LINUX.ORG.RU
Форум — Linux-hardware  

Проблемы с ЖД


0

0

Винт начал издавать странные звуки, как-будто читает что-то, но не может прочесть и начинает заново, и так по несколько серий с небольшими перерывами между каждой попыткой и перерывами побольше между сериями. Такое было при установке винды года 2 назад, тогда носил его по гарантии, там его проверили - всё чисто. Потом поставил Линукс и больше такого не было, до сих пор. На время этой странной операции все команды, связанные с чтением с ЖД блокируются. Смотрел smartctl, все параметры в норме (в WHEN_FAILED - прочерк), но после них есть сообщения об ошибках.

Вот думаю теперь, посыпется или нет? mhdd не смотрел.

★★★★★
← Свеженькая кубунта
Выбор ноутбука: 25000-28000р. →
Ответ на: комментарий от anatol

Нет, у меня via kt-880 (или как его там). Вобщем, я думаю пока всё в порядке.

seiken ★★★★★
() автор топика
Ответ на: комментарий от anonymous 

Не думал, что кто-то ещё ответит сюда. И тем не менее:


smartctl version 5.34 [i686-pc-linux-gnu] Copyright (C) 2002-5 Bruce Allen
Home page is http://smartmontools.sourceforge.net/

=== START OF INFORMATION SECTION ===
Model Family:     Hitachi Deskstar 7K250 series
Device Model:     HDS722516VLAT80
Serial Number:    VNR43EC4CHVJJM
Firmware Version: V34OA63A
User Capacity:    164 696 555 520 bytes
Device is:        In smartctl database [for details use: -P show]
ATA Version is:   6
ATA Standard is:  ATA/ATAPI-6 T13 1410D revision 3a
Local Time is:    Sun Apr 29 21:55:56 2007 MSD
SMART support is: Available - device has SMART capability.
SMART support is: Disabled

=== START OF ENABLE/DISABLE COMMANDS SECTION ===
SMART Enabled.

=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED

General SMART Values:
Offline data collection status:  (0x00)	Offline data collection activity
					was never started.
					Auto Offline Data Collection: Disabled.
Self-test execution status:      (   0)	The previous self-test routine completed
					without error or no self-test has ever 
					been run.
Total time to complete Offline 
data collection: 		 (3585) seconds.
Offline data collection
capabilities: 			 (0x1b) SMART execute Offline immediate.
					Auto Offline data collection on/off support.
					Suspend Offline collection upon new
					command.
					Offline surface scan supported.
					Self-test supported.
					No Conveyance Self-test supported.
					No Selective Self-test supported.
SMART capabilities:            (0x0003)	Saves SMART data before entering
					power-saving mode.
					Supports SMART auto save timer.
Error logging capability:        (0x01)	Error logging supported.
					General Purpose Logging supported.
Short self-test routine 
recommended polling time: 	 (   1) minutes.
Extended self-test routine
recommended polling time: 	 (  60) minutes.

SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME          FLAG     VALUE WORST THRESH TYPE      UPDATED  WHEN_FAILED RAW_VALUE
  1 Raw_Read_Error_Rate     0x000b   093   093   060    Pre-fail  Always       -       2359296
  2 Throughput_Performance  0x0005   100   100   050    Pre-fail  Offline      -       0
  3 Spin_Up_Time            0x0007   216   216   024    Pre-fail  Always       -       139 (Average 138)
  4 Start_Stop_Count        0x0012   100   100   000    Old_age   Always       -       1664
  5 Reallocated_Sector_Ct   0x0033   100   100   005    Pre-fail  Always       -       47
  7 Seek_Error_Rate         0x000b   100   100   067    Pre-fail  Always       -       0
  8 Seek_Time_Performance   0x0005   100   100   020    Pre-fail  Offline      -       0
  9 Power_On_Hours          0x0012   099   099   000    Old_age   Always       -       12022
 10 Spin_Retry_Count        0x0013   100   100   060    Pre-fail  Always       -       0
 12 Power_Cycle_Count       0x0032   100   100   000    Old_age   Always       -       1431
192 Power-Off_Retract_Count 0x0032   099   099   050    Old_age   Always       -       2179
193 Load_Cycle_Count        0x0012   099   099   050    Old_age   Always       -       2179
194 Temperature_Celsius     0x0002   134   134   000    Old_age   Always       -       41 (Lifetime Min/Max 17/50)
196 Reallocated_Event_Count 0x0032   100   100   000    Old_age   Always       -       110
197 Current_Pending_Sector  0x0022   100   100   000    Old_age   Always       -       1
198 Offline_Uncorrectable   0x0008   100   100   000    Old_age   Offline      -       0
199 UDMA_CRC_Error_Count    0x000a   200   200   000    Old_age   Always       -       0

seiken ★★★★★
() автор топика
Ответ на: комментарий от seiken 

SMART Error Log Version: 1
ATA Error Count: 662 (device log contains only the most recent five errors)
	CR = Command Register [HEX]
	FR = Features Register [HEX]
	SC = Sector Count Register [HEX]
	SN = Sector Number Register [HEX]
	CL = Cylinder Low Register [HEX]
	CH = Cylinder High Register [HEX]
	DH = Device/Head Register [HEX]
	DC = Device Command Register [HEX]
	ER = Error register [HEX]
	ST = Status register [HEX]
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.

