Не могу перейти в консоль, гаснет монитор :(

Вообщем настроил двойные Х-ы на монитор и на телек, вообщем всё 
прикольно, теперь мона что то делать на компе и одновременно смотреть
фильм в полноэкранном режиме на телеке. Но есть одна проблема, не 
могу из Х-ов перелезть в консоль по Ctrl+Alt+F1, экран при этом гаснет и 
переходит в стенд бай, но система не виснет, т.е. если после этого нажать 
Alt+F7 то экран загорается и всё пучком. Может кто знает как это 
пофиксить.

Вот кусок конфига:

--------------------------------------------------------------------------------

# **********************************************************************
# Monitor section
# **********************************************************************

# Any number of monitor sections may be present

Section "Monitor"

   Identifier  "Monitor"

# HorizSync is in kHz unless units are specified.
# HorizSync may be a comma separated list of discrete values, or a
# comma separated list of ranges of values.
# NOTE: THE VALUES HERE ARE EXAMPLES ONLY.  REFER TO YOUR MONITOR'S
# USER MANUAL FOR THE CORRECT NUMBERS.

   HorizSync   30-99.9
   
#    HorizSync   30-64         # multisync
#    HorizSync   31.5, 35.2    # multiple fixed sync frequencies
#    HorizSync   15-25, 30-50  # multiple ranges of sync frequencies

# VertRefresh is in Hz unless units are specified.
# VertRefresh may be a comma separated list of discrete values, or a
# comma separated list of ranges of values.
# NOTE: THE VALUES HERE ARE EXAMPLES ONLY.  REFER TO YOUR MONITOR'S
# USER MANUAL FOR THE CORRECT NUMBERS.

   VertRefresh 85-160

EndSection

Section "Monitor"

   Identifier  "TV"
   HorizSync   10-99.9
   VertRefresh 50-60

EndSection

# **********************************************************************
# Graphics device section
# **********************************************************************

Section "Device"

   Identifier  "nvidia-crt"
   BusID       "PCI:1:0:0"
   Driver      "nvidia"
   VideoRam    131072
   Screen   0
   
   Option   "ConnectedMonitor"   "CRT-1"
   Option   "RenderAccel" "true"
   Option   "CursorShadow" "1"

#   Insert Clocks lines here if appropriate
   
   Option       "OverlayDefaultVisual" "true"
   Option       "CIOverlay" "true"
   Option       "Overlay" "true"
   Option       "RenderAccel" "true"
   Option       "NoLogo" "true"
   Option       "NvAGP" "3"

EndSection

Section "Device"
   
   Identifier  "nvidia-tv"
   BusID       "PCI:1:0:0"
   Driver      "nvidia"
   Screen   1
   
   Option   "ConnectedMonitor"   "TV-0"
   Option   "TVStandard"   "PAL-G"
   Option   "TVOutFormat"   "COMPOSITE"

#   Insert Clocks lines here if appropriate

EndSection

Section "Extensions"
   
   Option "Composite"   "true"
   Option "RENDER"   "true"

EndSection

# **********************************************************************
# Screen sections
# **********************************************************************

# Any number of screen sections may be present.  Each describes
# the configuration of a single screen.  A single specific screen section
# may be specified from the X server command line with the "-screen"
# option.


Section "Screen"

   Identifier  "CRT Screen"
   Device      "nvidia-crt"
   Monitor     "Monitor"
   DefaultDepth 24
   
   Subsection "Display"

      Depth       24
      Modes       "1280x1024" "800x600" "640x480"
      ViewPort    0 0

   EndSubsection

EndSection

Section "Screen"
   
   Identifier "TV Screen"
   Device   "nvidia-tv"
   Monitor   "TV"
   DefaultDepth 24
   
   Subsection "Display"
   
      Depth 24
      Modes "800x600"
      ViewPort 0 0

   EndSubsection

# **********************************************************************
# ServerLayout sections.
# **********************************************************************

# Any number of ServerLayout sections may be present.  Each describes
# the way multiple screens are organised.  A specific ServerLayout
# section may be specified from the X server command line with the
# "-layout" option.  In the absence of this, the first section is used.
# When now ServerLayout section is present, the first Screen section
# is used alone.

Section "ServerLayout"

# The Identifier line must be present
    Identifier  "Simple Layout"

# Each Screen line specifies a Screen section name, and optionally
# the relative position of other screens.  The four names after
# primary screen name are the screens to the top, bottom, left and right
# of the primary screen.  In this example, screen 2 is located to the
# right of screen 1.

#    Screen "Screen 1"
    Screen 0 "CRT Screen"
    Screen 1 "TV Screen" rightOf "CRT Screen"

# Each InputDevice line specifies an InputDevice section name and
# optionally some options to specify the way the device is to be
# used.  Those options include "CorePointer", "CoreKeyboard" and
# "SendCoreEvents".

    InputDevice "Mouse1" "CorePointer"
    InputDevice "Keyboard1" "CoreKeyboard"

EndSection

# Section "DRI"
#    Mode 0666
# EndSection 

--------------------------------------------------------------------------------


Заранее спасибо!!!