JMicron, SATA2 и прочая х...!

Федорку 7-ю впихни.

> Федорку 7-ю впихни.

Думаешь встанет ? Есть подозрения, что последняя Mandriva еще может на такое железо поставиться...хотя хз.

all-generic-ide

> all-generic-ide

Dimez, спасибо, почти помогло :) Терь гента виснит на шаге монтирования /dev/hda[c] . Убунту поставить удалось на второй жесткий диск, однако никак не удается настроить её на нормальный boot (аля Grub) вместе с Windows (всякие эррор типа повреждены файлы винды или /bin/sh: can't access tty || failed to set xfermode)

Вообщем моя плакаль, винду мать её как-то ведь оставить надо ....

генту лайф сиди не пойдет,да и надо ли там все ручками ставить надо потому что-то вроде gentoo minimal install cd.у мну из за джимикрона такое было тоже

У меня MB Abit P9 pro то же искал дистрибутив, который поймет JMicron, без проблем встала SUSE 10.2

слака 11я

If you have a Core 2 Duo-capable motherboard and are getting an error message about the installer not being able to find the CD/DVD after you have already booted from it, the problem is likely with your IDE controller. In some modern motherboards, the parallel ATA controller has been taken out of the chipset and moved to a third-party drive controller. That third party is JMicron, and this problem most famously occurs in the Asus P5B motherboard, though other brands and models can be affected as well. First, it will help to do a quick workaround in your BIOS. Press the Del, F1, or F2 key to get into your system BIOS just after powering it on. There should be a message somewhere on the screen that tells you which key to press; if you are not sure, press all three repeatedly and you're sure to get there. Somewhere in the BIOS setup you should see an option for the JMicron drive controller ("Onboard Devices" in the P5B BIOS menu). Set it to AHCI mode, then save and exit the BIOS setup utility. Boot from the openSUSE 10.2 CD 1 or DVD. You'll still get the same message, but now you're better enabled to work around it. Press Enter to get past the error message, then choose your language in the following screen. That will bring you to the main menu. Use the down arrow key to select the Kernel Modules option and press Enter. In the next screen press Enter again to select the default option for IDE/RAID/SCSI Modules. In the long list that follows, find both the JMicron and the Generic IDE drivers, select them, press Enter, then press Enter again when you're asked for special options to pass to them. You will have to do this twice -- one time for each driver. When you return to the kernel module screen, use the Tab or arrow keys to select Back, and press Enter. That should put you back into the Main Menu. Now select the option for Start Installation or System and press Enter, then select Start Installation or Update and press Enter, and lastly select the CD-ROM as the source and press Enter. The normal graphical installation procedure will commence. If the above does not work, write down installation source mirror addresses from the link in the installation source section below and use them to install openSUSE over FTP. The only difference in the procedure will be to change the above instructions to select FTP instead of CD-ROM as the source.

http://www.softwareinreview.com/cms/content/view/60/

HTH

А забыл, сори, я еше обновил биос, и все заработало (кстати после обновления плата не запускалась дето час, я побежал к другу за дисководом, пока бегал она сама вдруг стала работать гг, шо за чес хз)