Помогите разобраться, или подскажите хороший ман, а то не пойму как заставить работать иксы.
Linux TosDD 2.6.26-2-686 #1 SMP Wed Aug 19 06:06:52 UTC 2009 i686 GNU/Linux01:00.0 VGA compatible controller: Trident Microsystems Cyber 9525 (rev 49)Вот 2 конфига: первый, тот что сейчас в Debian, с ним X не стартует, идут полосы и все тупит. Второй - конфиг из Puppy, где иксы нормально стартуют и работают. Если конфиг из puppy подсунуть Debian-y - стартуют иксы, но глючат и показывают картинку из последней сессии Puppy (!?!), ощущение что видеопамять не очищается.
# xorg.conf (X.Org X Window System server configuration file)
#
# This file was generated by dexconf, the Debian X Configuration tool, using
# values from the debconf database.
#
# Edit this file with caution, and see the xorg.conf manual page.
# (Type "man xorg.conf" at the shell prompt.)
#
# This file is automatically updated on xserver-xorg package upgrades *only*
# if it has not been modified since the last upgrade of the xserver-xorg
# package.
#
# If you have edited this file but would like it to be automatically updated
# again, run the following command:
# sudo dpkg-reconfigure -phigh xserver-xorg
Section "InputDevice"
Identifier "Generic Keyboard"
Driver "kbd"
Option "XkbRules" "xorg"
Option "XkbModel" "pc105"
Option "XkbLayout" "us,ru"
Option "XkbOptions" "grp:alt_shift_toggle"
EndSection
Section "InputDevice"
Identifier "Configured Mouse"
Driver "mouse"
EndSection
Section "Device"
Identifier "Configured Video Device"
EndSection
Section "Monitor"
Identifier "Configured Monitor"
EndSection
Section "Screen"
Identifier "Default Screen"
Monitor "Configured Monitor"
EndSectionКонфиг из Puppy:
#Special base config file used in Puppy Linux.
# **********************************************************************
# Module section -- this section is used to specify
# which dynamically loadable modules to load.
# **********************************************************************
#
Section "Module"
# This loads the DBE extension module.
Load "dbe" # Double buffer extension
# This loads the miscellaneous extensions module, and disables
# initialisation of the XFree86-DGA extension within that module.
SubSection "extmod"
Option "omit xfree86-dga" # don't initialise the DGA extension
EndSubSection
# This loads the font modules
Load "type1"
Load "freetype"
# This loads xtrap extension, used by xrandr
Load "xtrap"
# This loads the GLX module (if present)
Load "glx"
# This loads dri module (if present)
Load "dri"
EndSection
# **********************************************************************
# Files section. This allows default font and rgb paths to be set
# **********************************************************************
Section "Files"
# The location of the RGB database. Note, this is the name of the
# file minus the extension (like ".txt" or ".db"). There is normally
# no need to change the default.
#RgbPath "/usr/X11R7/lib/X11/rgb"
# Multiple FontPath entries are allowed (which are concatenated together),
# as well as specifying multiple comma-separated entries in one FontPath
# command (or a combination of both methods)
#FontPath "/usr/X11R7/lib/X11/fonts/misc/"
#FontPath "/usr/X11R7/lib/X11/fonts/Type1/"
#FontPath "/usr/X11R7/lib/X11/fonts/TTF/"
EndSection
# **********************************************************************
# Server flags section.
# **********************************************************************
Section "ServerFlags"
# Uncomment this to disable the <Crtl><Alt><Fn> VT switch sequence
# (where n is 1 through 12). This allows clients to receive these key
# events.
# Option "DontVTSwitch"
# Enables mode switching with xrandr
# There is a report that this can cause Xorg not to work on some
# video hardware, so default is commented-out...
# but i want to use it in xorgwizard so leave on...
Option "RandR" "on"
EndSection
#everything past here is auto-generated by Puppy's Xorg Wizard...
Section "ServerLayout"
Identifier "X.org Configured"
Screen 0 "Screen0" 0 0
InputDevice "Mouse0" "CorePointer"
InputDevice "Keyboard0" "CoreKeyboard"
EndSection
Section "InputDevice"
Identifier "Keyboard0"
Driver "kbd"
Option "XkbRules" "xorg"
Option "XkbModel" "pc102"
Option "XkbLayout" "us" #xkeymap0
EndSection
Section "InputDevice"
Identifier "Mouse0"
Driver "mouse"
Option "Protocol" "auto" #mouse0protocol
Option "Device" "/dev/mouse"
#Option "Emulate3Buttons"
#Option "Emulate3Timeout" "50"
Option "ZAxisMapping" "4 5" #scrollwheel
EndSection
Section "Monitor"
#DisplaySize 230 170 # mm
Identifier "Monitor0"
VendorName "TOS"
ModelName "5081"
HorizSync 31.5-35
VertRefresh 50-61
#UseModes "Modes0" #monitor0usemodes
Option "PreferredMode" "800x600"
EndSection
Section "Modes"
Identifier "Modes0"
#modes0modeline0
EndSection
Section "Device"
# Available Driver options are:-
# Values: <i>: integer, <f>: float, <bool>: "True"/"False",
# <string>: "String", <freq>: "<f> Hz/kHz/MHz"
# [arg]: arg optional
#Option "AccelMethod" # [<str>]
#Option "SWcursor" # [<bool>]
#Option "PciRetry" # [<bool>]
#Option "NoAccel" # [<bool>]
#Option "SetMClk" # <freq>
#Option "MUXThreshold" # <i>
#Option "ShadowFB" # [<bool>]
#Option "Rotate" # [<str>]
#Option "VideoKey" # <i>
#Option "NoMMIO" # [<bool>]
#Option "NoPciBurst" # [<bool>]
#Option "MMIOonly" # [<bool>]
#Option "CyberShadow" # [<bool>]
#Option "CyberStretch" # [<bool>]
#Option "XvHsync" # <i>
#Option "XvVsync" # <i>
#Option "XvBskew" # <i>
#Option "XvRskew" # <i>
#Option "FpDelay" # <i>
#Option "Display1400" # [<bool>]
#Option "Display" # [<str>]
#Option "GammaBrightness" # [<str>]
#Option "TVChipset" # [<str>]
#Option "TVSignal" # <i>
Identifier "Card0"
Driver "vesa" #card0driver
VendorName "Trident Microsystems"
BoardName "Cyber 9525"
BusID "PCI:1:0:0"
EndSection
Section "Screen"
Identifier "Screen0"
Device "Card0"
Monitor "Monitor0"
DefaultDepth 24
Subsection "Display"
Depth 24
Modes "800x600"
EndSubsection
EndSection