Error 662 occurred at disk power-on lifetime: 12019 hours (500 days + 19 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER ST SC SN CL CH DH
  -- -- -- -- -- -- --
  40 51 03 53 30 be f3  Error: UNC 3 sectors at LBA = 0x03be3053 = 62795859

  Commands leading to the command that caused the error were:
  CR FR SC SN CL CH DH DC   Powered_Up_Time  Command/Feature_Name
  -- -- -- -- -- -- -- --  ----------------  --------------------
  25 00 08 4e 30 be f0 00      01:53:21.400  READ DMA EXT
  25 00 08 4e 30 be f0 00      01:53:16.200  READ DMA EXT
  25 00 08 46 30 be f0 00      01:53:16.200  READ DMA EXT
  25 00 08 3e 30 be f0 00      01:53:16.200  READ DMA EXT
  25 00 08 36 30 be f0 00      01:53:16.200  READ DMA EXT

Error 661 occurred at disk power-on lifetime: 12019 hours (500 days + 19 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER ST SC SN CL CH DH
  -- -- -- -- -- -- --
  40 51 03 53 30 be f3  Error: UNC 3 sectors at LBA = 0x03be3053 = 62795859

  Commands leading to the command that caused the error were:
  CR FR SC SN CL CH DH DC   Powered_Up_Time  Command/Feature_Name
  -- -- -- -- -- -- -- --  ----------------  --------------------
  25 00 08 4e 30 be f0 00      01:53:16.200  READ DMA EXT
  25 00 08 46 30 be f0 00      01:53:16.200  READ DMA EXT
  25 00 08 3e 30 be f0 00      01:53:16.200  READ DMA EXT
  25 00 08 36 30 be f0 00      01:53:16.200  READ DMA EXT
  25 00 08 2e 30 be f0 00      01:53:16.200  READ DMA EXT

Error 660 occurred at disk power-on lifetime: 12019 hours (500 days + 19 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER ST SC SN CL CH DH
  -- -- -- -- -- -- --
  40 51 83 53 30 be f3  Error: UNC 131 sectors at LBA = 0x03be3053 = 62795859

  Commands leading to the command that caused the error were:
  CR FR SC SN CL CH DH DC   Powered_Up_Time  Command/Feature_Name
  -- -- -- -- -- -- -- --  ----------------  --------------------
  25 00 88 4e 30 be f0 00      01:53:10.400  READ DMA EXT
  25 00 90 46 30 be f0 00      01:53:05.200  READ DMA EXT
  25 00 98 3e 30 be f0 00      01:53:00.000  READ DMA EXT
  25 00 a0 36 30 be f0 00      01:52:54.900  READ DMA EXT
  25 00 a8 2e 30 be f0 00      01:52:49.800  READ DMA EXT

Error 659 occurred at disk power-on lifetime: 12019 hours (500 days + 19 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER ST SC SN CL CH DH
  -- -- -- -- -- -- --
  40 51 83 53 30 be f3  Error: UNC 131 sectors at LBA = 0x03be3053 = 62795859

  Commands leading to the command that caused the error were:
  CR FR SC SN CL CH DH DC   Powered_Up_Time  Command/Feature_Name
  -- -- -- -- -- -- -- --  ----------------  --------------------
  25 00 90 46 30 be f0 00      01:53:05.200  READ DMA EXT
  25 00 98 3e 30 be f0 00      01:53:00.000  READ DMA EXT
  25 00 a0 36 30 be f0 00      01:52:54.900  READ DMA EXT
  25 00 a8 2e 30 be f0 00      01:52:49.800  READ DMA EXT
  25 00 b0 26 30 be f0 00      01:52:44.600  READ DMA EXT

Error 658 occurred at disk power-on lifetime: 12019 hours (500 days + 19 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER ST SC SN CL CH DH
  -- -- -- -- -- -- --
  40 51 83 53 30 be f3  Error: UNC 131 sectors at LBA = 0x03be3053 = 62795859

  Commands leading to the command that caused the error were:
  CR FR SC SN CL CH DH DC   Powered_Up_Time  Command/Feature_Name
  -- -- -- -- -- -- -- --  ----------------  --------------------
  25 00 98 3e 30 be f0 00      01:53:00.000  READ DMA EXT
  25 00 a0 36 30 be f0 00      01:52:54.900  READ DMA EXT
  25 00 a8 2e 30 be f0 00      01:52:49.800  READ DMA EXT
  25 00 b0 26 30 be f0 00      01:52:44.600  READ DMA EXT
  25 00 b8 1e 30 be f0 00      01:52:39.500  READ DMA EXT

SMART Self-test log structure revision number 1
Num  Test_Description    Status                  Remaining  LifeTime(hours)  LBA_of_first_error
# 1  Short offline       Completed without error       00%       808         -
# 2  Short offline       Completed without error       00%       665         -
# 3  Short offline       Completed without error       00%       656         -
# 4  Short offline       Completed without error       00%       316         -

Device does not support Selective Self Tests/Logging

seiken ★★★★★
() автор топика
Вы не можете добавлять комментарии в эту тему. Тема перемещена в архив.
← Свеженькая кубунта
Linux-hardware
Выбор ноутбука: 25000-28000р. →