lm_sensors
# sensors
acpitz-virtual-0
Adapter: Virtual device
temp1: +43.0°C (crit = +100.0°C)
coretemp-isa-0000
Adapter: ISA adapter
Physical id 0: +42.0°C (high = +87.0°C, crit = +105.0°C)
Core 0: +40.0°C (high = +87.0°C, crit = +105.0°C)
Core 1: +39.0°C (high = +87.0°C, crit = +105.0°C)и тут тоже ок?
и подскажите, на что еще посмотреть.
кстати, спасибо товарищу который посоветовал slax - дистрибутив пушка! 95% нужного уже есть из коробки, а того что нет (wine, dosbox), скачалось и скопировалось «модулями» с офф. сайта тремя файликами. схоронил его на флешку, загружаю в память, флешку вытаскиваю. в итоге, ни флешка, ни винт не используются на ноутбуке. памяти расходуется всего 400мб - это кеды с огнелисом, сам офигнел.
после должной настройки и выпиливания ненужнокед добьюсь своих 200мб, а остальную память буду использовать под tmpfs.
